raspberry pi lcd screen projects quotation

some jokes (dark jokes preferably, because I"m a horrible human being) displayed from JokeApi. I basically copied the example script and started from there.

logging.info(f"{quote},\n Font size: {size}, Line count: {line_length}, Quote height: {quote_height}, Offset: {offset_y}, Screen height: {screen_height}")

Maker Conor O"Hanlon has shared a build guide for a Raspberry Pi Zero-powered motivational message dispenser, which uses an ePaper display to keep the power draw and desk glare down.

"The Covid-19 pandemic has been hard for everyone. Why not give yourself a break and create this unique Raspberry Pi Zero project," O"Hanlon writes by way of introduction. "This motivational quote bot will display a new quote every hour. It sits on my desk and gets me through the day."

The project is built around a Pi Zero W, which includes an on-board Wi-Fi and Bluetooth radio, connected to a Waveshare 2.13" ePaper Display HAT—an add-on that connects via the Raspberry Pi"s general-purpose input/output (GPIO) port and provides a small, low-power electrophoretic display panel.

Rather than plug your Raspberry Pi into a TV, or connect via SSH (or remote desktop connections via VNC or RDP), you might have opted to purchase a Raspberry Pi touchscreen display.

Straightforward to set up, the touchscreen display has so many possibilities. But if you"ve left yours gathering dust in a drawer, there"s no way you"re going to experience the full benefits of such a useful piece of kit.

The alternative is to get it out of the drawer, hook your touchscreen display to your Raspberry Pi, and reformat the microSD card. It"s time to work on a new project -- one of these ideas should pique your interest.

Let"s start with perhaps the most obvious option. The official Raspberry Pi touchscreen display is seven inches diagonal, making it an ideal size for a photo frame. For the best results, you"ll need a wireless connection (Ethernet cables look unsightly on a mantelpiece) as well as a Raspberry Pi-compatible battery pack.

Several options are available to create a Raspberry Pi photo frame, mostly using Python code. You might opt to script your own, pulling images from a pre-populated directory. Alternatively, take a look at our guide to making your own photo frame with beautiful images and inspiring quotes. It pulls content from two Reddit channels -- images from /r/EarthPorn and quotes from /r/ShowerThoughts -- and mixes them together.

Rather than wait for the 24th century, why not bring the slick user interface found in Star Trek: The Next Generation to your Raspberry Pi today? While you won"t be able to drive a dilithium crystal powered warp drive with it, you can certainly control your smart home.

In the example above, Belkin WeMo switches and a Nest thermostat are manipulated via the Raspberry Pi, touchscreen display, and the InControlHA system with Wemo and Nest plugins. ST:TNG magic comes from an implementation of the Library Computer Access and Retrieval System (LCARS) seen in 1980s/1990s Star Trek. Coder Toby Kurien has developed an LCARS user interface for the Pi that has uses beyond home automation.

Building a carputer has long been the holy grail of technology DIYers, and the Raspberry Pi makes it far more achievable than ever before. But for the carputer to really take shape, it needs a display -- and what better than a touchscreen interface?

Setting up a Raspberry Pi carputer also requires a user interface, suitable power supply, as well as working connections to any additional hardware you employ. (This might include a mobile dongle and GPS for satnav, for instance.)

Now here is a unique use for the Pi and its touchscreen display. A compact, bench-based tool for controlling hardware on your bench (or kitchen or desk), this is a build with several purposes. It"s designed to help you get your home automation projects off the ground, but also includes support for a webcam to help you record your progress.

The idea here is simple. With just a Raspberry Pi, a webcam, and a touchscreen display -- plus a thermal printer -- you can build a versatile photo booth!

Various projects of this kind have sprung up. While the versions displayed above uses a thermal printer outputting a low-res image, you might prefer to employ a standard color photo printer. The wait will be longer, but the results better!

Projects along these lines can also benefit from better use of the touchscreen. Perhaps you could improve on this, and introduce some interesting photo effects that can be tweaked via the touchscreen prior to printing?

