raypak pool heater lcd display for sale

To raise pH:HASA SODA ASH increasespH in swimming pools. Measure pH in swimming pool water with an accurate test kit. Ideal pH range is 7.2-7.6. When the pH is below 7.2, add HASA SODA ASH at the rate of one (1) pound per 10,000 gallons. Add HASA SODA ASH by sprinkling over the surface of the water at the deep end of the pool while filter and pump are running. Do not add more than two (2) pounds at one time. Wait 4-6 hours and retest pH. Repeat if necessary.

Discounters Pool & Spa Warehouse reserves the right to contact the customer in rare circumstances where additional shipping charges are required. If the actual shipping charge is more than the order acknowledgment, the customer will be given the opportunity to pay the additional shipping charges or cancel the order.Discounter"s Pool & Spa reserves the right to change our shipping rates prior to purchase, any changes are not refundable. Click Herefor full shipping policy.

Heater works great but the display is funky. It functions perfectly but the digits on the very top for the temperature setting are not displaying anything legible. The current temperature display below that is fine. What part do I need to see the entire display?

Hello Daryl. According to Raypak, the display is part number 013640F. LCD Display Screen Only - 013640F General installation instructions can be viewed on Youtube Raypak, Pool Heater Model C-R206A Up To CR406A LCD Attached please find the Installation and Operation Manual for the Raypak 406A Series Gas Heaters. INSTALLATION AND OPERATION MANUAL

My boiler is working well and without any issues however the digital display has begun to fail and become illegible. Is this the correct replacement for my unit? Thanks.

Hello. The Raypak Heater PCB Control Kit 013464F is a compatible replacement Main PCB for your Raypak Heater model P-M266A-EN-C. Raypak Heater PCB Control Kit - 013464F The display board only is available as Raypak part number 013640F. LCD Display Screen Only - 013640F

My pool heater it is working fine however the LCD digital display is broken and I can"t read the temperature in the LCD. Is the Display Screen - 013640F the correct replacement part to fix the issue ?

Hi Dio, We are showing that this is not the correct replacement. The proper replacement is this 017110F Board however this part has been discontinued by the manufacturer without a replacement. It might be time for a new heater, something like this Raypak 336AEN Pool Heater

I have a Raypak P-R336A-EN-Y heater (serial # is 1204140001) and can no longer read the display. All else works perfect. Will the 013640F LCD Display fix the problem or do I need to replace the entire PC board?

It could be either your display panel, board, or sensor. At this point, I would recommend giving Raypak a direct call to see if they can direct you in the best direction to fixing this.

Hello, wondering if this part will work for me. My heater no longer displays the temperature. All else works great with the heater. Appreciate your help.

Wow, thank you for your quick response! I would have thought all i needed was the display portion. That"s a big difference going from a small inexpensive part to a $300 part. Is that because of the make/model?

I believe the difference is that the one you require is both the PCB and Display where this item is just the display. For your model when replacing you have to replace both.

Hi Jim, This will work if your unit was manufactured after May of 2011. The heater’s model and serial numbers are located on the rating plate found on the inside of the unit. To locate the rating plate, first loosen the door screw. Remove the door(s), pull up and out. The rating plate will be either a gold or silver color with the Raypak logo. The serial number will have 10 digits. The date code is found in the first four digits of the serial number, for example, a unit made in April of 2001 will have the first four digits read as 0104.

Hi, DJ. Unfortunately, this LCD Display Screen - 013640F is NOT compatible with your unit if you have the original PCB. The PC Board Control IID Unit - 010253F has been discontinued for your unit.

Ok...so here is the board that is currently in our heater(see attached pic). It was replaced at some point. So...back to my original question :) any ideas on how I can get the display replaced? Thank you so much for all your time and assistance. DJ

Will this LCD display work with Model # P-M266A-EN-C S/N 1509283404? Is there any difficulty in installing this part and do I need any other parts if I replace this LCD Display? The display is barely visible but the unit is running fine.

For over 70 years, Raypak Raypak is a wholly owned subsidiary of Rheem Manufacturing and has been the world’s leading manufacturer of copper finned boilers and heaters. In 2000 Raypak’s primary manufacturing facility was relocated to a completely new 235,000 square foot building in Oxnard, California, its current headquarters. Raypak’s design goals are and have always been high quality, reliability and energy efficiency.

This is the Led Display For Raypak Digital Pool Heaters. Not Used On RP2100 Heaters, Only Digital Atmospheric Heaters, made after 2004. Fits All Sizes 206A-406A 013640F

A pool heater that runs smoothly is a pool owner"s dream. But, for some people, the output of their pool heater and temperature of their pool water remains a mystery after the LCD on their Raypak heater has broken down. Over years of use, the LCD display on any pool heater will be exposed to the sun, moisture, and harsh pool chemicals, which can cause your display to stop functioning.

If you"ve missed the ability to read the status of your pool and heater at a glance, you"ll be happy to know that replacements are available for Raypak pool heaters.

The Raypak 013640F LCD Display has been designed to provide a full replacement for the LCD Displays on Raypak RP2100 heaters (that were manufactured after 2011). This small and affordable part can bring your LCD display back to life with a fast and easy repair.

There is one thing to keep in mind for RP2100 Raypak heater owners. The 013640F Raypak 013640F LCD Display is a match only for RP2100 heaters that were manufactured after 2011. If you"re in need of a new display for an older Raypak model, the 013640F display may not be the right fit for your heater.

Raypak / Rheem Digital Heaters, Electronic Ignition (Manufactured From 05/2011) - P-R206A-EN-C, P-R206A-EP-C, P-R266A-EN-C, P-R266A-EP-C, P-R336A-EN-C, P-R336A-EP-C, P-R406A-EN-C, P-R406A-EP-C

Raypak / Rheem Digital Heaters, Electronic, Salt Water (Manufactured From 05/2011) - P-R206A-EN-X, P-R206A-EP-X, P-R266A-EN-X, P-R266A-EP-X, P-R336A-EN-X, P-R336A-EP-X, P-R406A-EN-X, P-R406A-EP-X