sainsmart 3.2 tft lcd display schematic made in china

SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

There is built-in SD card slot in the shield, so we can use it to upload images. But the images need to be converted RAW format first.You can use the tool here. SD libraries need to be preinstalled for displaying the image.

SainSmart 3.2" TFT LCD Displayis a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and multifunctional module for your project. The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

SainSmart 3.2 TFT LCD shield works in 3.3V voltage level and you need to use cables to connect with Arduino Mega. And this shield can help you out of the bothers to use other cables. You just need to plug the module to Mega through this shield.

The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2” display with 320x240 16bit color pixels and resistive touchscreen.

The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2” display with 320x240 16bit color pixels and resistive touchscreen.

ER-TFTM032-3 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card .It"s optional 3.2 " 4-wire resistive touch panel with controller XPT2046 and 3.2 " capacitive touch panel with controller FT6236 . It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

Arduino mega + 3.2" tft case. there are 2 different case bottoms, 1 without a hole and 1 with. both cases have a cutout for powering the Mega from a USB.

I designed this to dress up a project that used the SainSmart LCD Keypad Shield with and Arduino. The bezel itself prints pretty easily with very little support structure needed. The buttons are designed to be self-captivating (they just push in and...

I didn"t have a 3.5" TFT screen, but I did have the 3.2" ones (at the time the 3.5" were on backorder and I got impatient). This fits my 3.2" TFT perfectly. ... My unit comes from 4D Systems as well.

This top surface has 4 additional holes (for screwing to the bezel) and a square cut out of it to fit the LCD circuit board (see attached photo above) The bezel has 4 screw holes that line up with laser cut holes in the laser cut back plate. the...

Support piece for SainSmart kit: http://www.sainsmart.com/sainsmart-mega2560-board-3-5-tft-lcd-module-display-shield-kit-for-atmel-atmega-avr-16au-atmega8u2.html When both the shields are stacked, they are kind of flappy. This part fits on one end...

accurate CAD model of UPC "6013801500024" from the SainSmart Raspberry Pi 3 Model B Ultimate Kit with 5 inch LCD (Red&White Case)https://smile.amazon.com/gp/product/B01FHEBIE0/

A (very) compatible 800x480 LCD is available, but it"s 5 inch big and so the original bezel won"t fit. I also didn"t like the idea of sticking LCD to PCB by a piece of double sided tape. Here"s my original post about hacking it in:(pocket)CHIP with...

The cable canal lid I used had a thickness of 1.5mm. How to assemble it: Bezel -> Cable canal lid -> Display Cut a rectangle for the whole display without the PCB inside...

I bought a 4.3" TFT LCD Color Monitor off eBay for a reverse camera I installed in my car and had nothing to mount it to my car with. Monitor dimensions were 120mm(L) x 75mm(W) x 15mm(H) and this seemed to fit quite snugly. I have only created a...

This is a sipmple box/case for Arduino Uno and 2.4"" TFT Lcd Touch Screen. There are 2 kind of cases: closed or with open grooves for refrigeration. Originally made for a mini - meteo station, it can be customizable with FreeCad file. ...It was made...

A small mountable holder for a fasttech LCD module. Mounting pins are a little tight but can be snapped off if not needed. Mount holes are designed for assorted leg or spacer designs. Holes are 5mm dia, 34mm apart and hole centre 5.5mm from edge if...

I just redesigned it so it can house cheap chinese 2.4" TFT touchscreen, instead of hard to find and expensive 2.8". No support is needed for any of parts.

This is an update to the FreeTouchDeck case by Dustin Watts that holds a 3.2" TFT display since I bought a different size than Dustin used. I modified the Top_for_TFT_with_Headers.stl file. I"ve also uploaded the Fusion 360 file....

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

LCD screen bezel for Oneplus 2. If not only your screen is destroyed, but also the black plastic frame surrounding it (see picture), you can try your luck by printing this bezel and installing it. Replacement screens do not come with this bezel,...