How about a smart mirror for your Raspberry Pi touchscreen display project? This is basically a mirror that not only shows your reflection, but also useful information. For instance, latest news and weather updates.

Naturally, a larger display would deliver the best results, but if you"re looking to get started with a smart mirror project, or develop your own from scratch, a Raspberry Pi combined with a touchscreen display is an excellent place to start.

Many existing projects are underway, and we took the time to compile six of them into a single list for your perusal. Use this as inspiration, a starting point, or just use someone else"s code to build your own information-serving smart mirror.

Want to pump some banging "toons" out of your Raspberry Pi? We"ve looked at some internet radio projects in the past, but adding in a touchscreen display changes things considerably. For a start, it"s a lot easier to find the station you want to listen to!

This example uses a much smaller Adafruit touchscreen display for the Raspberry Pi. You can get suitable results from any compatible touchscreen, however.

Alternatively, you might prefer the option to integrate your Raspberry Pi with your home audio setup. The build outlined below uses RuneAudio, a Bluetooth speaker, and your preferred audio HAT or shield.

Requiring the ProtoCentral HealthyPi HAT (a HAT is an expansion board for the Raspberry Pi) and the Windows-only Atmel software, this project results in a portable device to measure yours (or a patient"s) health.

With probes and electrodes attached, you"ll be able to observe and record thanks to visualization software on the Pi. Whether this is a system that can be adopted by the medical profession remains to be seen. We suspect it could turn out to be very useful in developing nations, or in the heart of infectious outbreaks.

We were impressed by this project over at Hackster.io, but note that there are many alternatives. Often these rely on compact LCD displays rather than the touchscreen solution.

Many home automation systems have been developed for, or ported to, the Raspberry Pi -- enough for their own list. Not all of these feature a touchscreen display, however.

One that does is the Makezine project below, that hooks up a Raspberry Pi running OpenHAB, an open source home automation system that can interface with hundreds of smart home products. Our own guide shows how you can use it to control some smart lighting. OpenHAB comes with several user interfaces. However, if they"re not your cup of tea, an LCARS UI theme is available.

Another great build, and the one we"re finishing on, is a Raspberry Pi-powered tablet computer. The idea is simple: place the Pi, the touchscreen display, and a rechargeable battery pack into a suitable case (more than likely 3D printed). You might opt to change the operating system; Raspbian Jessie with PIXEL (nor the previous desktop) isn"t really suitable as a touch-friendly interface. Happily, there are versions of Android available for the Raspberry Pi.

This is one of those projects where the electronics and the UI are straightforward. It"s really the case that can pose problems, if you don"t own a 3D printer.

The Covid-19 pandemic has been hard for everyone. Why not give yourself a break and create this unique Raspberry Pi Zero project. This motivational quote bot will display a new quote every hour. It sits on my desk and gets me through the day.

You will also need an installation of Raspberry Pi OS on your micro SD card. If you are unsure of how to do this, please read the post How to Install an OS on the Raspberry Pi.

Start by pushing your Raspberry Pi Zero into the provided case. Note: Please make sure your SD card is removed before trying to fit the Raspberry Pi into this case. Failure to do this will damage the card

If you have already have a Raspberry Pi Zero and you don’t have header pins, you will need to solder these pins to your board. Otherwise, the Waveshare e-Paper screen should fit right on top of your Raspberry Pi. Getting the screen into place inside the case can be a little tricky.Do not force the screen on the Pi as you will bend the pins

Place the cover on top of the case and push firmly into place. After this, carefully insert the micro SD card back into the Raspberry Pi. The final assembly should look like below:

Power up the Raspberry Pi. You will now need to clone my Pi-Motivator repository. This repository includes the necessary Waveshare libraries, fonts and a file named quotes.json which is used to store the quotes:

Open motivator.py in the editor of your choice. I will be using vim for this tutorial. Start by importing json, random and textwrap. You will be using these imports to load in the quotes.json file, picking a random quote and wrapping the text to make sure that it fits on the screen,

