tft display mega shield in stock

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.3" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 320x240 pixels with individual pixel control.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 320x240 pixels with individual pixel control.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (Due/Mega 2560). This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

This TFT 3.5 Inch LCD display support 480x320 pixel resolutions. The display uses the ILI9481 graphics controller. The module includes the 5V-3.3V power conversion circuit and no additional level conversion circuitry is required. This Module can be inserted directly into the Arduino Mega2560 Board.

TFT01 LCD is working at 3.3V voltage, it cannot be used directly on top of a standard Arduino board, so in order to make TFT01 LCD compatible for using on standard Arduino board, designed section TFT Shield, can be directly plugged into the Arduino board^^TFT01 LCD 16 can support the current mode, since there is sufficient Mega2560 IO, while using only a touch screen interface or SD card interface, like in the case of face 328S will not exist^^TFT01LCD supports 8-bit mode, can use SD card interface and touch screen interface at the same time, adopts IC voltage division, makes the TFT display more stable^^This LCD TFT01 Arduino Mega shield V 2.2 is fit for 3.2 inch TFT LCD Module; The TFT01 MEGA shield supports 16-bit mode; Because of Mega board have enough pins for using SD card and touch function at the same time^^ 3.2 inch TFT LCD Shield, Can be directly to the 3.2 "TFT on the shields, can be compatible with the Arduino

2.4″ Inch Touch Screen TFT Display Shield adds a touch up to your Arduino project with a beautiful large touchscreen display shield with built-in microSD card connection. This TFT display is big (2.4″ diagonal) bright and colorful! 240×320 pixels with individual pixel control. It has way more resolution than a black and white 128×64 display.

Begin by carefully starting the rear connector of the TFT shield onto the Arduino Mega. Go slowly and ensure that all pins are inserted correctly and are straight.

In order to use 3.2″ TFT lcd  Shield , We must have the libraries. So you can download  (UTFT Library) and (URTouch Library) install the library by extracting that zipped file in the library folder as shown below.

Specification TFT01LCD supports 8-bit mode, can use SD card interface and touch screen interface at the same time, adopts IC voltage division, makes the TFT display more stable

It provides a solution for easy connection with TFT display module in 40 pins. What you need to do is just fix this shield with Arduino MEGA 2560 and TFT LCD. Very convenient and it can avoid any wrong connections. You can drive TFT LCD with UTFT and UTouch libraries in our store.

The 3.5 inch TFT LCD Touch Display Shield for Arduino Uno is fully assembled, tested and ready to go. Add the touch display without wiring, no soldering! Simply plug it in and load up a library – you’ll have it running in under 10 minutes! Works best with any classic Arduino ATMEGA328 Board

So spice up your Arduino UNO project with a beautiful large touchscreen display shield with a built-in microSD card connection. This TFT display is big (3.5″ diagonal) bright (4 white-LED backlights) and colorful (18-bit 262,000 different shades)!

The Display comes with 480×320 pixels with individual pixel control. It has way more resolution than a black and white 128×64 display.  As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

TFT LCD Display:TFT LCD is a LCD touch screen module. It is a powerful and multifunctional module for your project. The Screen include a controller SSD1289, it’s a support 8/16bit data interface, easy to drive by many MCU like STM32, AVR and 8051. It is designed with a touch controller in it. The touch IC is XPT2046, and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

·         This TFT LCD Screen Module, 40pins interface, not just a LCD screen but include the Touch, SD card and Flash design. So it’s a powerful extension module for your project.

·         Because TFT01 LCD is working at 3.3V voltage, it cannot be used  directly on top of a standard Arduino board, so in order to make  TFT01 LCD compatible for using on standard Arduino board, designed  section TFT Shield, can be directly plugged into the Arduino board  that use TFT01 LCD module

·         TFT01 LCD 16  can support the current mode, since there is sufficient Mega2560 IO,  while using only a touch screen interface or SD card interface, like  in the case of face 328S will not exist.

·         The Mega 2560 is a microcontroller board based on the ATmega2560 .It  has 54 digital input/output pins (of which 14 can be used as PWM  outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16  MHz crystal oscillator, a USB connection, a power jack, an ICSP  header, and a reset button.

Features:TFT LCD Module; Working voltage: 3.3V, it"s not compatible with Arduino MEGA pins, so we make a shield for Arduino MEGA; With this module you can directly plug the TFT01 in the shield and stand on the Arduino MEGA board

Specification:TFT01LCD supports 8-bit mode, can use SD card interface and touch screen interface at the same time, adopts IC voltage division, makes the TFT display more stable

Application:This LCD TFT01 Arduino Mega shield V2.0 is fit for 3.2 inch , 3.2W inch , 4.3 inch , 5 inch , 7 inch TFT LCD Module; The TFT01 MEGA shield supports 16-bit mode; Because of Mega board have enough pins for using SD card and touch function at the same time