This 7.0" TFT LCD Module can be easy controlled by MCU such as 8051, PIC, AVR, ARDUINO, and ARM .It can be used in any embedded systems which require display high quality colorful image. The Module used SSD1963 LCD controller with 5 inch LCD module with touchpad. This LCD has a superior display quality and super wide viewing angle. The LCD has a SD slot, SPI flash footprint.

I am sure that many people are trying to make their Raspis to display video to a nonHDMI/nonCOmposite LCD screen using its SPI port, so I hope this thread will help all of us seeking expertise with the SSD1289 controller.

LCD Screens with SSD1289 controller sold in eBay for less than 10$. They include a touch screen film and an SD card reader. For the video, the screen needs 16pins for 16bits of data + 4-5 controll pins.

The problem with pi, is that its SPI does not offer that many GPIOs to "talk" to the screen using parallel mode. Although SSD1289 controller supports serial mode/interface, the LCD screen does not offer this capability. But this guy here: http://spritesmods.com/?art=spitft&page=1 made a nice schematic using a counter and 3 shift registers to get a parallel interface out of a serial. He also gives a kernel patch to enable the ssd1289 driver to use his hardware implementation but unfortunately he made it for Carambola linux platform. His patches include an ssd1289 driver he made from scratch, KConfig patch for adding his shift-registers hardware support to kernel and modifications to the SPI module of carambola.

Carambola"s patch includes patch for drivers/video/Kconfig and drivers/video/Makefile that I think can be applied easily to Raspi. Then the menuconfig will display an option to select native I/O or the shift registered hardware version.

Anyway, I will try to debug the SPI and the schematic and will post when I have more news. I am trying to find a way to read the data sent from raspi"s SPI to check if the commands for screen init and command data are correct.

So basically the display i posted as the link would work, as it is almost identical to the spritesmods.com one right?? Have you been able to display anything on your display? and would the touch module also work fine with the Pi?

Thats correct, the driver sends 3bytes of display data and one dummy byte (32 bits/32cycles) then the strobe, CS is going high (inactive). But on the next cycle it goes low (active). So CS would remain low (active) for 32 cycles (1 display command). The 4094s keep their state after the strobe so the screen reads it while CS is low.

when you connect the raspi to the power SPI /CS goes HIGH this causes reset of 4020 and its Q5 goes LOW. It is not correct situation for the LCD. You can"t keep it"s /CS LOW forever.

I totally agree with you, the schematic would be correct if /CS was active (low) for the moment the data was feeded on the screen - as you said that can be done using a inverter for Q5.

I am afraid that the person that sent me the screen from china (ebay) sent screen with other chip than SSD1289. The only thing that I managed to display on screen was a full pale blue colour.

I have order a screen like the one you (and sprite mods) use as I suspect my screen is a bit different than yours. I will try your configuration when you upload your schematic with the old screen.

It is a bit different than the one valdodov uses (it has 40 pins, incudes an SD card slot, etc). Also my screen does not have the pinout printed on the back. I tried to contact the guy from ebay so he may could send me / hep me with the pinout but without success. I assumed that the pinout would be the same as SSD1289 datasheet or the 40pins schematics I ve found on the internet.

Anyway, I think there is something wrong with my display because I haven"t succeeded to display something on the screen, not even a corrupted desktop display as valdodov had on a previous post.

