240x240 wide angle tft lcd display with microsd brands

It"s only 1.5" diagonal but has a high density 220 ppi, 240x240 pixel display with full-angle viewing. It looks a lot like our 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. We"ve seen displays of this caliber used in smartwatches and small electronic devices but they"ve always been MIPI interface. Finally, Adafruit found one that is SPI and has a friendly display driver, so it works with any and all microcontrollers or microcomputers!

This lovely little display breakout is the best way to add a small, colorful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.54" display has 240x240 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well.

Our breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. We also had a little space so we placed a microSD card holder so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card. The microSD card is not included.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as example code and a wiring tutorial. The code is written for Arduino but can be easily ported to your favorite microcontroller!

Adafruit has been looking for a display like this for a long time - it"s only 1.5" diagonal but has a high density 220 ppi, 240x240 pixel display with full-angle viewing. It looks a lot like their 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. Displays of this caliber are used in smartwatches and small electronic devices but they"ve always been MIPI interface. Finally, Adafruit has found one that is SPI and has a friendly display driver, so it works with any and all microcontrollers or microcomputers!

This lovely little display breakout is the best way to add a small, colorful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.54" display has 240x240 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well.

This breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. They also had a little space so they placed a microSD card holder so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card. The microSD card is not included, but you can pick one up here.

Of course, Adafruit wouldn"t just leave you with a datasheet and a "good luck!" - they"ve written a full open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as example code and a wiring tutorial. The code is written for Arduino but can be easily ported to your favorite microcontroller!

We"ve been looking for a screen like this for a long time - it only has a 1.5" diagonal but has a high density of 220 ppi, 240x240 pixels with a wide angle display. It looks a lot like our 1.44" 128x128 screen, but it has 4x more pixels and it looks great from any angle. We have seen displays of this calibre used in smart watches and small electronic devices, but they have always been a MIPI interface. Finally, we found one that is SPI compatible and has a user-friendly display driver, so it works with all microcontrollers or microcomputers!

This pretty little display card is the best way to add a small colorful and very bright screen to any project. As the display uses 4 SPI wires to communicate and has its own addressable frame buffer per pixel, it can be used with any type of microcontroller. Even a very small one with little memory and few pins available! The 1.54" screen has 240x240 16-bit color pixels and is an IPS screen, so the color is very beautiful up to 80 degrees relative to the axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well.

Our breakout has a soldered TFT display (it uses a delicate flexible circuit connector) as well as a 3.3V regulator with very low voltage drop and a 3/5V level adapter so you can use it with 3.3V or 5V power and logic. We also had some space, so we placed a microSD card holder so you could easily load color bitmaps from a microSD card formatted FAT16/FAT32. The microSD card is not included.

Of course, we won"t just leave you a technical sheet and a "good luck"! We have a complete open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as a sample code and wiring tutorial. The code is written for Arduino but can be easily ported to your favorite microcontroller!

We"ve been looking for a display like this for a long time - it"s so small only 1.3" diagonal but has a high density 260 ppi, 240x240 pixel display with full-angle viewing.

It looks a lot like the 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. We"ve seen displays of this caliber used in smartwatches and small electronic devices but they"ve always been MIPI interface. Finally, we found one that is SPI and has a friendly display driver, so it works with any and all microcontrollers or microcomputers!

This lovely little display breakout is the best way to add a small, colorful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.3" display has 240x240 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well.

This breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. There was a little space so Adafruit placed a microSD card holder so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card. The microSD card is not included

We"ve been looking for a display like this for a long time - it"s only 1.5" diagonal but has a high density 220 ppi, 240x240 pixel display with full-angle viewing. It looks a lot like our 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. We"ve seen displays of this caliber used in smartwatches and small electronic devices but they"ve always been MIPI interface. Finally, we found one that is SPI and has a friendly display driver, so it works with any and all microcontrollers or microcomputers!

This lovely little display breakout is the best way to add a small, colorful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.54" display has 240x240 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well.

Our breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. We also had a little space so we placed a microSD card holder so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card. The microSD card is not included, but you can pick one up here.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as example code and a wiring tutorial. The code is written for Arduino but can be easily ported to your favorite microcontroller!

We"ve been looking for a display like this for a long time - it"s so small only 1.3" diagonal but has a high density 260 ppi, 240x240 pixel display with full-angle viewing. It looks a lot like our 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. We"ve seen displays of this caliber used in smartwatches and small electronic devices but they"ve always been MIPI interface. Finally, we found one that is SPI and has a friendly display driver, so it works with any and all microcontrollers or microcomputers!

This lovely little display breakout is the best way to add a small, colorful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.3" display has 240x240 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and our Arduino library supports it well.

Our breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. We also had a little space so we placed a microSD card holder so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card. The microSD card is not included, but you can pick one up here.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - Adafruit"s written a full open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as example code and a wiring tutorial. The code is written for Arduino but can be easily ported to your favorite microcontroller!

This little display is only 1.5" diagonal but has a high density of 220 PPI, 240x240 pixel display with full-angle viewing. It looks a lot like a 1.44" 128x128 display, but has 4x as many pixels and looks great at any angle. We"ve seen displays of this calibre used in smartwatches and small electronic devices but they"ve always been MIPI interfaces. Finally, we found one that is SPI and has a friendly display driver, so it works with any and all microcontrollers or microcomputers!

This lovely little display breakout is the best way to add a small, colourful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.54" display has 240x240 16-bit full colour pixels and is an IPS display, so the colour looks great up to 80 degrees off axis in any direction. The TFT driver (ST7789) is very similar to the popular ST7735, and the Arduino library supports it well.

The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. We also had a little space so we placed a microSD card holder so you can easily load full colour bitmaps from a FAT16/FAT32 formatted microSD card.

You can also share projects in various ways. You can submit a read-only copy and the person you shared the project with can order directly on our website. For more details, go to your projects and click the “Share Project” link.

Alternatively, you can upload the product list (BOM): upload an Excel, CSV or tab-delimited file, with the title or product code and the desired quantity. You will find the example file on the dedicated page.

The Adafruit TFT display has a diagonal of 1.5 "and with its 240 x 240 pixels delivers a high pixel density of 220 ppi. It is similar to the Adafruit 1.44 “128x128 TFT, but has four times as many pixels and can be easily read from any angle. Communication with the display takes place via SPI and is suitable for all microcontrollers. Thanks to the integrated framebuffer, it can also be used with small, low-performance microcontrollers. It is a 1.54 “display with a 16-bit color spectrum and a resolution of 240 x 240 pixels. Since it is an IPS display, it can be easily read in any direction up to a viewing angle of 80˚. A ST7789 is used as the TFT driver, which is very similar to the popular ST7735 and is also supported by the Arduino library. With the existing level conversion, the Adafruit.

As one of Adafruit"s top global resellers, the team at Chicago Electronic Distributors provides high-performance components and accessories from one of the industry’s most trusted brands. Our catalog of Adafruit accessories & tools provide our customers with unique options for their DIY electronics projects. We carry a variety of PCB’s, displays, breakout boards and more to give you the ability to think creatively and innovate to get your project done. If you have any question about our Adafruit accessories or products, contact the team at Chicago Electronic Distributors and we will provide you the expertise and support you need.