lcd screen on pc case free sample

Case modding took off in the late 90s, and taught us all that computers could (and should!) look awesome. Much of the aesthetic went mainstream, and now tons of computer cases come with lights and windows and all the rest. [WysWyg_Protogen] realized those simple case windows could be way cooler with a neat LCD hack, and set to work.

The concept is simple. Take an old LCD monitor, remove the backlight and extraneous hardware, and then install it to the window in a computer case. When lit from behind via LEDs in the case, the screen creates a ghostly display through which the computer’s internals can still partially be seen. It’s a really compelling effect, and in theory, quite easy to achieve. All one need do is mount the stripped-down screen to the case and pipe it video from the graphics card.

In practice, it’s a little tricky. Disassembling the screen and removing things like the anti-glare coating can be tough to do without damaging the delicate panel inside. The windows typically used on computer cases can dull the effect, too. However, [WysWyg_Protogen] is continuing to tinker with the project and the results are getting increasingly impressive with each iteration. It doesn’t photograph too well, but it looks truly amazing in motion.

We often forget LCDs are transparent in their basic form, as we generally only use them with backlights or reflective backers. They really do look great when used in this transmissive way, though. Video after the break.

Actually beside myself right now. How does this look this good? This was a trash pile monitor and this looks like a 700 dollar case upgrade pic.twitter.com/4yBXlcY921

I saw a really cool video of a PC case called "Snowblind", that had a transparent LCD Screen as a side panel. I was amazed over how cool it was. The only problem was that it was really expensive. Therefore, I tried making my own! In this instructables I will go through how I made it, and how you could make your own. The best of all, since it was made from an old monitor that was thrown away, it was basically free! I just added some LED strips on the inside of the case to get better contrast on the screen. You could probably re-use the monitors backlight, but it"s safer and easier to just get some cheap LED strips.

The first step is to disassemble the monitor. The disassembly is pretty well documented in the video I made. I have also added some pictures so you can see the steps. The steps of disassembling the monitor will not be the same for every monitor, therefore I will not go into detail of every step.

PS: DO NOT DISASSEMBLE THE MONITOR UNLESS YOU KNOW WHAT YOU ARE DOING. THE PSU COULD STILL HAVE SOME CHARGE IN THE CAPACITORS THAT MIGHT ELECTROCUTE YOU.

You will have to reverse engineer the controller to find the power connections, and solder a new power connector on. This way, you can use the ATX power supply that powers your computer. I used a multimeter, where I had one probe to the ground plane (For example around the mounting screws), and used the other probe to search for 5V or 12V power on the pins coming from the power supply.

First, remove the frame of the panel. It is fixed with clips, so just bend the frame a little and lift the frame up. Next, separate the front LCD from the backlight. For the next step, you will have to be careful. This step involves removing the anti glare film. It is glued to the panel, and therefore it"s easy to break the LCD when trying to remove it.

To remove it place some paper towels on top, and then carefully pour water on it until the towels are soaked. Let it sit for around 24 hours. After 24 hours, try to start pealing the layer from the corner. If it sticks in some places, place a wet paper towel on that space and wait some more.

Then you are done modding the LCD! Now, you can hook it up to the panel and test it. Just be careful with the ribbon cables going from the LCD PCB to the panel.

The side panel of this case fits the LCD perfectly. Just line it up to the side facing the back, and to the top, and use some tape to tape it to the glass. Then, use some vinyl on the outside where the LCD is not covering the glass.

Next, use some double-sided tape to fix the LED strips to the inside of the frame. Then, solder them together in series. You can now solder on a wire and connect them to the 12V line of the Molex connector.

It"s really important to have lots of lights inside the case, to make it easier to see the LCD. Therefore, try to fill the case with even more LED strips.

You are now ready to assemble everything. In this case, the controller fit nicely in the hard drive compartment, so I glued it there and fed the ribbon cable through the hole in the inside of the case. That way it was pretty much hidden inside the case.

Now you can carefully mount the side panel back on the computer. You might have to drill a new hole for the thumb screw in the back to make it fit properly.

You can now power up the computer, open the screen settings and set it up for dual screens. You might have to flip the display 180 degrees too. When you have done that, open Wallpaper Engine and set a wallpaper of choice!