3.2"inch TFT LCD Module Display Power than SainSmart w/Capacitive Touch,Tutorial. It"s optional for font chip, flash chip and microsd card. Lanscape mode is also available. 3.2"TFT LCD Display with Breakout Boardand with Capacitive Touch Panel. 3.2"TFT LCD Display with Breakout Board andwith Resistive Touch Panel. Description E R-TFTM032-3 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image. I t supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in optional microSD card slot, optional 3.2 inch 4-wire resistive touch panel with controller XPT2046 an d 3.2 inch capacitive touch panel with controller FT6236 . It"s optional for font chip, flash chip and microsd card. W e offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available. O f course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.3D drawing is available. 3.2 inch Series TFT Display L ist ↓ Display Part Number Description ER-TFT032-2(RTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ILI9320 and Resistive Touch Panel ER-TFT032-3.1(RTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ILI9341 and Resistive Touch Panel ER-TFT032-3.1(CTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ILI9341 and Capacitive Touch Panel ER-TFT032A3-3(RTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ST7789V and Resistive Touch Panel ER-TFT032A3-3(CTP) 3.2" TFT LCD 240x320 Pixels Display with Controller ic ST7789V and Capacitive Touch Panel ER-TFTM032-3(RTP) 3.2"TFT LCD Display with Breakout Board and with Resistive Touch Panel ER-TFTM032-3CTP) 3.2"TFT LCD Display with Breakout Board and with Capacitive Touch Panel W hat"s inc luded in the package ↓ Num Accessory Name Qty 1 3.2 inch TFT Display with Breakout Board 1 2 3.2" Capacitive Touch Pane l with controller FT6236 1 * The touch panel is attached on the display by default. * We default pin header connection , 5V power supply and 4-wire serial interface .Please send message if you want FFC connection , 3.3V power supply and other interface , or buy from our own store [link removed by eBay] . O ptional Accessory List (Click the part number to buy accessories) ↓ Category Part Number Description Flash Chip W25Q128FVSG WINBOND (P/N:25Q128FVSG) 128M Bit Flash Chip MicroSD Card ER3297 New Original MicroSD (TF) 1GB Memory Card Font 1 ER3300-1 15X16 dots fonts chip,it supports Chinese,Japanese(compatible with Unicode) and 150 countries character Font 2 ER3301-1 11X12,15X16 dots fonts chip, it supports Chinese,ASCII and 150 countries character Font 3 ER3303-1 11X12 , 15X16 , 24X24 dots Chinese font, It supports GB2312,GB12345 and ASCII character, also compatible with Unicode Font 4 ER3304-1 12x12,16x16,24x24,32x32 dot matrix Chinese font, supporting GB2312 Simplified Chinese and ASCII * If choose the above accessories,we"ll mount on display by default except the flash chip. Ebay doesn"t allow listings to contain external links,so the documents link may be invalid. Please copy the below entire link to your browser for checking our documents(at the bottom of the page) or for bulk order. https://www.buydisplay.com/default/3-2-inch-capacitive-touchscreen-240x320-tft-lcd-module-display D atasheet - TFT LCD Display,Controller,Connector ↓ Format Documents Name (Downloadable) Version Language Update Date Size 3.2 inch 240x320 Dots Display with Adaptor Board Datasheet 2.0 English Jan-09-2016 709K Controller ILI9341 Datasheet 1.0 English Jul-02-2013 3.2M 40 Pins 1.00mm Pitch ZIF Connector Drawing 1.0 English Apr-19-2013 268K Datasheet - Touch Panel with its Controller IC,Connector ↓ Format Documents Name (Downloadable) Version Language Update Date Size Resistive Touch Panel Controller XPT2046 Datasheet 1.0 English May-08-2007 579K 3.2 inch Capacitive Touch Panel Outline Drawing 1.0 English Dec-02-2015 254K Capacitive Touch Panel Controller FT6236 Datasheet 1.0 English Jul-24-2014 674K Datasheet for Flash Memory,MicroSD Card Slot ↓ Format Documents Name (Downloadable) Version Language Update Date Size 128M-BIT Flash W25Q128FV Datasheet 1.0 English Oct-01-2012 1.0M MicoSD Card Slot Drawing 1.0 English Dec-12-2013 1.2M Datasheet for Font Chip ↓ Format Documents Name (Downloadable) Version Language Update Date Size Summary for Font Chip 1.0 English Aug-07-2013 133K ER3300-1 Datasheet 1.0 English May-08-2010 621K ER3301-1 