Now that you have a way to get your quote, you need to print it to the screen. Initialize the module and print a white box which covers the entire screen. This will clear the frame:

The motivational quote bot displays a new quote every hour. To do this let’s go ahead and create a while loop. When a message gets printed, you will want to draw a white rectangle first to clear the screen:

Go ahead and get a random quote by using the method created earlier. You will also want to break this text into multiple lines using textwrap.fill . In my case I chose to break after 30 characters which made the text fit the screen perfectly. Note: I am only using the message variable here but if you had a bigger screen you could use both:

Once you have your quote, print it to the screen using draw.text and epd.displayPartial. After this, sleep for 60 minutes before displaying a new quote:

And that’s it for creating this unique Raspberry Pi Zero project! As always, if you have any questions or comments please feel free to post them below. Additionally, if you run into any issues please let me know

Introducing Inkyshot: an inspirational e-ink display delivering a daily shot of encouragement through a quote or personalized message for you or your loved ones. Based on a Raspberry Pi Zero and e-ink display, Inkyshot is a perfect weekend project whether you’re completely new to IoT or an experienced developer.

Not having ever built hack projects myself, discovering and experiencing the ability to remotely deploy containers represented a whole new way for me to connect in personal relationships, which fuels the inspiration behind Inkyshot.

My sister and I share an extremely close relationship, despite living in different countries since I left home for college. Throughout the years, we’ve sent each other countless care packages, along with handwritten letters intimating the endless chats hanging out in each other’s rooms at home.

When I first saw the e-ink displays for Raspberry Pi Zero, I fell in love with it, and came up with the initial idea of this project: I wanted to send personal, encouraging messages to my sister that were more intimate than a text message, and faster than our handwritten letters. I mentioned the idea to our Hardware Hacker, Chris, who also wanted to build one for his partner living in another country. Together, we built Inkyshot: an e-ink message display that can pull an inspirational quote of the day, or send messages of your choosing.

It’s the perfect way for me to stay connected with my sister, and give her a shot of inspiration and encouragement wherever I am in the world, letting her know that I’m always thinking of her. You can also build a number of these and send them to anyone who needs some daily encouragement (scaling is easy with balena, and free for up to 10 devices)!

The links above are to vendors in the UK; if you’re in the US, Adafruit provides the InkypHAT and Raspberry Pi Zero WH, and here is a link to a Female Micro USB to DIP Adapter

The hardware set-up is pretty straightforward-- you will need a Raspberry Pi Zero WH (with WiFi and the pre-soldered header, unless you’d like to solder a header on yourself), on top of that, the InkypHAT e-ink display, and a Micro-USB power supply to power the Pi Zero. You’ll also need a solid SD card: I recommend the SanDisk ExtremePro, at least 8GB.

This can be set up in various ways depending on the case you’re using, but in either case you’ll have to solder wire from the Pi Zero onto the PCB of the adapter. Chris created a build video demonstrating and explaining how to assemble the case here.

1: The test character determines where the line breaks happen based on the width of a character. If you have an ‘l’ as a test character, it’s likely not going to fit on the screen. If you have an ‘m’ as the character, the margins will likely be too large. The default test character is ‘a,’ which seems to be a good choice of an average character width for most fonts.

And that’s it! Your Inkyshot will now display the Quote of the Day from the They Said So ® REST API, and you can now update your Inkyshot message through the balenaCloud dashboard!

Among the many things I could have built for my Hack Friday project, Inkyshot inspired me the most - it’s something that could make use of technology to create a positive impact on my relationship with my sister by keeping us connected.

Seeing it go from an idea to completion has been a magical feeling that I hope is shared by everyone who builds this project. It is my intention that Inkyshot will bring the same joy to you and your loved ones, wherever in the world they might be, and that it inspires closer connections in our most cherished relationships.

I decided to build a similar gift from scratch, using a Raspberry Pi and a custom-built wooden housing. In this post I"m going to cover both the software and hardware side of how I designed and built a custom book quote clock!

