2.8 tft lcd shield library quotation

I gave up on the TFT Menu library when I was working on my project, there isn"t very good documentation except for the example and I only needed a single screen. Maybe I can answer a few questions from the code you posted:

I did a little experimenting with my TFT tonight. My current project has two joysticks attached to my Mega, so I just used these for test sensor values. If you just want to print out sensor values, here is an example sketch that displays time and pot values:

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel with controller XPT2046 attached by default and a optional capacitive touch panel with controller FT6206 attached by default, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This IPS TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel with controller XPT2046 attached by default and a optional capacitive touch panel with controller FT6206 attached by default, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino UNO. Solder three jumpers and you can use it at full speed on a Leonardo or Mega as well.

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. This shield needs fewer pins than our v1 shield, so you can connect more sensors, buttons and LEDs: 5 SPI pins for the display, another pin for the SPI touchscreen controller and another pin for uSD card if you want to read images off of it.

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

Add some sizzle to your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection and a capacitive touchscreen. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display has a capacitive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

This shield is the capacitive version as opposed to the resistive touchscreen we also sell. This touchscreen doesn"t require pressing down on the screen with a stylus, and has a nice glossy glass cover. It is a single-touch display.

This shield uses SPI for the display and SD card and is easier to use with UNO, Mega & Leonardo Arduino"s. The capacitive touchscreen controller uses I2C but you can share the I2C bus with other I2C devices.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Duemilanove/Diecimila). Solder three jumpers and you can use it at full speed on a Leonardo or Mega as well.

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. This shield needs fewer pins than our v1 shield, so you can connect more sensors, buttons and LEDs: 5 SPI pins for the display, 2 shared I2C pins for the touchscreen controller and another pin for uSD card if you want to read images off of it.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x & y location and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

This 2.8" LCD Shield from Waveshare is for the Arduino and also support resistive touch. The TFT screen support 32x2400 resolution. The screen has a standard Arduino interface and is compatible Arduino UNO and Leonardo.

The 2.8" screen has an onboard stand-alone touch controller, better touching than solutions that use AD pins directly for touch control. The PWM backlight control allows you to adjust the backlight to a comfortable level, and the micro SD slot provides an easy way to store photos for displaying. Controlled via SPI, and only a few Arduino pins are used.

Displaying a custom image or graphic on a LCD display is a very useful task as displays are now a premium way of providing feedback to users on any project. With this functionality, we can build projects that display our own logo, or display images that help users better understand a particular task the project is performing, providing an all-round improved User Experience (UX) for your Arduino or ESP8266 based project. Today’s tutorial will focus on how you can display graphics on most Arduino compatible displays.

The procedure described in this tutorial works with all color displays supported by Adafruit’s GFX library and also works for displays supported by the TFTLCD library from Adafruit with little modification. Some of the displays on which this procedure works include:

For this tutorial, we will use the 2.8″ ILI9325 TFT Display which offers a resolution of 320 x 340 pixels and we will display a bitmap image of a car.

To demonstrate how things work, we will use the 2.8″ TFT Display. The 2.8″ TFT display comes as a shield which plugs directly into the Arduino UNO as shown in the image below.

Not all Arduino displays are available as shields, so when working with any of them, connect the display as you would when displaying text (we recommend following the detailed tutorial for the display type you use of the above list). This means no special connection is required to display graphics.

Image2Code is an easy-to-use, small Java utility to convert images into a byte array that can be used as a bitmap on displays that are compatible with the Adafruit-GFX or Adafruit TFTLCD (with little modification) library.

To reduce the amount of code, and stress involved in displaying the graphics, we will use two wonderful libraries; The GFX library and the TFTLCD library from Adafruit.

The GFX library, among several other useful functions, has a function called drawBitmap(), which enables the display of a monochrome bitmap image on the display. This function allows the upload of monochrome only (single color) graphics, but this can be overcome by changing the color of the bitmap using some code.

The Adafruit libraries do not support all of the displays but there are several modifications of the libraries on the internet for more displays. If you are unable to find a modified version of the library suitable for your the display, all you need do is copy the code of the drawBitmap() function from the GFX library and paste it in the Arduino sketch for your project such that it becomes a user-defined function.

As usual, we start writing the sketch by including the libraries required. For this procedure, we will use the TFTLCD library alone, since we are assuming you are using a display that is not supported by the GFX library.

