connect tft display to arduino quotation

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

For this tutorial I composed three examples. The first example is distance measurement using ultrasonic sensor. The output from the sensor, or the distance is printed on the screen and using the touch screen we can select the units, either centimeters or inches.

The next example is controlling an RGB LED using these three RGB sliders. For example if we start to slide the blue slider, the LED will light up in blue and increase the light as we would go to the maximum value. So the sliders can move from 0 to 255 and with their combination we can set any color to the RGB LED,  but just keep in mind that the LED cannot represent the colors that much accurate.

The third example is a game. Actually it’s a replica of the popular Flappy Bird game for smartphones. We can play the game using the push button or even using the touch screen itself.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

Next we need to define the fonts that are coming with the libraries and also define some variables needed for the program. In the setup section we need to initiate the screen and the touch, define the pin modes for the connected sensor, the led and the button, and initially call the drawHomeSreen() custom function, which will draw the home screen of the program.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

Next is the distance sensor button. First we need to set the color and then using the fillRoundRect() function we will draw the rounded rectangle. Then we will set the color back to white and using the drawRoundRect() function we will draw another rounded rectangle on top of the previous one, but this one will be without a fill so the overall appearance of the button looks like it has a frame. On top of the button we will print the text using the big font and the same background color as the fill of the button. The same procedure goes for the two other buttons.

Now we need to make the buttons functional so that when we press them they would send us to the appropriate example. In the setup section we set the character ‘0’ to the currentPage variable, which will indicate that we are at the home screen. So if that’s true, and if we press on the screen this if statement would become true and using these lines here we will get the X and Y coordinates where the screen has been pressed. If that’s the area that covers the first button we will call the drawDistanceSensor() custom function which will activate the distance sensor example. Also we will set the character ‘1’ to the variable currentPage which will indicate that we are at the first example. The drawFrame() custom function is used for highlighting the button when it’s pressed. The same procedure goes for the two other buttons.

getDistance(); // Gets distance from the sensor and this function is repeatedly called while we are at the first example in order to print the lasest results from the distance sensor

So the drawDistanceSensor() custom function needs to be called only once when the button is pressed in order to draw all the graphics of this example in similar way as we described for the home screen. However, the getDistance() custom function needs to be called repeatedly in order to print the latest results of the distance measured by the sensor.

Here’s that function which uses the ultrasonic sensor to calculate the distance and print the values with SevenSegNum font in green color, either in centimeters or inches. If you need more details how the ultrasonic sensor works you can check my particular tutorialfor that. Back in the loop section we can see what happens when we press the select unit buttons as well as the back button.

Ok next is the RGB LED Control example. If we press the second button, the drawLedControl() custom function will be called only once for drawing the graphic of that example and the setLedColor() custom function will be repeatedly called. In this function we use the touch screen to set the values of the 3 sliders from 0 to 255. With the if statements we confine the area of each slider and get the X value of the slider. So the values of the X coordinate of each slider are from 38 to 310 pixels and we need to map these values into values from 0 to 255 which will be used as a PWM signal for lighting up the LED. If you need more details how the RGB LED works you can check my particular tutorialfor that. The rest of the code in this custom function is for drawing the sliders. Back in the loop section we only have the back button which also turns off the LED when pressed.

In order the code to work and compile you will have to include an addition “.c” file in the same directory with the Arduino sketch. This file is for the third game example and it’s a bitmap of the bird. For more details how this part of the code work  you can check my particular tutorial. Here you can download that file:

getDistance(); // Gets distance from the sensor and this function is repeatedly called while we are at the first example in order to print the lasest results from the distance sensor

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

I have this 2.4" TFT LCD with SPFD5408 controller http://www.banggood.com/2_4-Inch-TFT-LCD-Shield-Touch-Board-Display-Module-For-Arduino-UNO-p-940735.html.

Beside that, my entirely brand new (Arduino) Uno R3 from eBay seems to be not working now (it has been powered from USB and only the LCD shield has been connected, have had it for 2 hours until now).

1st Arduino project, beyond the very basic intros, and no coding experience before this endeavor, so I"m sure I"m just not searching the right things/way to figure this out.