I have the same problem, I have read on google that the lcd could also be 3,3v (check if you have 3.3v lanes) so i will be trying to solder a sata cable to it because it comes with 3,3 and 5v connectors but the im not sure if save to use sata cables0

Hey I have a little question, I also have a Dell 1905FP, but I think it"s an older model because I don"t have a ribbon cable but a normal cable with a plug. My problem is that I have peeled off one film but it still looks like there is a second film on the back because it is still a little blurry. But I"m afraid that if I try to pull them off, my LCD display will break. Maybe you have an idea. Thanks in advance

Stunning result ! Bought for 10€ a Dell 1907FPc which is fairly similar to yours. I have trouble identifying the pin layout to find the 5V pin. Did you plug in the power supply to your AC while checking with your multimetter ?0

Great tutorial and video! I"m trying my hand at replicating your process and I even got my hands on the exact monitor. I have reached the point where I"ve disassembled the panel and controllers, and discharged the capacitors from the PSU, but I am a little stuck at this point because I don"t know how to wire up the molex header. I watched your video and saw that you had two wires soldered to the power connector. Which connectors are they and where do they go on the molex cable? Thank you!

You probably have figured this out by now, but he used the black and red from molex to power the monitor and used the yellow and black to power his led

Really neat. I saw the same snowblind case and wanted it but too expensive. I also saw someone who made their own using a USB monitor. But I like your setup better.2

Terrific job! May I ask why you would need to remove the front polarizer? If my understanding is correct, both the front and back polarizers are needed in order for the LCD to work properly (i.e., the light gets polarized by the back polarizer first, and then passes through the front polarizer)? You comments will be appreciated!

Hey, great work on this project. I wanted to buy the snowbind case but couldn"t justify the cost. I have the same case and I ended up picking up the same monitor that you used in your project.

Is it possible that you post or send me photos of the inside of the case when you have this installed? I"m just a bit confused on how you wired up everything?

I tried taking some photos, but I have covered the screen PCB with a cover, so it was hard to see in the photos. I basically just laid it inside the case with a 90-degree angle. I tried drawing it here: (view from the front)0

I used "wallpaper engine" to just set the animations as wallpaper on that screen. I mentioned it in the last step, but I could probably make a own step about that, if you are interested in more details.2

I think you should have more pics and info about the re- mounting the LCD. After all if you don"t do it right all that work is for nothing. While I understand your wiring diagram, I think that it should be explained and a larger part of this Instructible...for example to get white lite your are powering all 3 lanes (red,green,blue) on the RGB tape.

Hello, Wonderfull project, I have the same case and I would love to do it (if I have time and the screen to the right size). Just a question, can you put a photo of the cable connection to see if it"s easy to open the case ? One little suggestion, instead of connecting the panel to the graphic card (which mean to run a cable outside, why don"t you use a USB to VGA or DVI converter (like this https://www.amazon.fr/Adaptateur-convertisseur-adaptateur-Affichage-multi-écrans/dp/B079L81FRD/ref=asc_df_B079L81FRD/?tag=googshopfr-21&linkCode=df0&hvadid=227894524041&hvpos=&hvnetw=g&hvrand=17927658121409960098&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9055710&hvtargid=pla-442905712462&psc=1) ?More CommentsPost Comment

The Hyte Y60 is one of the best PC cases on the market, and it’s getting a big upgrade in the form of an official DIY mod kit. TheHyte Y60 LCD DIT kit is available now for $120, allowing you to replace one of the tempered glass panels of the case with a programable screen.

If you frequent PC builds on Reddit or Instagram, you’ve probably seen this mod before. For months, community members have bought screens that fit in the gap in Hyte’s case and used community 3D-printed mounts to attach them. In a Reddit thread several months back, in fact, the company responded to a user’s build with “THIS IS SO COOL.”

Hyte is now selling the kit in an official capacity. The $120 kit includes the screen, a driver board to deliver power and data to the screen, and the cables to hook everything up. Unfortunately, it’s not an all-in-one solution out of the box. You still need to 3D-print a mount for the screen, but Hyte includes the file you need to print.

The screen comes with a resolution of 1920 x 515, and it’s not something you can control through software. Instead, the included driver board includes a mini HDMI connection that you’ll need to route through your PC and connect to your graphics card. After that, the panel will show up as another monitor in your operating system.

Originally, the mod was made for Aida64’s SensorPanel software, which allows you to display sensors like system utilization, CPU speed, and temperature in custom themes. You can still download and use these themes with Hyte’s DIY kit, but you can also display images, videos, or anything else you want.