Datasheet 1.0 English Mar-27-2014 2.0M ER3303-1 Datasheet 1.0 English Oct-01-2013 688K ER3304-1 Datasheet 1.0 English Apr-12-2013 935K T utorial - 8051 Microcontroller Demo Code,Interfacing,Development Board&Kit ↓ Format Documents Name (Downloadable) Version Language Update Date Size 3-Wire SPI,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 180K 4-Wire SPI,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 180K 8080 8-Bit,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 179K 8080 16-Bit,Touch Panel,Font Chip,Flash,MicroSD Demo Code 1.0 English Nov-28-2014 179K ER-TFTM032-3 Interfacing Document 1.0 English Aug-2014-23 176K 8051 Microcontroller Development Board & Kit for ER-TFTM032-3 N/A N/A N/A N/A Specification Gross Weight (kg)0.0760 ManufacturerEastRising Continuity SupplyWe promise the long term continuity supply for this product no less than 10 years since 2015. Part NumberER-TFTM032-3 Display Format240x320 Dots Interface8080 8-bit Parallel , 8080 16-bit Parallel , 3-Wire Serial SPI, 4-Wire Serial SPI IC or EquivalentILI9341 AppearanceRGB on Black Diagonal Size3.2” ConnectionPin Header, FFC-Connector Outline Dimension64.9W)x89.4(H)mm Visual Area48.60x64.80mm Active Area48.60(W)x64.80(H)mm Character SizeNo Dot (Pixel) SizeNo Dot (Pixel) Pitch0.2025x0.2025 IC PackageSMT Display TypeTFT-LCD Color Touch Panel OptionalYes Sunlight ReadableNo Response Time(Typ)25ms Contrast Ratio(Typ)500:1 Colors65K/262K Viewing Direction12:00 Viewing Angle RangeLeft:60.0 , Right:60.0 , Up:50.0 , Down:50.0 degree Brightness(Typ)280cd/m2 Backlight ColorWhite Color Backlight Current (Typ)120mA Power Supply(Typ)3.3V, 5V Supply Current for LCM(Max)130mA (Vdd=3.3V) 150mA (Vdd=5V) Operating Temperature-20℃~70℃ Storage Temperature-30℃~80℃ Series NumberER-TFT032-3 About Us We"re China-based global display manufacturer named EastRising Technology Co.,Ltd. that has a worldwide business in design, produce and sell various displays for small to large companies since 2003. Our web site is [link removed by eBay] . Link for video and image of our production line and equipment. RoHS reports for all material we used on display module. Long Term Continuity Supply Warranty We promise the long terms continuity supply and would never end.Some controller IC may stop the production,we"ll try our efforts to find the completely compatible ones.If the equivalent is unavailable, we¡¯ll make the new tooling and use the most similar IC as replacement.So you don"t have to worry even your research time is very long. Shipping Policy All products will be checked carefully and packed in good condition before shipping.We e-mail all customers with tracking information immediately after the shipment for status tracking. Item will be shipped within 1 business day after the payment has been received. Customs fees and import duties for exports are buyer"s responsibility. Warranty All products are covered under our limited warranty, which provides all products are free of functional defects for a period of one year from the date of receipt and all products are free of visual defects and missing parts for a period of 30 days from the date of receipt.If a product was damaged during shipping or the order is incorrect,you must notify us within 2 days of receipt. How to return a product First request an RMA number from our sales with the information:part number,reason for return,order number. Our sales will then either issue an RMA number, ask you for more information, or offer to help you resolve a technical problem so that the product does not need to be returned. Products must arrive here in the same condition as when you received them. You are responsible for return shipping and insurance.Please make sure your RMA number is on the shipping label and on any documents you include with the product. After we receive the product, we inspect it to determine the cause of any defect, then update by email with our findings. This process usually takes five business days.

The TFT display is a kind of LCD that is connected to each pixel using a transistor and it features low current consumption, high-quality, high-resolution and backlight. This 2.8-inch full color LCD has a narrow PCB display. The resolution is 320×280 pixels and it has a four-wire SPI interface and white backlight.