The project - replacing gauges in my truck with Arduino+TFT display. As a starter, I"m working strictly on single fuel gauge functionality, and eventually including dual fuel gauges (2 separate fuel tanks in truck), voltage gauge, coolant temp gauge, and GPS driven speedometer. Yeah...I"m already realizing I"m in for a bit of a steep learning curve here, lol.

The setup - Genuine Arduino Mega 2560, Seeed Studio 2.8" touchscreen sheild V1.0, aftermarket universal style fuel sender. Sender is connected to Analog pin 9 through a voltage divider circuit running roughly 1.5VDC-4.95VDC, and I get appropriate numbers from the serial monitor when cycling the sender. I"m not currently utilizing the touch features of the screen, though I may in the future. RIght now it"s strictly a display device. I did find out how to modify the TFT.h file to get the display to function on the Mega board, and am writing static text to it currently.

The problem - how the heck do I get the value read from the Analog pin to display on the screen? I"ve spent the last couple of days searching the forums here and on Adafruit, as well as various other sites found on Google. I"ve spent hours looking at other"s code to try and figure this out, but not being a coder before this, I"m finding it difficult to determine which parts of the code are relevant to what I"m attempting to do, and I think I may be confusing myself/WAY overthinking it, lol. It seems like it should be a simple thing...

This is my current code. I started with the Draw Text example sketch, and modified it for my use. dTankPin is the variable I set for the driver"s side fuel tank, with dLevel being the variable set to store the reading I get from the sender. I set static text lines for Tank - D, Tank - P (driver and passenger side fuel tanks), Volts, and C/T (coolant temp), then MPH for the future GPS speedometer. The commented out lines in there are just static values I added to initially set font size to fit the screen, but that I want to replace with the dynamic values i get from reading the various sensors.

That part I"m good with, but I can"t figure out how to get a value read from the analog pins to display as numbers on the screen. I"m not looking to be spoon fed the answers, but if I could maybe get some guidance on what functions I"m missing, or what I should be searching for to figure this out?

//Below sets up the SoftwareSerial ports so that the arduino can receive information from the MPPT Controller aswell as pass its information through to the hardware UART

from what i can gather, i may need to change it from a srting to an INT or a CHAR, but all the examples i have tried and just guessed out of hope have failed.

Now learning arduino tft, got a cheap 1.8 tft spi display from ebay, trying the arduino TFTDsiplayText example with potentiometer, and all my "goal" is the white screen.

were missing for my display (hailege, 2,8 tft, spi, il9431, https://www.amazon.de/-/en/gp/product/B07YTWRZGR/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1). so it might just be that the led backlight isnt being turned on. but of course the tip might not help with the st7796s.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

Displays are one of the best ways to provide feedback to users of a particular device or project and often the bigger the display, the better. For today’s tutorial, we will look on how to use the relatively big, low cost, ILI9481 based, 3.5″ Color TFT display with Arduino.

This 3.5″ color TFT display as mentioned above, is based on the ILI9481 TFT display driver. The module offers a resolution of 480×320 pixels and comes with an SD card slot through which an SD card loaded with graphics and UI can be attached to the display. The module is also pre-soldered with pins for easy mount (like a shield) on either of the Arduino Mega and Uno, which is nice since there are not many big TFT displays that work with the Arduino Uno.

The module is compatible with either of the Arduino Uno or the Arduino Mega, so feel free to choose between them or test with both. As usual, these components can be bought via the links attached to them.

One of the good things about this module is the ease with which it can be connected to either of the Arduino Mega or Uno. For this tutorial, we will use the Arduino Uno, since the module comes as a shield with pins soldered to match the Uno’s pinout. All we need to do is snap it onto the top of the Arduino Uno as shown in the image below, thus no wiring required.

This ease of using the module mentioned above is, however, one of the few downsides of the display. If we do not use the attached SD card slot, we will be left with 6 digital and one analog pin as the module use the majority of the Arduino pins. When we use the SD card part of the display, we will be left with just 2 digital and one analog pin which at times limits the kind of project in which we can use this display. This is one of the reasons while the compatibility of this display with the Arduino Mega is such a good news, as the “Mega” offers more digital and analog pins to work with, so when you need extra pins, and size is not an issue, use the Mega.