The LCD kit was among Hyte’s CES 2023 announcements. The company also announced the new Hyte Y40 case, which is a slimmed-down version of the wildly popular Y60. Instead of the dual-chamber design of the Y60 and fish tank-like look, the Y40 opts for a traditional power supply basement and a slimmer form factor.

Although it’s smaller overall, the Y40 actually has more space for your graphics card, which could make a big difference with GPUs like the RTX 4090. The vertical GPU mount includes four slots as opposed to the three slots on the Y60. The case is also $50 cheaper, clocking in at $150.

If you want a secondary screen but can’t quite fit one onto your desk, you might want to check out ASRock’s latest invention — a PC side panel display.

PC owners have all that space on their chassis, and nothing to do with it. As long as you’re willing to give up being able to easily peer inside the case (and admire the RGB light show, if that’s your thing), you might like ASRock’s 13.3-inch Side Panel Kit. This is essentially a monitor, similar to that in a laptop, that is attached to the inside of your case.

As the panel is installed within the chassis, your case needs to have a side panel made of transparent tempered glass. It has to be sturdy enough to hold the screen, but it also needs to be see-through so that you can see it in the first place.

For a little side monitor, the IPS display sounds decent. It measures 13.3 inches, has a 16:9 aspect ratio, 1080p resolution, and a basic 60Hz refresh rate. The display seems to be fairly bright and suitable for all kinds of things.

You could use it to simply monitor your PC’s temperatures and speeds, or you could turn it into a proper secondary screen for productivity or entertainment. Granted, needing to view it through the case will probably diminish the experience a bit, but it’s still a fun gadget if you’ve got limited desk space and want an extra screen. If you do get one and plan to use it for productivity, you might need to re-think the placement of your PC case to avoid constantly having to turn and look to the side.

With all that said, there’s one catch — not that many people might be able to use this gadget, and that’s all because of the fact that it has an embedded DisplayPort (eDP) connector. This means that it runs both power and video through just one cable, and while that’s handy, most motherboards don’t support this kind of connection.

As of right now, only ASRock boards support this side panel. Tom’s Hardware reports that only some of the best motherboards for Intel and AMD will qualify, including the Z790 PG Lightning, Z790 Pro RS, Z790 Pro RS/D4,  Z790 LiveMixer, Z790M-ITX WiFi, Z790 PG Lightning/D4, Z790 Steel Legend WiFi, B650E PG-ITX WiFi, and lastly, H610M-ITX/eDP.

This availability is likely to affect the popularity of ASRock’s new gadget. However, if you have one of the required motherboards or you’re planning an upgrade soon, it seems like a fun addition to a PC build.

Hi everybody! Bill Owen from Mnpctech. I hope you"re having a great day! Several people have asked if I could share the steps on how I do my Touchscreen LCD mod in PC Computer case bezels, and you’ve come to the right video!

I’ve been using this Amazon 5 Inch Capacitive Touch Screens for $52.99 delivered on Amazon Prime, I’ll posted a link in Video description. The kit comes a with Micro USB for power and HDMI video connector, but these cables are too short for these PC case mods. It includes M3 stand-offs, a Driver Disc and some Instructions. It’s a 5 point Capacitive Touch screen with a Resolution of 800 x 460, which is just fine for it’s 5” viewing screen In addition to the LCD touchscreen, I will buy the following cables for my Desktop Custom PC LCD Case Mod.

One 3ft “Right Angle” 270 degree HDMI cord, 6” 90 Degree Angle HDMI Extension Adapter, and 3ft USB Male to Micro B power connector. For Mounting the LCD Touchscreen Panel, I use 3/16” thick Black acrylic to make custom mounting brackets for the LCD touch screen.

You can PAUSE the video on this page to record the measurements that I’ve made for cutting the acrylic. This PC Case Mod is very easy. "The reason I’m making brackets for my desktop PC LCD Monitor Mod?" I want the ability to easily install or remove the Touchscreen with thumbscrews. I’m using 1/8” drill bit for acrylic, and 6/32 thread tap, These Black thumbscrews from Mnpctech.com. I’ll use the 1/8” drill bit to increase the diameter of the holes in the LCD pcb frame.