Raspberry Pi 3A+ (Due to supply chain issues this was literally the only model I could acquire in time for Christmas. I would have preferred a more powerful model but it gets the job done)

You could get by without the usb-c adapters, but I really wanted a flush-mounted USB-C port on the back of the case. More on that later. Depending on the size of the case you end up building, you may need a right-angle adapter for the micro-USB cable. There wasn"t enough space in mine above the Raspberry Pi to use a normal straight-end cable.

Thankfully, I was able to use Project Gutenberg as my content source. I downloaded a large plaintext subset of the library, containing about 60,000 books at a size of around 16 gigabytes. The gutenberg-dammit repository on GitHub was a huge help by providing plaintext copies of Project Gutenberg through 2016. Now, I needed to find the quotes I cared about. Let"s break down a particular time, say, 3:37. There are many ways to represent this time in the English language:

As I mentioned above, this is running on a Raspberry Pi 3A+ (this is the square Raspberry Pi). It"s powerful enough for running my simple web app, but it"s a bit underpowered for my liking. If I could have, I would have bought a higher end model but with supply chain shortages this was all I could get, and it still cost me $50 (about double what it should).

It"s almost 2022, and I refuse to make anything that doesn"t work with USB-C. I wanted the clock to have a detachable power cord, so I bought a few little cables and adapters so I could add a flush-mounted USB-C port to the back of the casing that powered the Raspberry Pi via its micro-USB port.

I always image my Raspberry Pi SD cards using Raspberry Pi Imager. This little open-source tool does an amazing job of simplifying the process of formatting and imaging a card to boot a Raspberry Pi from.

The touchscreen I ordered came with some drivers that needed to be installed in order to get the touch system to work. I also installed a number of other utilities. The unclutter package is used to hide the mouse after half a second, so it doesn"t show on the display. I took bits and pieces from this tutorial on pimylifeup.com, which is a great resource for various Raspberry Pi instructional articles. I didn"t follow that guide precisely, but there were some great ideas I did use.

When the Raspberry Pi boots, it automatically starts a node server to serve the NextJS app, and then launches Chromium in kiosk mode so that the web page is visible full screen automatically. The boot process is a little slow but that"s not really a big deal since I don"t expect it to be unplugged a lot. I"m using pm2 to launch the node server on boot. I"ve found this to be the most reliable way to automatically launch a node process and keep it alive indefinitely in case of crashes.

One of the problems I ran into right away is that the Raspberry Pi 3A+ doesn"t have enough memory to run the production build of the application, so I have to copy over the production build using scp. Something like this:

cd booktime && rm -rf .next && npm run build && rm -rf node_modules && cd - && scp -r booktime/ pi@192.168.4.122:times && cd booktime && npm i && cd -

I"ll break down this command quick, what it does is clean the build directory, run a production build, remove the node modules (so we don"t waste time and space copying them to the raspberry pi), copies over the build using scp, and then re-installs the local dependences so it"s all set to run another build next time.

The web server is also running on an open port on the Raspberry Pi, so a cool side effect is that I can visit the device"s local address in a web browser to see what the clock display looks like at any time.

Designing and building the housing out of wood was the task I was least confident about, and had the most room for error. I purchased some small pieces of poplar wood and got to work measuring and cutting the pieces to make the 3 individual components - the front frame, the sides, and the back cover.

Most of these pieces were cut at 45° angles save for the back panel. Everything was glued together using a strong waterproof wood glue and clamped tightly for about an hour before being sanded, starting with 120-grit sandpaper and moving all the way down to 220-grit for a smooth finish.

After the pieces dried for another hour or so, I cleaned them off and stained them with two different colors - a darker brown for the front and a red for the side and back.

I wanted a bit of a rustic look for these pieces, so to achieve that I simply put a little bit of wood glue on the surface of the wood, and once dry sanded it down so it was smooth but not fully removed, leading to the lighter patches you can see above.

To complete the main portion of the housing, I glued the front frame onto the side pieces, and after a bit of drying did another coat in the red stain across the entire thing, so that the front matches the reddish tint but still comes out much darker in color.