To easily write code to use this display, we will use the GFX and TFT LCD libraries from “Adafruit” which can be downloaded here. With the library installed we can easily navigate through the examples that come with it and upload them to our setup to see the display in action. By studying these examples, one could easily learn how to use this display. However, I have compiled some of the most important functions for the display of text and graphics into an Arduino sketch for the sake of this tutorial. The complete sketch is attached in a zip file under the download section of this tutorial.

As usual, we will do a quick run through of the code and we start by including the libraries which we will use for the project, in this case, the Adafruit GFX and TFT LCD libraries.

With this done, the Void Setup() function is next. We start the function by issuing atft.reset() command to reset the LCD to default configurations. Next, we specify the type of the LCD we are using via the LCD.begin function and set the rotation of the TFT as desired. We proceed to fill the screen with different colors and display different kind of text using diverse color (via the tft.SetTextColor() function) and font size (via the tft.setTextSize() function).

Next is the void loop() function. Here we basically create a UI to display the youtube subscribe button, using some of the same functions we used under the void setup() function.

The Adafruit library helps reduce the amount of work one needs to do while developing the code for this display, leaving the quality of the user interface to the limitations of the creativity and imagination of the person writing the code.

That’s it for this tutorial guys, thanks for reading. If you made some cool projects based on this or you just want to ask questions about this tutorial, feel free to reach out via the comment section below.

Hi guys, welcome to today’s tutorial. Today, we will look on how to use the 1.8″ ST7735  colored TFT display with Arduino. The past few tutorials have been focused on how to use the Nokia 5110 LCD display extensively but there will be a time when we will need to use a colored display or something bigger with additional features, that’s where the 1.8″ ST7735 TFT display comes in.

The ST7735 TFT display is a 1.8″ display with a resolution of 128×160 pixels and can display a wide range of colors ( full 18-bit color, 262,144 shades!). The display uses the SPI protocol for communication and has its own pixel-addressable frame buffer which means it can be used with all kinds of microcontroller and you only need 4 i/o pins. To complement the display, it also comes with an SD card slot on which colored bitmaps can be loaded and easily displayed on the screen.

The schematics for this project is fairly easy as the only thing we will be connecting to the Arduino is the display. Connect the display to the Arduino as shown in the schematics below.

Due to variation in display pin out from different manufacturers and for clarity, the pin connection between the Arduino and the TFT display is mapped out below:

We will use two libraries from Adafruit to help us easily communicate with the LCD. The libraries include the Adafruit GFX library which can be downloaded here and the Adafruit ST7735 Library which can be downloaded here.

We will use two example sketches to demonstrate the use of the ST7735 TFT display. The first example is the lightweight TFT Display text example sketch from the Adafruit TFT examples. It can be accessed by going to examples -> TFT -> Arduino -> TFTDisplaytext. This example displays the analog value of pin A0 on the display. It is one of the easiest examples that can be used to demonstrate the ability of this display.

The second example is the graphics test example from the more capable and heavier Adafruit ST7735 Arduino library. I will explain this particular example as it features the use of the display for diverse purposes including the display of text and “animated” graphics. With the Adafruit ST7735 library installed, this example can be accessed by going to examples -> Adafruit ST7735 library -> graphics test.

The first thing, as usual, is to include the libraries to be used after which we declare the pins on the Arduino to which our LCD pins are connected to. We also make a slight change to the code setting reset pin as pin 8 and DC pin as pin 9 to match our schematics.

Next, we create an object of the library with the pins to which the LCD is connected on the Arduino as parameters. There are two options for this, feel free to choose the most preferred.

Next, we move to the void setup function where we initialize the screen and call different test functions to display certain texts or images.  These functions can be edited to display what you want based on your project needs.

testdrawtext("Lorem ipsum dolor sit amet, consectetur adipiscing elit. Curabitur adipiscing ante sed nibh tincidunt feugiat. Maecenas enim massa, fringilla sed malesuada et, malesuada sit amet turpis. Sed porttitor neque ut ante pretium vitae malesuada nunc bibendum. Nullam aliquet ultrices massa eu hendrerit. Ut sed nisi lorem. In vestibulum purus a tortor imperdiet posuere. ", ST7735_WHITE);

All the functions called under the void setup function, perform different functions, some draw lines, some, boxes and text with different font, color and size and they can all be edited to do what your project needs.