I discovered these drill bits for plastic several years ago, Notice the bit isn’t splintering or cracking the acrylic as I make the holes. Mnpctech stocks a variety of these drills bits. My mod requires Twelve 6/32 washers, and links posted in description, “Why so many washers?” We want the Touchscreen to mount flush on the backside of the bezel, I also don’t want to apply any unnecessary pressure to the screen or the PCB, See how this sheet of paper easily slides under the screen Next stage is cutting the hole in the bezel, The best PC case for this mod is the ones without optical drive bays, which every popular case manufacturer now offers.

If you’re using an older case with 5.25 drive bays, you could attach a mounting plate with 5” opening that covers THREE 5.25 bays. That’s how we did this mod in the early days of PC Modding. Determine and measure out a location in the center of your bezel, you can also mount the LCD vertically if you prefer, and just change the screen orientation in Windows. Since the bezel is plastic, I’m using a Dremel with 1.5” reinforced cut off wheel, Don’t forget to always wear eye protection when using power tools. Oops, WTH? Hahaha After cutting our 5” diagonal square hole, I’ll hand file the edges so everything is precise and clean. You may have to remove sound insulation foam from backside of your bezel, I’m using E6000 adhesive to attach the two mounting brackets. This adhesive is very GOOEY at first, so consider masking off the screen, to prevent getting any of this on it. I like that it’s tacky for couple of minutes, so I have time to position the LCD in place, and then I’ll temporarily tape it in place while it cures overnight.

Mounting your Touchscreen LCD in the PC this way allows you to easily remove and re-install the LCD at any time. Especially if you ever need to replace it for some reason. Let’s get this LCD touchscreen connected to the PC, all of the cables are routed from the front to thee rear PCI slots. *3ft “Right Angle” 270 degree HDMI cord *6” 90 Degree Angle HDMI Extension Adapter cable, I plug this compact cable into the Touchscreen to save space. *3ft USB Male to Micro B power connector This mod is great if you want an extra screen for monitoring your hardware and temps. You can also display Weather or calendar or email notifications,

Check out http://www.Rainmeter.net this community offers several hundred custom mad graphic interfaces for FREE, and you can configure your screen to display a variety of updated information tasks Thanks for watching! And Again, all of the products used in this PC case mod are listed in the video description.

There are PC builders out there that can put a system together, check its function to make sure everything is running smoothly, and then use it without ever looking at its vital signs again.

If you’re a stat-checker like me, you’ve likely seen external system monitors in custom systems. If your available time for tinkering is like mine, you likely still look at those with envy, as getting them installed and set up all on your own takes time and a skillset that many don’t have.

Recently though, Lamptron has shifted their attention to PC monitoring hardware. They currently offer more than ten different hardware monitors in different sizes and styles, with more on the way!

All of Lamptron’s monitors are designed to display data reported by the diagnostic and monitoring software AIDA64, one of the oldest and most feature-packed system monitoring software packages available today.

First launched as ASMDEMO in 1995 and reintroduced as AIDA32 in 2001, AIDA64 is the culmination of decades of work and improvement and is among the best-known monitoring software packages on the market. The amount of information about your system that’s easily obtainable through AIDA64 is honestly incredible, and Lamptron’s system monitors make it easy to access.

First and foremost, Lamptron’s hardware monitors currently all offer the same user interface and functionality. Powered by a micro USB connection and interfacing with your PC by way of a full-sized HDMI connection, they’re universal and easy to use.

Since they connect through HDMI, Lamptron’s system monitors function as an additional display. While that means that your video source will have to be multi-monitor capable in order to use them, it also makes them simple and eliminates any need for additional drivers.

You will of course need a copy of the AIDA64 software. If you don’t have a copy don’t worry – the flash drive included with your Lamptron monitor includes a fully-licensed copy of the software. Licensing for AIDA64 (as of the date of this post) starts at $49.99US, so this is a nice inclusion.

AIDA64 is capable of monitoring nearly every piece of data about your PC and displaying it on the Lamptron System Monitors. Anything from memory utilization to disk activity to per-core CPU temperatures. Temps, voltages, clock speeds, power values, disk space – pretty much anything you might want to know about what your PC is doing can be monitored in real time and displayed.

What’s more, AIDA64 allows you to build a completely custom screen for your new monitor. You can decide not only which pieces of data are displayed, but customize the way they’re displayed. Bars, graphs, gauges, simple numbers – the choice is yours. You can customize nearly every aspect of your screen, right down to the color and font used in the different data displays and more. You can add your own images and even make your own custom gauges if you’re savvy with image editing software.

