oled lcd display module quotation

ER-OLED0.66-1W is the graphic OLED display module made of 64x48 individual white OLED pixels,diagonal is only 0.66 inch.The controller ic SSD1306, communicates via 8080 4-bit/8-bit parallel and I2C/4-wire serial interface,thanks to controller"s built-in voltage generation,only a single 3.3V power supply is needed. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast,extremely wide viewing angle and extremely operating temperature.The fpc is the soldering type,no need connector.Just solder the FPC on your PCB directly.

ER-OLED0.96-1YB is the graphic OLED display module made of 128x64 yellow and blue OLED pixels,diagonal is only 0.96 inch.The controller ic SSD1306, communicates via 6800/8080 8-bit parallel and I2C/3-wire/4-wire serial interface,thanks to controller"s built-in voltage generation,only a single 3.3V power supply is needed. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast,extremely wide viewing angle and extremely operating temperature.The fpc is the soldering type,no need connector.Just solder the FPC on your PCB directly.

Interested in a quote for a standard or modified product?Contact us at (847) 844-8795 or nhsales@newhavendisplay.com. You may also fill out the form below and we’ll respond to your request within 48 hours.

We often get asked, "What"s your smallest display?". Crystalfontz specializes in small displays, in fact the majority of our displays are smaller than 5". To make it easier for you to find the smallest lcd display, we"ve compiled this list of the most tiny displays we have.

This OLED display has high brightness, self-emission, high contrast ratio, slim/thin outline, wide viewing angle, a wide temperature range, and super-low power consumption.

The wide range of Bolymin displays is able to satisfy many sectors including automotive electronics, medical, security and video surveillance systems, industrial control and automation, offering solutions such as alphanumeric LCD modules, graphic modules, TFT monitors and touch.

Programmable display graphics for alphanumeric characters and animated sequences. 64 colors of backlighting can be controlled dynamically. Pushbutton switch with LCD, RGB LED backlighting.

64 colors of backlighting can be controlled dynamically. Pushbutton switch with LCD, RGB LED backlighting. Low energy. Dust-tight construction. Viewing area: 17.0mm x 13.0mm (horizontal x vertical).

Broad and even light distribution. Consistent backlighting. Low energy consumption. Programmable LCD with a variety of LED backlighting colors. Rubber dome.

Low-energy-consumption programmable LCD with a variety of LED backlighting colors. Rubber dome. High reliability and long life of one million actuations minimum.

The S0109 is a single switch, human machine interface (HMI) solution packaged in a small panel mount, pushbutton-sized display that allows for monitor and control of applications.

Part Number: IS-S04G1LC-S -- Human-Machine Interface with four programmable 64x32 LCD SmartDisplay pushbuttons that monitor and control four 7V-12V fans or lights over eight levels of speed/brightness

This attractive miniature OLED (Organic Light-Emitting Diode) display with 128x64 resolution at a 0.96-inch screen size comes in handy when you wish to add a display to your project.

This OLED display is made of 128x64 individual blue OLED pixels. As each of these pixels emits light on its own, it doesn"t need a backlight panel like the classics 2x16 LCD display. Also because of this characteristic, OLED display can produce high contrast texts/images and it"s easily readable even under bright light. It can really display tons of information despite the compact size.

This OLED display uses an SSD1306 driver chip and can be controlled via the I2C interface. Although there"s a 3.3V LDO (Low Dropout) voltage regulator built in this OLED module, SDA & SCL lines are not protected/level-shifted in any way. Hence we recommend using 3.3V only for this OLED display. Use 5V for supply and logic levels at your own risk. Otherwise, you may use any logic level converter on the IO pins for that extra safety.

The I2C address for this OLED display is 0x3C, NOT 0x78, or 0x7A as printed on the back of the OLED board. Please remember to modify the address in your code to 0x3C in order to communicate with it. This I2C address can be modified in order to interface two OLED displays by using one host device. You just need to desolder the resistor near label "0x78" and solder it back to the two pads nearest to label "0x7A" as shown below. By doing this, the I2C address of the OLED display will become 0x3D.

Warning!This modification is not recommended for beginners who have just learned how to solder as it involves SMD components and if the board is overheated, you may damage the OLED panel permanently.