The complete code for this is available under the libraries example on the Arduino IDE. Don’t forget to change the DC and the RESET pin configuration in the code to match the schematics.

Uploading the code to the Arduino board brings a flash of different shapes and text with different colors on the display. I captured one and its shown in the image below.

That’s it for this tutorial guys, what interesting thing are you going to build with this display? Let’s get the conversation started. Feel free to reach me via the comment section if you have any questions as regards this project.

In this tutorial, I’ll explain how to set up an LCD on an Arduino and show you all the different ways you can program it. I’ll show you how to print text, scroll text, make custom characters, blink text, and position text. They’re great for any project that outputs data, and they can make your project a lot more interesting and interactive.

The display I’m using is a 16×2 LCD display that I bought for about $5. You may be wondering why it’s called a 16×2 LCD. The part 16×2 means that the LCD has 2 lines, and can display 16 characters per line. Therefore, a 16×2 LCD screen can display up to 32 characters at once. It is possible to display more than 32 characters with scrolling though.

The code in this article is written for LCD’s that use the standard Hitachi HD44780 driver. If your LCD has 16 pins, then it probably has the Hitachi HD44780 driver. These displays can be wired in either 4 bit mode or 8 bit mode. Wiring the LCD in 4 bit mode is usually preferred since it uses four less wires than 8 bit mode. In practice, there isn’t a noticeable difference in performance between the two modes. In this tutorial, I’ll connect the LCD in 4 bit mode.

BONUS: I made a quick start guide for this tutorial that you can download and go back to later if you can’t set this up right now. It covers all of the steps, diagrams, and code you need to get started.

Here’s a diagram of the pins on the LCD I’m using. The connections from each pin to the Arduino will be the same, but your pins might be arranged differently on the LCD. Be sure to check the datasheet or look for labels on your particular LCD:

Also, you might need to solder a 16 pin header to your LCD before connecting it to a breadboard. Follow the diagram below to wire the LCD to your Arduino:

The resistor in the diagram above sets the backlight brightness. A typical value is 220 Ohms, but other values will work too. Smaller resistors will make the backlight brighter.

All of the code below uses the LiquidCrystal library that comes pre-installed with the Arduino IDE. A library is a set of functions that can be easily added to a program in an abbreviated format.

In order to use a library, it needs be included in the program. Line 1 in the code below does this with the command #include . When you include a library in a program, all of the code in the library gets uploaded to the Arduino along with the code for your program.

Now we’re ready to get into the programming! I’ll go over more interesting things you can do in a moment, but for now lets just run a simple test program. This program will print “hello, world!” to the screen. Enter this code into the Arduino IDE and upload it to the board:

There are 19 different functions in the LiquidCrystal library available for us to use. These functions do things like change the position of the text, move text across the screen, or make the display turn on or off. What follows is a short description of each function, and how to use it in a program.

TheLiquidCrystal() function sets the pins the Arduino uses to connect to the LCD. You can use any of the Arduino’s digital pins to control the LCD. Just put the Arduino pin numbers inside the parentheses in this order:

This function sets the dimensions of the LCD. It needs to be placed before any other LiquidCrystal function in the void setup() section of the program. The number of rows and columns are specified as lcd.begin(columns, rows). For a 16×2 LCD, you would use lcd.begin(16, 2), and for a 20×4 LCD you would use lcd.begin(20, 4).

This function clears any text or data already displayed on the LCD. If you use lcd.clear() with lcd.print() and the delay() function in the void loop() section, you can make a simple blinking text program:

The cursor position is defined with lcd.setCursor(column, row). The column and row coordinates start from zero (0-15 and 0-1 respectively). For example, using lcd.setCursor(2, 1) in the void setup() section of the “hello, world!” program above prints “hello, world!” to the lower line and shifts it to the right two spaces:

You can use this function to write different types of data to the LCD, for example the reading from a temperature sensor, or the coordinates from a GPS module. You can also use it to print custom characters that you create yourself (more on this below). Use lcd.write() in the void setup() or void loop() section of your program.