The last section of the code is the drawBitmap function itself, as earlier mentioned, to use the drawbitmap() function with the Adafruit TFTLCD library, we need to copy the function’s code and paste into the Arduino sketch.

The shield is fully assembled, tested, and ready to go. No wiring, no soldering! Simply plug it in and load up the library - you"ll have it running in under 10 minutes!

After that I have been able to connect the touch-sensitive part of the screen as well, and it reads x+, x-, Y+ and y- fairly well using Touch-Screen-Library (https://github.com/adafruit/Touch-Screen-Library) (I still have to some more calibration though).

I have been running into problems when I wanted to actually display something on the screen using TFT LCD library (https://github.com/adafruit/TFTLCD-Library) (and the GFX library (https://github.com/adafruit/Adafruit-GFX-Library))...

Connect the seventh pin RST (Reset) to the Arduino Reset line. This will reset the panel when the Arduino is Reset. You can also use a digital pin for the LCD reset but this will save us a pin.

It should be 0x9328 or 0x9325 so if you see something like 0x8328 that means that the D8 pin is not wired correctly and if you get 0x9228 then pin D0 is not wired correctly.

Adafruit is also selling a shield version of you display and I think you can use this to verify you pin assignment. With this: https://github.com/adafruit/TFTshield/blob/master/schem.png

and this: http://arduino.cc/en/uploads/Main/ArduinoUno_R3_Front.jpg you can figure out how the pin assignment is supposed to work with a shield/UNO. now you need to either replicate or map this to you Teensy.

I just got my teensy3 displaying the graphicstest on my LCD. Your description here of how to do it was just fine, though it took me a couple of tries to get the wiring right (my fault, though)

I got this going as well thanks to your guidance. While I was fiddling with the pinouts etc. in pinmagic, I did a couple of other things, in Adafruit_TFTLCD:

inline Adafruit_GFX& operator() (uint8_t x, uint8_t y,uint16_t c) {setCursor(x,y); setTextColor(c); return *this;} //use along w Streaming.h to support: tft(col,line,color)<<"a="<

inline Adafruit_GFX& operator() (uint8_t x, uint8_t y,uint16_t c,uint8_t s) {setCursor(x,y); setTextColor(c); setTextSize(s); return *this;} //use along w Streaming.h to support: tft(col,line,color,size)<<"a="<

http://www.ebay.de/itm/New-2-4-inch-TFT-LCD-Module-display-240-x-320-Screen-ILI9325-with-touch-pen-/281090515728?pt=UK_BOI_Electrical_Components_Suppl ies_ET&hash=item41724ce310

They are not using the current library, as you guessed. I tried patching pin_magic.h with the teensy 3 mods, but more is required for the current TFTLCD library. The library now supports DUE, and the constructor does a lot of work mapping the control pins into port register access for set/clear operations. Maybe the teensy equivalent would be to use

For the hacked together version I"ve been using and testing on a 3.1, the __AVR__ style of pin/port mapping from the new library seems to be what I"ve been using. csPort = portOutputRegister(digitalPinToPort(cs)); etc

And I measured 32.7ma at 3.3v for the TFTLCD, so I powered it from the teensy 3 3.3v pin. This is on older Adafruit TFTLCD, http://www.adafruit.com/products/335

OK, maybe I"m confused, but does that library drive the Adafruit display in 8-bit mode (as described at https://learn.adafruit.com/adafruit-2-dot-8-color-tft-touchscreen-breakout-v2/8-bit-wiring)? The TFTLCD library has the disadvantage of needing more pins, but my impression was that it could achieve a higher throughput of data to the display, or am I mistaken in that as well?

Well, this is awkward. I had a 2.8" ILI9325 screen from Adafruit working on a Teensy 3.0 a couple of years back. I just tried to rebuild the code for that and I seem to have lost some files. Specifically I"m looking for the right Adafruit_TFTLCD library (well, I think that"s all I"m looking for). The current library from Github doesn"t compile with a Teensy3, and I recall I had to edit the pin_magic file as per ZTiK.nl (earlier in this thread). But the later files from Github look different now. I don"t seem to be able to go back to an earlier branch on Github.

I can see Paul has posted an ILI9341_t3 library, but mine is an ILI9325. Has anyone got a working copy of the library that works with my combination posted somewhere? I"d rather not upgrade the hardware at this stage, the problem I have is software.