2.4 inch tft lcd arduino in stock

Spice up your Arduino project with a beautiful touchscreen display shield with built in microSD card connection. This TFT display is 2.4" diagonal and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. As a bonus, this display has a optional capacitive touch panel and resistive touch panel with controller XPT2046 attached by default.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

If you are looking for an inexpensive graphical interface for your Arduino, this could be it. Our 2.4″ Colour TFT display, has a four-wire resistive touch screen, a micro SD card socket, and a convenient Arduino shield footprint.

» Makerfabs is Open Hardware, Arduino, Raspberry Pi, mbed, BeagleBone, IoT, Smart Home, etc, Related Products& Services Vendor for Makers and new Startups.

The 2.4 inch TFT Touch Screen Module with micro SD card slot is now available as a SHIELD for Arduino UNO. It has a four wire resistive touch screen, a micro SD card socket, a reset switch and a convenient Arduino Uno shield footprint.

This is our 2.4 inch TFT LCD Display forArduino Uno that will spice up your Arduino project with a touchscreen display shield with built in microSD connection. This TFT display is 2.4″ diagonal with 4 white-LED backlight and 240×320 pixels. It has way more resolution than a black and white 128×64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

2.4 inch (6.1 cm) TFT Touch Screen LCD Module for Arduino has excellent vivid colour contrast. You can spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection.

This TFT display is big, bright (4 white-LED backlights) and colorful (18-bit 262,000 different shades). It has way more resolution than a black and white 128A—64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

Technical Details includes 2.4 and #x2033 diagonal LCD TFT display 240A—320 resolution, 18-bit (262,000) colour SPFD5408 controller with built-in video RAM buffer 8 bit digital interface, plus 4 control lines.It uses digital pins 5-13 and analog 0-3.

2.4 inch TFT Touch Screen LCD Module for Arduino has excellent vivid color contrast. You can Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection.

This TFT display is big,bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades).It has way more resolution than a black and white 128A—64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

Technical Details includes 2.4 and #x2033 diagonal LCD TFT display 240A—320 resolution, 18-bit (262,000) color SPFD5408 controller with built in video RAM buffer 8 bit digital interface, plus 4 control lines.It uses digital pins 5-13 and analog 0-3.

As a 2.4inch TFT display module with a resolution of 240 * 320, it uses the SPI interface for communication. LCD has an internal controller with basic functions, which can be used to draw points, lines, circles, and rectangles, and can display English, Chinese as well as pictures.

The 2.4inch LCD uses the PH2.0 8PIN interface, which can be connected to the Raspberry Pi according to the above table: (Please connect according to the pin definition table. The color of the wiring in the picture is for reference only, and the actual color shall prevail.)

The LCD supports 12-bit, 16-bit, and 18-bit input color formats per pixel, namely RGB444, RGB565, and RGB666 three color formats, this demo uses RGB565 color format, which is also a commonly used RGB format.

For most LCD controllers, the communication mode of the controller can be configured, usually with an 8080 parallel interface, three-wire SPI, four-wire SPI, and other communication methods. This LCD uses a four-wire SPI communication interface, which can greatly save the GPIO port, and the communication speed will be faster.

2. The module_init() function is automatically called in the INIT () initializer on the LCD, but the module_exit() function needs to be called by itself

Python has an image library PIL official library link, it do not need to write code from the logical layer like C, can directly call to the image library for image processing. The following will take 1.54inch LCD as an example, we provide a brief description for the demo.

This is the 2.4 inch touch screen for Arduino UNO and MEGA. It use 8-bit parallel bus, faster than serial SPI refresh , support 16-bit RGB 65K color display, display rich colors , easy to expand the experiment with SD card slot.