The function lcd.noCursor() turns the cursor off. lcd.cursor() and lcd.noCursor() can be used together in the void loop() section to make a blinking cursor similar to what you see in many text input fields:

This function turns on any text or cursors that have been printed to the LCD screen. The function lcd.noDisplay() turns off any text or cursors printed to the LCD, without clearing it from the LCD’s memory.

These two functions can be used together in the void loop() section to create a blinking text effect. This code will make the “hello, world!” text blink on and off:

This function takes anything printed to the LCD and moves it to the left. It should be used in the void loop() section with a delay command following it. The function will move the text 40 spaces to the left before it loops back to the first character. This code moves the “hello, world!” text to the left, at a rate of one second per character:

This function takes a string of text and scrolls it from right to left in increments of the character count of the string. For example, if you have a string of text that is 3 characters long, it will shift the text 3 spaces to the left with each step:

Like the lcd.scrollDisplay() functions, the text can be up to 40 characters in length before repeating. At first glance, this function seems less useful than the lcd.scrollDisplay() functions, but it can be very useful for creating animations with custom characters.

lcd.noAutoscroll() turns the lcd.autoscroll() function off. Use this function before or after lcd.autoscroll() in the void loop() section to create sequences of scrolling text or animations.

This function sets the direction that text is printed to the screen. The default mode is from left to right using the command lcd.leftToRight(), but you may find some cases where it’s useful to output text in the reverse direction:

This command allows you to create your own custom characters. Each character of a 16×2 LCD has a 5 pixel width and an 8 pixel height. Up to 8 different custom characters can be defined in a single program. To design your own characters, you’ll need to make a binary matrix of your custom character from an LCD character generator or map it yourself. This code creates a degree symbol (°):

If you found this article useful, subscribe via email to get notified when we publish of new posts! And as always, if you are having trouble with anything, just leave a comment and I’ll try to help you out.

When the system is pluged in to power, it will connect to the WiFi (the connection informations --- ssid and password ---, must be configured in code ), will display an inspirational quote for one hour and go to sleep for 24 hours. After the long sleep, it will connect again to the WiFi, display another quote and go to sleep. Again and again.

But there is a plot twist. The used microcontroller (ESP8266) can go to sleep for only 3 hours and 25 minutes (according to the Internet --- see IV.Credits --- ). So I decided to wake up the microcontroller after the before mentioned time (3 hours and 25 minutes) and then put it back to sleep. This will be done 7 times (a total of 23 hours). To keep track of the numbers of wake-ups between 2 quotes, I saved a counter in the RTC user memory from the ESP8266 ( --- see IV.Credits --- ). In this way, when the microcontroller goes to sleep the counter will be kept.

This seems to be all, but... IT IS NOT! The RTC from ESP8266, when this microcontroller is in DeepSleepMode, is not very precise ( in my tests it will fall behind with at least 1 hour in 23 hours of DeepSleep ). So to fix this issue, I made the ESP8266 to take the time from an NTP Server, after displaying the quote for an hour, and storing the hours and minutes in the RTC memory. When the 7 cycles of waking-up and going back to sleep, the ESP8266 take again the time from the NTP Server and compare the stored time with the one took seconds ago. If the hour stored is later than the current hour, the ESP8266 will go to DeepSleep for the remaining time between the two intervals of time ( the stored one and the current one ).Else, if the number of minutes stored are greater than the number of current minutes, the ESP8266 will go to LightSleep for the remaining number of minutes between the two intervals of time ( this time, the RTC is precise enough to wake up the ESP8266 at the exact time ).

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (8" diagonal) bright (36 white-LED backlight) and colorfu 800x480 pixels with individual pixel control. As a bonus, this display has a optional capacitive touch panel with controller GT911 and resistive touch panel with controller XPT2046 attached by default.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (Due/Mega 2560). This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

For 8 inch screen,the high current is needed.But the current of arduino uno or arduino mega board is low, an external 5V power supply is needed. Refer to the image shows the external power supply position on shield ER-AS-SSD1963.

