mipi dsi lcd panel datasheet for sale

SL-TFT7-TP-720-1280-MIPI  7” display module is based on PH720128T003-ZBC02 Powertip high quality LCD-TFT. Module is equipped with MIPI-DSI (2 lanes) embedded display interface, built-in CTP (capacitive touch panel) and integrated touch panel controller (I2C).

The module SL-TFT7-TP-720-1280-MIPI contains all DC/DC  converters that are necessary for single rail power supply. Recommended power supply voltage is 3.3V or optionally +5V.

The PH720128T003-ZBC02 Powertip display matrix size is 1280×720 pixels (RGB, up to 24 bits), communication and data interface are TTL-LV (3.3V) compatible. LCD-TFT and CTP are covered with protective glass.

MIPI Mobile Industry Processor Interface is a relatively new standard, mainly used in mobile device applications. The application can be divided into DSI (display bus interface) serial display interface, CSI (camera serial interface), DPI (display pixel interface). DSI defines a high-speed serial interface between the main processor and the display module. The MIPI TFT LCD module introduced by Raystar has a high-speed advantage compared to the RGB interface. Our MIPI DSI standard TFT LCD display module contains different features, including high brightness, wide temperature, and wide viewing angle, etc. You are able to quickly select your suitable products by using the filters below.

First, you need to check whether this display has On-cell or In-cell touch panel, if has, it only needs to add a cover glass on it. If not, it needs an external touch panel.

Because the shape of the cover glass depends on the design of the clients, to avoid infringement of appearance, most of the developers need different customized touch panels.

WF50DTYA3MNN0 is a portrait mode 5 inch IPS TFT-LCD display module, resolution 720 x1280 pixels. This 5 inch TFT-LCD module supports MIPI DSI interface and is featured with an IPS panel which has the advantages of a wider viewing angle of Left:80 / Right:80 / Up:80 / Down:80 degree (typical) and having HD resolution, contrast ratio 800 (typical value). It can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃. This 5 inch MIPI LCD Display Panel has module dimension of 66.10 x 120.4 mm and AA size of 62.1 x 110.4 mm; it integrated driver IC ILI9881C on the module, power supply for analog range 2.5v to 3.6v.

This 5" DSI screen for Raspberry Pi comes from customer returning order.The quality and functionality is exactly same as original OSOYOO 5" DSI screen.You will save 30% from original price.The detail of the original product is as following:

The Display Serial Interface (DSI) is a specification by the Mobile Industry Processor Interface (MIPI) Alliance aimed at reducing the cost of display controllers in a mobile device. It is commonly targeted at LCD and similar display technologies. It defines a serial bus and a communication protocol between the host, the source of the image data, and the device which is the destination. The interface is closed source, which means that the specification of the interface is not open to the public. The maintenance of the interface is the responsibility of the MIPI Alliance. Only legal entities (e.g. companies) can be members. These members or the persons commissioned and approved by them have access to the specification in order to use it in their possible applications.

At the physical layer, DSI specifies a high-speed (e.g. 4.5Gbit/s/lane for D-PHY 2.0differential signaling point-to-point serial bus. This bus includes one high speed clock lane and one or more data lanes. Each lane is carried on two wires (due to differential signaling). All lanes travel from the DSI host to the DSI device, except for the first data lane (lane 0), which is capable of a bus turnaround (BTA) operation that allows it to reverse transmission direction. When more than one lane is used, they are used in parallel to transmit data, with each sequential bit in the stream traveling on the next lane. That is, if 4 lanes are being used, 4 bits are transmitted simultaneously, one on each lane. The link operates in either low power (LP) mode or high speed (HS) mode. In low power mode, the high speed clock is disabled and signal clocking information is embedded in the data. In this mode, the data rate is insufficient to drive a display, but is usable for sending configuration information and commands. High speed mode enables the high speed clock (at frequencies from tens of megahertz to over one gigahertz) that acts as the bit clock for the data lanes. Clock speeds vary by the requirements of the display. High speed mode is still designed to reduce power usage due to its low voltage signaling and parallel transfer ability.

The communication protocol describes two sets of instructions. The Display Command Set (DCS) is a set of common commands for controlling the display device, and their format is specified by the DSI standard. It defines registers that can be addressed and what their operation is. It includes basic commands such as sleep, enable, and invert display. The Manufacturer Command Set (MCS) is a device-specific command space whose definition is up to the device manufacturer. It often includes commands required to program non-volatile memory, set specific device registers (such as gamma correction), or perform other actions not described in the DSI standard. The packet format of both sets is specified by the DSI standard. There are Short and Long Packets, Short Packet is 4 bytes long; Long Packet can be of any length up to 216 bytes. Packets are composed of a DataID, Word count, Error Correction Code (ECC), Payload and Checksum (CRC). Commands that require reading data back from the device trigger a BTA event, which allows the device to reply with the requested data. A device cannot initiate a transfer; it can only reply to host requests.

MIPI A-PHY® is a long-reach serializer-deserializer (SerDes) physical layer interface for automotive applications, including ADAS, ADS and other surround-sensor applications, including cameras and in-vehicle infotainment (IVI) displays.

MIPI A-PHY was developed by theMIPI A-PHY Working Groupand is available to MIPI Alliance members. A-PHY v1.0 was also adopted as an IEEE standard in June 2021 and is available asIEEE 2977-2021. A-PHY v1.1 will also be submitted for adoption as an IEEE standard.

5 inch IPS TFT-LCD display module, resolution 720 x1280 pixels. This 5 inch TFT-LCD module supports MIPI DSI interface and is featured with IPS panel which having the advantages of wider viewing angle of Left:80 / Right:80 / Up:80 / Down:80 degree (typical) and having HD resolution, contrast ratio 800 (typical value). It can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃.

This 5 inch MIPI LCD Display Panel is having module dimension of 66.10 x 120.4 mm and AA size of 62.1 x 110.4 mm; it integrated driver IC ILI9881C on module, power supply for analog range 2.5v to 3.6v. This TFT module is portrait mode, if you would like to use landscape mode please contact with us for more technical support.