Now we need to finish up the back cover. This piece doesn"t go all the way to the bottom of the case, to allow for some airflow since the display and Raspberry Pi will generate a small amount of heat.

The last step for the case was to determine how to attach the back. I ended up going with two small screws so that I could remove the panel down the road if I needed access to the Raspberry Pi. This also meant I didn"t need to put the computer inside before finishing the case, which you"d have to do if you wanted to glue the back panel on. I definitely don"t recommend the gluing route, as there are various reasons you may need access to the internals for maintenance.

Even though the hardest part was over, I was still not looking forward to mounting the display inside the case - it needed to be perfectly square and there was no real way to line it up from the back. I ended up just holding it in place and repeatedly flipping it over to look at the front while it was powered on. Once it was aligned, I used some hot glue to tack it down around the corners, and then applied a generous layer of rubber cement and super glue to fasten it securely.

When attaching the back, the USB port was a little too large to fit with the Raspberry Pi in the case. I took a Dremel tool to the backside of the port and removed all the excess plastic so it was thin enough it fit inside without putting too much pressure on the cords.

Touchscreen display has so many possibilities when used with Raspberry Pi boards. Here"s a list of top 10 must try raspberry pi touchscreen display projects:

The official Raspberry Pi touchscreen display is seven inches diagonal, making it an ideal size for a photo frame. For the best results, you’ll need a wireless connection (Ethernet cables look unsightly on a mantelpiece) as well as a Raspberry Pi-compatible battery pack.

Several options are available to create a Raspberry Pi photo frame, mostly using Python code. You might opt to script your own, pulling images from a pre-populated directory. Alternatively, take a look at our guide to making your own photo frame with beautiful images and inspiring quotes. It pulls content from two Reddit channels — images from /r/EarthPorn and quotes from /r/ShowerThoughts — and mixes them together.

The idea here is simple. With just a Raspberry Pi, a webcam, and a touchscreen display — plus a thermal printer — you can build a versatile photo booth!

Various projects of this kind have sprung up. While the versions displayed above uses a thermal printer outputting a low-res image, you might prefer to employ a standard color photo printer. The wait will be longer, but the results better!

How about a smart mirror for your Raspberry Pi touchscreen display project? This is basically a mirror that not only shows your reflection, but also useful information. For instance, latest news and weather updates.

Naturally, a larger display would deliver the best results, but if you’re looking to get started with a smart mirror project, or develop your own from scratch, a Raspberry Pi combined with a touchscreen display is an excellent place to start.

Want to pump some banging “toons” out of your Raspberry Pi? We’ve looked at some internet radio projects in the past, but adding in a touchscreen display changes things considerably. For a start, it’s a lot easier to find the station you want to listen to!

This example uses a much smaller Adafruit touchscreen display for the Raspberry Pi. You can get suitable results from any compatible touchscreen, however.

Requiring the ProtoCentral HealthyPi HAT (a HAT is an expansion board for the Raspberry Pi) and the Windows-only Atmel software, this project results in a portable device to measure yours (or a patient’s) health.

With probes and electrodes attached, you’ll be able to observe and record thanks to visualization software on the Pi. Whether this is a system that can be adopted by the medical profession remains to be seen. We suspect it could turn out to be very useful in developing nations, or in the heart of infectious outbreaks.

Another great build, and the one we’re finishing on, is a Raspberry Pi-powered tablet computer. The idea is simple: place the Pi, the touchscreen display, and a rechargeable battery pack into a suitable case (more than likely 3D printed). You might opt to change the operating system; Raspbian Jessie with PIXEL (nor the previous desktop) isn’t really suitable as a touch-friendly interface. Happily, there are versions of Android available for the Raspberry Pi.

Touchscreen display has so many possibilities when used with Raspberry Pi boards. Here"s a list of top 10 must try raspberry pi touchscreen display projects:

The official Raspberry Pi touchscreen display is seven inches diagonal, making it an ideal size for a photo frame. For the best results, you’ll need a wireless connection (Ethernet cables look unsightly on a mantelpiece) as well as a Raspberry Pi-compatible battery pack.