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

This module is designed to plug directly into Arduino UNO R3 (or its clone) boards. It is compatible with CH340 and Atmega16u2 version boards, as well as Mega 2560. This LCD shield may also work with other boards, but the compatibility can"t be guaranteed.

Granted, the Arduino doesn’t have much use for text when used on it’s own. It has no display. But a display can be attached, or text can be send/received through the serial port and other ways of communication.

We have used strings already a few times. Each time when we used a “Serial.print() ” or “Serial.println() “, we actually already used strings. Remember that a text in C needs to be enclosed in double quotes? That would make it a string.

Please consider disabling your ad blocker for our website.We rely on these ads to be able to run our website.You can of course support us in other ways (see Support Uson the left).

In the case of a string, the array keeps going, until your Arduino finds a NULL character. The NULL character terminates the string – or indicates the end of the string.

It’s character zero. But we do not (yet) have to worry about that – but it is something to keep in mind. Since strings are quite often used, the language “C” which we use for Arduino Programming, comes with a standard library of string related functions, which handle quite a lot already automatically.

What this does, is create an array of characters (which is a string), the empty square brackets basically says “compiler! Go figure out yourself how large this array should be“. If we would have entered a number, then that number should at least be big enough to hold our string plus one NULL character.

Note that if the number is bigger than the number of characters we need, then this will work just fine. However, your Arduino might allocate the extra characters as well and waste memory space as we’re not using it. On the other hand, if you expect the string to change in the program and all those characters might be needed, then you’d already be prepared.

The variable “Name” points to the memory location of the “H” character of the string, which is at position 0 (zero) and therefor has “0” as it’s index number.

Not really. Remember how I said before that the variable (in our example “Name”) actually points to the memory location of the first element in the array? It’s a memory address, which is not the same as a string. Believe me, this is something you’ll run into quite often, and it’s one of the reason why I’m not a fan of the C-language (I’m more of a Pascal fan – and plenty of people will argue with me on that one).

Unfortunately this makes things more complicated, and we’d have to assign each character to the proper element. Thank goodness there is a function for that: strcpy() .

Please consider disabling your ad blocker for our website.We rely on these ads to be able to run our website.You can of course support us in other ways (see Support Uson the left).

Now sometimes we’d like to print for example double quotes, but just typing them into a string will not work – the string would break. The compiler will think you’re done after seeing the second double quotes and everyting remaining will become an unclear mess.

The code highlighting of the Arduino IDE text editor, will show you if a string “breaks” or not, by changing character colors in the string you just typed.

Note that when you want the next character to be special as well, then you’d need to “escape” those as well. For example if we add multiple double quotes around the word “guest”: Serial.println("Hello \"\"guest\"\", welcome to Arduino");

This trick has to be used for certain other characters as well, for example starting a new line is an ASCII character (see the character table, and look in the “Esc” column). If we’d like to place a line break (start a new line) in our string, then we would need ASCII character 10, which we write as “\n”.

The error message  invalid conversion from "const char*" to "char"  tells us that we are assigning the wrong kind of datatype to our array element. In simple words: This is because we are trying to assign a string to a character.

However, if our string becomes shorter, for example by replacing “Hans” with “Max” (my other nephew), then we would need to add the NULL character again:

Obviously, using ASCII is not the obvious way to do it when you’d like to assign text to a string. However, there are scenario’s where this can be very practical. I’ll illustrate this with a quick nonesense example, which quickly lists all the letters of the alphabet, where we can use a “for” loop to count from 65 (=A) to 90 (=Z).

Please consider disabling your ad blocker for our website.We rely on these ads to be able to run our website.You can of course support us in other ways (see Support Uson the left).

When we added ” has two nephews, called Bram and Max!” to that string/array, we royally exceed the pre-defined space, and your Arduino will try to print that anyway. Not being able to find the NULL character (we have overwritten it with a non-NULL character, a space-character, in this example), it will keep spitting out whatever is in memory until it finds a NULL character. Which might be right away, or never …

The tedious and cumbersome things we had to do with the old “string” (lowercase: Array of Char), are done much easier with the “String” (Capital “S”: an object) object … but what is an object?