The HM022 is the smallest of the monitors that Lamptron offers, with a diminutive 2.2-inch LCD. Why would you want a monitor with a screen that small, you ask? Because this one is built into a graphics card support bracket.

The HM022 is unique among Lamptron’s monitors in that it only requires only a USB connection to function – both power and data are supplied. The ARGB function has its own connection, with a passthrough plug to facilitate daisy chaining.

The HC060 monitor offers a six-inch LCD screen and comes with mounts to install in any dual 5.25” position in a PC case. Fully enclosed and only 6mm thick, the HC060 can also be housed outside your PC case, though no mounts or stands are included for this purpose.

Moving up in screen size brings us to the HC070. Offering a 7-inch screen and matching the 6mm thickness of the HC060, the HC070 is designed to mount in a PCI slot inside your case.

The HM070 monitor is a modification of the HC070. While using the same 7-inch screen, it provides an enclosure 10mm thick that allows it to function freestanding outside of the PC case. It also includes the same mounting options as the HC070.

A further modification of the HC070, the HM070 LIFT places the 7-inch LCD screen in a larger housing that’s 30mm thick and includes an option for wall mounting.

Though the screen on the HM088 is an 8.8” LCD, its form factor is longer and narrower than the 070 series. Designed to be mounted inside your PC case in a PCI location, its length will cover a large portion of most side panel windows.

The HM101 moves away from the smaller screens used in previous models, offering a 10.1-inch LCD and includes a single-position stand for placing it on a desk.

An evolution of the HM101, the HM101 Touch has the same screen size, but the bezel is larger and notably thicker along one of the long edges. Touch-control enabled, the HM101 Touch has a virtual keyboard function that allows the user to interact with the monitor directly.

Similar to the HM088, the HM140 offers a long narrow form factor, but with a full 14-inch LCD screen. Mounting for inside the PC case is included. While it is 14mm thick, the shape of the HM140 will not allow freestanding use without a stand of some sort.

The HM140 Touch brings a screen identical in size to the HM140, but wrapped in a thicker bezel and including the same multi-position stand that comes with the HM101 Touch. Virtual keyboard support is also present.

The largest of Lamptron’s monitors, the HM173 is a gargantuan 17.3 inches of screen. Sharing the same uniform narrow bezel as the HM101, it also comes a non-adjustable single-position stand.

Lamptron has really stepped up to the challenge with their new line of system monitors. By using AIDA64 as their data connection they’ve made installation simple and given users a huge array of data to choose from when deciding what to display. The sheer variety of size and shape options are amazing, and anyone wanting to get started with a separate system monitor will be able to find something to fit their needs.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

The specification is subject to change without notice in advance. The brand and product names are trademarks of their respective companies. Any configuration other than original product specification is not guaranteed.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Once you have found the correct part number, see HP Consumer Notebook PCs - Ordering HP certified replacement parts. Use the instructions in this document to order a replacement part.

HP recommends that you only order parts from an authorized HP repair parts dealer. Parts ordered from third-party companies might not perform as expected and might cause additional

The basic parts of a desktop computer are the computer case, monitor, keyboard, mouse, and power cord. Each part plays an important role whenever you use a computer.

The computer case is the metal and plastic box that contains the main components of the computer, including the motherboard, central processing unit (CPU), and power supply. The front of the case usually has an On/Off button andone or more optical drives.

Computer cases come in different shapes and sizes. A desktop case lies flat on a desk, and the monitor usually sits on top of it. A tower case is tall and sits next to the monitor or on the floor. All-in-one computers come with the internal components built into the monitor, which eliminates the need for a separate case.

The monitor works with a video card, located inside the computer case, to display images and text on the screen. Most monitors have control buttons that allow you to change your monitor"s display settings, and some monitors also have built-in speakers.

Newer monitors usually have LCD (liquid crystal display) or LED (light-emitting diode) displays. These can be made very thin, and they are often called flat-panel displays. Older monitors use CRT (cathode ray tube) displays. CRT monitors are much larger and heavier, and they take up more desk space.

The keyboard is one of the main ways to communicate with a computer. There are many different types of keyboards, but most are very similar and allow you to accomplish the same basic tasks.

The Print Screen, Scroll Lock, and Pause/Break keys are at the top-right corner of the keyboard. The Print Screen key takes a picture of your screen (called a screenshot) that you can edit or save using a graphics program. Scroll Lock and Pause/Break are rarely used today, so some keyboards don"t have them.