Several options are available to create a Raspberry Pi photo frame, mostly using Python code. You might opt to script your own, pulling images from a pre-populated directory. Alternatively, take a look at our guide to making your own photo frame with beautiful images and inspiring quotes. It pulls content from two Reddit channels — images from /r/EarthPorn and quotes from /r/ShowerThoughts — and mixes them together.

The idea here is simple. With just a Raspberry Pi, a webcam, and a touchscreen display — plus a thermal printer — you can build a versatile photo booth!

Various projects of this kind have sprung up. While the versions displayed above uses a thermal printer outputting a low-res image, you might prefer to employ a standard color photo printer. The wait will be longer, but the results better!

How about a smart mirror for your Raspberry Pi touchscreen display project? This is basically a mirror that not only shows your reflection, but also useful information. For instance, latest news and weather updates.

Naturally, a larger display would deliver the best results, but if you’re looking to get started with a smart mirror project, or develop your own from scratch, a Raspberry Pi combined with a touchscreen display is an excellent place to start.

Want to pump some banging “toons” out of your Raspberry Pi? We’ve looked at some internet radio projects in the past, but adding in a touchscreen display changes things considerably. For a start, it’s a lot easier to find the station you want to listen to!

This example uses a much smaller Adafruit touchscreen display for the Raspberry Pi. You can get suitable results from any compatible touchscreen, however.

Requiring the ProtoCentral HealthyPi HAT (a HAT is an expansion board for the Raspberry Pi) and the Windows-only Atmel software, this project results in a portable device to measure yours (or a patient’s) health.

With probes and electrodes attached, you’ll be able to observe and record thanks to visualization software on the Pi. Whether this is a system that can be adopted by the medical profession remains to be seen. We suspect it could turn out to be very useful in developing nations, or in the heart of infectious outbreaks.

Another great build, and the one we’re finishing on, is a Raspberry Pi-powered tablet computer. The idea is simple: place the Pi, the touchscreen display, and a rechargeable battery pack into a suitable case (more than likely 3D printed). You might opt to change the operating system; Raspbian Jessie with PIXEL (nor the previous desktop) isn’t really suitable as a touch-friendly interface. Happily, there are versions of Android available for the Raspberry Pi.

first of all let me say that I dont have any experience with a Raspberry, Arduino etc. at all, and also dont own any equipment yet. This is more a general question to the more experienced members here, so please bear with me if this comes across as a big unfocused

I have read through a lot of post here and other forums, and I found things similar to this (I found a post about random fortune cookie quotes), but those were all a bit more focused on the coding in itself, which is not really accessible to me (i have only very basic programming knowledge, and I am not sure if I have time to learn the basics fully). I am trying to catch up on everything myself, but thought that asking my be helpful. So I just wanted to ask for opinions on the following things:

3) Is there are generally very well regarded resource for such tutorials? I have started reading the "Beginning with Raspberry Thread" here, but just in case I thought it might be good to ask.

Get a daily random inspirational quote delivered direct to your desk with Inkyshot. Build multiple Inkyshots and share the inspiration with your friends, family and loved ones ❤️

Inkyshot wants to deliver a shot of inspiration to start your day, and by default will do this at 9AM/0900 hours UTC. You can change the hour that the update will happen with the UPDATE_HOUR variable; set it anywhere from 0 to 23.

The quote api has several quote categories available. Use the QOD_CATEGORY environment variable to change the type of quote retreived. Available categories: inspire (default), management, sports, life, funny, love, art, students.

There are a few fonts built in that you can try. The default is AmaticSC, but you can use the FONT variable and set it to any of: FredokaOne, HankenGrotesk, Intuitive, SourceSerifPro, SourceSansPro, Caladea, Roboto and Grand9KPixel. You"re welcome to PR more options into the project!