For one; everything is logically grouped together. There is no confusion to what item the properties or functions belong. So when we aks for properties or call a method (function) of a given object “car” then we know it only relates that that specific car.

Another reason is that once an object has been defined, it actually kind-a behaves like a data type, which can use for variables. Say we have one “car” then we create a variable “MyCar” as the object (data type) “car”. But if we have a garage filled with cars, then we can re-use that same definition to create multiple variables (MyCar, YourCar, DadsCar, MomsCar), or even an array of cars (Cars[0], Cars[1], Cars[2],…).

With “Serial” we have already seen the methods (functions) “begin”, “print” and “println”. We call these methods to have the object do something , like start communication, or send a string to our Serial Monitor of our Arduino IDE.

As mentioned and shown before: the array of char variant of a string is a little cumbersome to work with. So the good people at Arduino created an object to make working with strings easier. Again a reminder: it’s the “String” with a capital “S”!!!

Line 10 could also be written as Name = String("Bram"); , which will actually work as well, but now we assign the new object (holding the string “Bram”) to the old object, versus the method in the code where we assign just a string to the object.

Now let’s make that string longer, in the previous example, when using the array of char “string”, we noticed that we had to pay attention to the size of the array, so we wouldn’t go beyond it’s capacity. The “String” object however saves us that worry. It corrects automatically.

You see? We can assign a much larger string than what we started out with, and when printing it, we experience zero problems. This is already a second point where the object is easier to use.

Please consider disabling your ad blocker for our website.We rely on these ads to be able to run our website.You can of course support us in other ways (see Support Uson the left).

We create the String object “Name” and assign it the value “Hans” (lines 7 and 8), which we can print with “Serial” as we have seen before. Now in line 12, we retrieve the length of our string – which is just the number of characters in the string, and not including the NULL terminating character. This is done with the “length()” method of the “String” object: Name.length() . This method will return a number, an integer, which we send right away to “Serial.print”.

In line 14, we call the method “concat()” to concatenate ” has two nephews, called Bram and Max!” to the original string “Hans”. As you can see, this works right away. But … there is an easier way to glue an extra string to your “String” object by simply using the plus symbol (+), even the compound operator “+=” works. See lines 27 and 28, where we use “+=” and even the regular “+”.

The “String” object however is even more powerful and can right away convert a number (int in this example) to a string, and replace or attach it to an existing string – see line 34 – which is something we cannot do with the previous “string” array of characters.

Now if we know that String("some text") returns a “String” object, and we know that we can glue strings together with the plus symbol (+), and we know that “Serial.println()” take a “String” as a parameter,… then we can do some tricks to save us the hassle of writing 2 “Serial” lines (print() and println()) whenever we want to print values or variables.

The reason why this fails, is because we are comparing a string with the memory location “pointer” of an array. Which will not be the same obviuosly. We actually need to use a special function for this: “strcmp()”  (read that as “string compare”)

When comparing the two strings, it will actually compare the ASCII values. So when it returns a number greater than zero, it actually means that it ran into a character which has a greater ASCII value compared to the other character, in the same position in the other string, and this can be confusing, because we humans would expect “Hans” to be greater than “Hi” – but its not. This is in part also because we humans see the longer string “Hans” as the larger one of the two.

Comparing “String” objects result in the same kind of confusion, but instead of using the “strcmp()” function, we can use the simple comparison operators.

If you have questions, just ask them below in the comment section, and keep in mind: There are no stupid questions! We all had to start at some point!

Most displays are designed to be "on top" of a stack of shields, so they don"t use stacking connectors, but that doesn"t mean that they are actually using all of the pins. You have to connect your other signals to some shield "underneath" the display, and no longer have the luxury of just sticking wires into the connectors. I mean, it"s a DISPLAY and it"s supposed to look nice! For example, the Adafruit TFT display specifically says:

QuoteThe display uses digital pins 13-9. Touchscreen controller requires digital pin 8. microSD pin requires digital #4. That means you can use digital pins 2, 3, 5, 6, 7 and analog 0-5. Pin 4 is available if not using the microSD