7-inch tft lcd capacitive touchscreen for sale

ER-TFTM070-5 is 800x480 dots 7" color tft lcd module display with RA8875 controller board,superior display quality and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO, and ARM .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 6800 8-bit,16-bit parallel,3-wire,4-wire,I2C serial spi interface.Built-in resistive touch panel controller,it"s optional for resistive touch panel,capacitive touch panel and its controller FT5206,font chip, flash chip and microsd card slot. We offer two types connection,one is pinheader and the another is ZIF connector with flat cable mounting on board by default and suggested.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for7" TFT capacitive touch shield with libraries,examples,schematic diagram for Arduino Due,Mega 2560 and Uno. For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

ER-TFTM070-6 is 1024x600 dots 7 "color tft lcd module display with RA8876 or LT7683 controller board,superior display quality and easily controlled by MCU such as 8051(C51), PIC, AVR, ARDUINO,ARM and Raspberry PI .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.Portrait mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 7 " TFT capacitive touch shield with libraries,examples,schematic diagram for Arduino Due,Mega 2560 and Uno. For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

KWH070KQ38-F04 V.2 is 7 inch LCD Display With Resistive Touch Screen with 800x480 resolution.It can be used for embedded systems, automation, GPS, medical equipment, industrial device and security equipment, etc.It is equipmed with RGB data signal interface. You also can use it with HDMI LCD Controller Board.

The 7 inch TFT Screen Display WF70QTIFGDBGB is built in with SSD1963 controller board plus a 36 pin-out connector on board. This model is available in 8080 family MPU 8bit/16bit options and already defined pin no. 33 ~ 36 as backlight supply; so there is no need to design extra backlight circuit. This display is with the module dimension of 165x100 mm and including a Projected capacitive touch screen on module.

RFF70AB2-AIH-DNG is a 7-inch TFT LCD display with capacitive touch screen. Built-in HX8264-E and HX8664-B driver ICs support 24 bit RGB interface, and also, the module has built-in DC to DC function. The contrast ratio of the module is 800:1 (typical value), the brightness is 700 nits (typical value), and the aspect ratio is 16:9. RFF70AB2 series and RFF700Y series are compatible. If you’ve already used our RFF700Y series, you can give this new RFF70AB2 series a try.

The Capacitive touch panel is activated with anything containing an inductive load such as a finger or stylus. It allows for multi-touch options. When using the capacitive touch screen, the display needs a separate controller to interface with the touch panel. The display for capacitive touch is brighter since the touch panel is transparent.

The Transmissive polarizer is best used for displays that run with the backlight on all the time. This polarizer provides the brightest backlight possible. If you have a need for a bright backlight with lower power drain, transmissive is a good choice for this TFT LCD display.

Focus LCDs can provide many accessories to go with your display. If you would like to source a connector, cable, test jig or other accessory preassembled to your LCD (or just included in the package), our team will make sure you get the items you need.Get in touch with a team member today to accessorize your display!

Focus Display Solutions (aka: Focus LCDs) offers the original purchaser who has purchased a product from the FocusLCDs.com a limited warranty that the product (including accessories in the product"s package) will be free from defects in material or workmanship.

Showcase high quality graphics and images on our 800 x 480 7” TFT display! The DT070CTFT LCD module is an upgraded version to our DT070ATFT module. Compared to the previous model, this new 7 inch display offers improved viewing angle and brighter LEDs. The DT070CTFT also uses the Himax HX8264E + HX8664B display drivers. This LCD display is available with a resistive or capacitive touchscreen panel.

7inch HDMI LCD(C) supports various systems like Raspberry Pi, Banana Pi, Banana Pro, and BB Black to provide Lubuntu, Raspbian, and Angstrom images with a high resolution of 1024×600 and a Capacitive Touch Screen. Besides, it upgrades to an IPS screen with a larger visible angle and more clear display effect. Broadly you can apply it to raspberry pi, HDMI display screen, and other mini PC or even computer displays. If you gonna use it on raspberry pi zero and BB Black, you need to buy HDMI connect wire for the use and for raspberry pi zero you also need to buy A USB type A micro cable. Matched with raspberry pi, it supports raspbian, ubuntu to do single touch without touch, and while as A PC display, it supports Windows 10 / 8.1 / 8 / 7 to do the five-point touch without drive. For the Windows 10/8.1/8 OS, the touch screen supports multi-touch up to 10 points. For some Windows 7 OS, the touch screen supports single touch only. When working with Raspberry Pi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work. When working with Beagle bone, this LCD module is used for display only so you can program the latest Angstrom image file to the board directly without any change. The BeagleBone will read the display parameters of the 7-inch HDMI displayer and set the resolution to 800*480 automatically.