When figuring out what size font to use, Inkyshot (invisibly) fills the screen with the a character to see how many will fit. You can override this by setting the TEST_CHARACTER environment variable with any wider (w) or slimmer (i) characters of your choosing to adjust this behavior.

A position is open in the rear of the case for the use of a micro USB PCB socket, allowing for direct connection of power to the back of a Raspberry Pi Zero.

We use Norwegian Meteorological Institute"s weather API to get the weather forecast of the day. Weather symbols are customized from yr.no"s repository.

I recently received a new Raspberry Piand wanted to create an Intro to Raspberry Pi project. My Pi included a 16x2 LCD display and a Wi-Pi Card so I created the Wireless Raspberry Pi Powered Joke Machine. Just press the push-buttons and the machine will look up a one-liner and scroll through it. (Admission of guilt here...I originally thought it would be neat to create a desk-toy that could display inspiring and educational famous quotes...the Joke Machine cando this, but when I found I could just as easily generate one-liners, I decided that would be more fun :-) )

This Step by Step Instructable walks you through the process of setting up a new Raspberry Pi, adding the the PiFace Control and Display LCD, the WiPi wireless and the provided python script TheQuoteMachine.py which looks up jokes and quotes on a free service called iheartquotes.com. it"ll also describe how to access your Pi without need for a keyboard or Display using VNC remote access.

A Raspberry Pi comes with "Do it Yourself Filling", that is you decide what flavor of Linux you want on it. An easy way to do this is to use a NOOBS SD card to install Linux

NOOBS stands for New Out of the Box Software. You can buy a pre-installed NOOBS SD card (what I used for this project) or download your own from http://www.raspberrypi.org/downloads.

Next I set up VNC so that I could access my Pi from my normal laptop computer. Vnc is a process that allows me to use Graphical applications without connecting any screen up to the Pi itself.  Here"s how to set it up Install vncserver by running this command on the Pi:

connect from your laptop using the ipaddress and port of the vncserver (and the password you created above) To use vnc when you don"t have a Monitor on the Pi, you can either set up the Pi so vncserver starts automatically at boot time, or connect to the pi by using ssh or winscp to log on commandline style to the Pi and start the server.

Python is already installed on the Raspberry Pi, so to run my Quote Machine script you simply need to Download the script from instructables.com (to your Raspberry Pi)

Now you can run /home/pi/bin/TheQuoteMachine.py  It will connect to the free service http://www.iheartquotes.com and display hilarious one-liners. It does this by running a URL that returns the one-liners back in straight text, splitting the text up into 16 character wide segments and then monitoring the PiFace button events that let you scroll up and down through those segments.

Button 4 is the Quit ButtonInstall Your Quote Machine in a Project Box -steps vary depending on the box you use I used a Sharpie to mark where the LCD display should be mounted on the project box

Im having an issue it might be because I don"t have the pi face installed into it yet but the code Chomd +x /home/pi/TheQuoteMachine.py it doesn"t work I tried to run it in the terminal and python0

Nice one , I was also struck with same idea to create something called "words of wisdom" with Pi. But I would rather like to use C for programming Pi. I"m using WiringPi for GPIO control , can you plase tell me is it possible to replicate that with C. Thanks0

This is a really cool idea! I like the prospect of the joke machine. I had an idea for another function. I am thinking about taking your design and making a Fortune Cookie Machine. I found this little metal fortune cookie at a bookstore and I thought it would be cool to make a device like this and attach the metal cookie thing to it and make it generate fortunes. I have not worked with a Raspberry Pi yet, but I think this would be a really cool project to start working with it, when I can spare some cash to get supplies.

thx! I"d like to see what the fortunecookie looks like. The website I get jokes from also has fortunes. You could find a thermal printer and print them out! surplus stores sometimes have them as old credit card machines. use a model a pi to save some money and store the quotes on the sd card to reduce the need for the Wii pi csrd. Good luck!0

Note: The capacitive touch function does NOT work with the latest Raspberry Pi OS - Bullseye (release date: 30th October 2021). You can revert back to Raspberry Pi OS Buster following this tutorial.