The Escape (Esc) key allows you to stop a function or action. For example, if a webpage is taking a long time to load, you can press the Escape key to stop loading it.

The function keys are labeled F1 through F12. Some programs use these keys as shortcuts for common tasks. For example, in many programs, F1 opens the Help file.

The Tab key is used to create indents in word processing programs. Also, if you are filling out a form online, you can use the Tab key to switch to the next field.

The Control (Ctrl), Alternate (Alt), and Shift keys are designed to work in combination with other keys. Typically, you hold down Ctrl, Alt, or Shift and then type another key to perform a specific task. For example, in many programs, typing Ctrl+S will save a file.

The numeric keypadresembles a calculator keypad. Many users find that it is easier to type numbers using this keypad. On some keyboards, these keys double as arrow keys.

The Enter key (also known as the return key) executes commands. For example, while on the Internet, you can type a website address and then press Enter to go to the site. It is also used to start a new line in word processing programs.

The mouse is another important tool for communicating with computers. Commonly known as a pointing device, it lets you point to objects on the screen, click on them, and move them.

There are two main mouse types: optical and mechanical. The optical mouse uses an electronic eye to detect movement and is easier to clean. The mechanical mouse uses a rolling ball to detect movement and requires regular cleaning to work properly.

There are other devices that can do the same thing as a mouse. Many people find them easier to use, and they also require less desk space than a traditional mouse. The most common mouse alternatives are below.

Touchpad: A touchpad—also called a trackpad—is a touch-sensitive pad that lets you control the pointer by making a drawing motion with your finger. Touchpads are common on laptop computers.

Dust, food, liquid, and other particles can get stuck underneath the keys on your keyboard, which can prevent it from working properly. The basic cleaning tips below can help keep your keyboard clean.

Moisten a cotton cloth or paper towel with rubbing alcohol and use it to clean the tops of the keys. Do not pour alcohol or any other liquid directly onto the keys.

Reconnect the keyboard to the computer once it is dry. If you are connecting it to a PS/2 port, you will need to connect it before turning on the computer.

If you spill liquid on the keyboard, quickly shut down the computer and disconnect the keyboard. Then turn the keyboard upside downandallow the liquid to drain.

If the liquid is sticky, you will need to hold the keyboard on its side under running water to rinse away the sticky liquid. Then turn the keyboard upside down to drain for two days before reconnecting it. Please note that the keyboard may not be fixable at this point, but the method above is probably the best option.

Optical mice require no internal cleaning because they do not contain any rotating parts; however, they can get sticky over time as dust collects near the light emitter. This can cause erratic cursor movement or prevent the mouse from working properly.

If you have a mechanical mouse, remove the tracking ball by turning the ball-cover ring counter-clockwise. Then clean the tracking ball and the inside of the mouse with a cotton cloth moistened with rubbing alcohol.

Allow all of the parts to dry before reassembling and reconnecting the mouse. If you are connecting it to a PS/2 port, you will need to connect it before turning on the computer.

If you just want to give the mouse a quick cleaning, place it on a clean sheet of paper and move the mouse back and forth. Some of the dust and particles should rub off onto the paper.

Dirt, fingerprints, and dust can make your computer screen difficult to read; however, it"s easy to clean your screenwhen needed. There are monitor-cleaning kits you can buy, but they may damage your monitor if they"re designed for a different type of monitor. For example, a monitor cleaner that is designed for glass screens may not work with some non-glass LCD screens. The safest method is simply to use a soft clean cloth moistened with water.

From time to time, you should clean your computer case and the sides and back of the monitor to avoid a buildup of dust and dirt. Here are a few tips you can use when cleaning these surfaces.

Ammoniadiluted with water—orglass cleaner comprised mostly of ammonia and water—is a safe cleaning solution for computer surfaces. The milder the solution, the better.

Clean the monitor housing and case (butnotthe monitor screen) by spraying a safe cleaning solution onto a paper towel or anti-static cloth and wiping in a downward motion.

Don"t restrict airflow around your computer. A computer can generate a lot of heat, so the casing has fans that keep it from overheating. Avoid stacking papers, books, and other items around your computer.

Many computer desks have an enclosed compartment for the computer case. If you have this type of desk, you may want to position the case so it is not against the back side of the desk. If the compartment has a door, you may want to leave it open to improve airflow.