This 5" TFT touch screen display with a resolution of 800 x 480 is perfect for your Raspberry Pi boards. With DSI interface, true color display, easy installation, and space-saving design, it is a perfect touch screen monitor for your DIY and on-the-go projects! What we like about this screen is the DSI cable provides the path for both the power and data (graphic and touch sensor), no additional wiring is needed! Super neat

Note: We notice the WiFi connection on Raspberry Pi 4 Model B will be slow. However, it will still connect to WiFi AP :) Just a little more time. We believed this is due to the PCB antenna on the Raspberry Pi board, and the DSI cable is near to the Antenna; the wireless signal will be attenuated a little bit. Using the PCB Spacers (included) to increase the gap between the LCD and Raspberry Pi will help.

For instance, a Raspberry Pi 3 Model B has a higher power requirement (2.5A) and, thus, necessitates a specific power brick. It will definitely still work, but a Raspberry Pi 2 Model B

The ideal board for the job is the £9.30 or AU$14.96) for the board. To set up and connect the Raspberry Pi, you will need a short HDMI cable and a microSD card of at least 8GB.

Finally, you will need supplies to mount the Raspberry Pi, the monitor"s power supply, all the cables and the female end of the extension cord on the back of the monitor. I used two-sided mounting tape. And I used duct tape to keep the excess cord attached as tightly to the back of the monitor as possible.

Typically, there isn"t enough room to install a Raspberry Pi inside the original backplate -- unless you"re using a Pi Zero W. Even then, the excess cords and the power supply for the monitor won"t fit. The monitor will sit closer to the wall without the back cover, so it"s best to discard it.

Connect the Raspberry Pi to the HDMI port on the monitor and -- without plugging in the extension cord -- connect the power cables to both the Raspberry Pi and the monitor. Use this to figure out the best layout of all the parts to keep everything as slim as possible.

As for the picture-hanging wire, there were no decent places to connect on the Dell monitor I used, so I drilled one hole on either side of the rear bezel that held the back cover on. This is where you might have to get creative, since no two monitors are the same.

Surprisingly, this project doesn"t require any special code for the Raspberry Pi. In fact, it will be running on Raspbian OS, a Linux distribution specifically for the Raspberry Pi.

DAKboard is the web interface used to display all the information on the monitor. It can be set up from the Raspberry Pi or from a computer, phone or tablet.

Just go to dakboard.com and create an account. Then begin configuring the layout to your liking. There are five different screen configurations to choose from:Top/Bottom

The idea is that, when powered on, the Raspberry Pi will automatically boot to your DAKboard. If you want to hang the monitor vertically instead of horizontally, you will also need to rotate the display.

First, power on the Raspberry Pi, open Terminal and type in sudo raspi-config. Once in the configuration tool:Go to Boot Options > Desktop Autologin Desktop GUI and press Enter.

Next, you will want to edit the config.txt file to rotate the screen 90 degrees. In Terminal, type sudo nano /boot/config.txt and press Enter. This opens the config file in the nano text editor. Add these lines to the end of the file (without the bullet points):# Display orientation. Landscape = 0, Portrait = 1

Finally, to force the screen to stay on and automatically boot with dakboard.com loaded in Chromium, type sudo nano ~/.config/lxsession/LXDE-pi/autostart and press Enter. Inside nano, add these four lines (without the bullet points):@xset s off

Once the Raspberry Pi has fully rebooted, use a connected mouse and keyboard to log in to DAKboard. Click Login and enter your credentials. Your DAKboard should load with your previously configured settings. If you want to change anything, click the settings cog in the upper right corner of the display (move the cursor to make it appear).

Hang the monitor on the wall and you"ll have yourself a digital clock and calendar, the week"s forecast, important headlines and beautiful pictures on display all day.

DAKboard is a great way to set up a Raspberry Pi display in a hurry. It"s easy and user-friendly and it looks great. However, it has its limitations and encourages users to upgrade to Premium to unlock the best features.