sainsmart 3.2 tft lcd display pinout made in china

SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

There is built-in SD card slot in the shield, so we can use it to upload images. But the images need to be converted RAW format first.You can use the tool here. SD libraries need to be preinstalled for displaying the image.

SainSmart 3.2" TFT LCD Displayis a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

The 3.2 inch TFT LCD module is a special design for Raspberry Pi for portable application. It features a 3.2” display with 320x240 16bit color pixels and resistive touch screen. The LCD is well mated with Pi board and interface with Pi via the high speed SPI port, and support console, X windows, displaying images or video etc. It also provides 4 press buttons for user defined functions.

RPi LCD needs to use a SPI interface, but in the original image file of Raspberry Pi, the displayer is driven via a HDMI port. So the original image is not applicable for RPi LCD, and you should install the LCD driver to your Pi or use the Ready-to-use image file provided by Sainsmart,click here.

Download the LCD driver and extract it to your Raspbian OS (e.g. copy the driver to your Pi by sftpor using U disk). Then run the following command via putty:

This LCD can be calibrated using a program called xinput_calibrator which is pre-installed on the offer image. However, it was not pre-installed on original Raspbian OS. So in this case, you should get and install the program manually with

After running these commands, there will be a prompt for four-point calibration shown in the LCD screen. Click the points one by one to finish the touch calibration. Then, the new calibration data will be displayed in the terminal, as shows below. Please get these data for future use.

※ Price Increase NotificationThe TFT glass cell makers such as Tianma,Hanstar,BOE,Innolux has reduced or stopped the production of small and medium-sized tft glass cell from August-2020 due to the low profit and focus on the size of LCD TV,Tablet PC and Smart Phone .It results the glass cell price in the market is extremely high,and the same situation happens in IC industry.We deeply regret that rapidly rising costs for glass cell and controller IC necessitate our raising the price of tft display.We have made every attempt to avoid the increase, we could accept no profit from the beginning,but the price is going up frequently ,we"re now losing a lot of money. We have no choice if we want to survive. There is no certain answer for when the price would go back to the normal.We guess it will take at least 6 months until these glass cell and semiconductor manufacturing companies recover the production schedule. (Mar-03-2021)

ER-TFT032-2 is 240x320 dots 3.2 " color tft lcd module display with ILI9320 controller and optional 4-wire resistive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 16-bit parallel interface. .FPC is soldering type,there is no need for zif connector.Lanscape mode is also available.

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

The RPi LCD can be driven in two ways: Method 1. install driver to your Raspbian OS. Method 2. use the Ready-to-use image file of which LCD driver was pre-installed.

3) Connect the TF card to the Raspberry Pi, start the Raspberry Pi. The LCD will display after booting up, and then log in to the Raspberry Pi terminal,(You may need to connect a keyboard and HDMI LCD to Pi for driver installing, or log in remotely with SSH)

1. Executing apt-get upgrade will cause the LCD to fail to work properly. In this case, you need to edit the config.txt file in the SD card and delete this sentence: dtoverlay=ads7846.

This LCD can be calibrated through the xinput-calibrator program. Note: The Raspberry Pi must be connected to the network, or else the program won"t be successfully installed.

Arduino mega + 3.2" tft case. there are 2 different case bottoms, 1 without a hole and 1 with. both cases have a cutout for powering the Mega from a USB.

I designed this to dress up a project that used the SainSmart LCD Keypad Shield with and Arduino. The bezel itself prints pretty easily with very little support structure needed. The buttons are designed to be self-captivating (they just push in and...

I didn"t have a 3.5" TFT screen, but I did have the 3.2" ones (at the time the 3.5" were on backorder and I got impatient). This fits my 3.2" TFT perfectly. ... My unit comes from 4D Systems as well.

This top surface has 4 additional holes (for screwing to the bezel) and a square cut out of it to fit the LCD circuit board (see attached photo above) The bezel has 4 screw holes that line up with laser cut holes in the laser cut back plate. the...

Support piece for SainSmart kit: http://www.sainsmart.com/sainsmart-mega2560-board-3-5-tft-lcd-module-display-shield-kit-for-atmel-atmega-avr-16au-atmega8u2.html When both the shields are stacked, they are kind of flappy. This part fits on one end...

accurate CAD model of UPC "6013801500024" from the SainSmart Raspberry Pi 3 Model B Ultimate Kit with 5 inch LCD (Red&White Case)https://smile.amazon.com/gp/product/B01FHEBIE0/

A (very) compatible 800x480 LCD is available, but it"s 5 inch big and so the original bezel won"t fit. I also didn"t like the idea of sticking LCD to PCB by a piece of double sided tape. Here"s my original post about hacking it in:(pocket)CHIP with...

The cable canal lid I used had a thickness of 1.5mm. How to assemble it: Bezel -> Cable canal lid -> Display Cut a rectangle for the whole display without the PCB inside...

I bought a 4.3" TFT LCD Color Monitor off eBay for a reverse camera I installed in my car and had nothing to mount it to my car with. Monitor dimensions were 120mm(L) x 75mm(W) x 15mm(H) and this seemed to fit quite snugly. I have only created a...

This is a sipmple box/case for Arduino Uno and 2.4"" TFT Lcd Touch Screen. There are 2 kind of cases: closed or with open grooves for refrigeration. Originally made for a mini - meteo station, it can be customizable with FreeCad file. ...It was made...

A small mountable holder for a fasttech LCD module. Mounting pins are a little tight but can be snapped off if not needed. Mount holes are designed for assorted leg or spacer designs. Holes are 5mm dia, 34mm apart and hole centre 5.5mm from edge if...

I just redesigned it so it can house cheap chinese 2.4" TFT touchscreen, instead of hard to find and expensive 2.8". No support is needed for any of parts.

This is an update to the FreeTouchDeck case by Dustin Watts that holds a 3.2" TFT display since I bought a different size than Dustin used. I modified the Top_for_TFT_with_Headers.stl file. I"ve also uploaded the Fusion 360 file....

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

Step 1: Remove dial knob by grabbing the whole knob and pulling towards yourself Step 2: Remove 2ea 3mm front mount screws Step 3: Remove 4ea 2mm from the backside of the LCD screen that mount the circuit board to the frame bracket Step 4: Snap your...

LCD screen bezel for Oneplus 2. If not only your screen is destroyed, but also the black plastic frame surrounding it (see picture), you can try your luck by printing this bezel and installing it. Replacement screens do not come with this bezel,...

At this stage, any panel would need to connect either to the HDMI or VGA port. Although there is a dedicated TFT connector on the board it"s not currently available for use. Foundation hopes to sell/promote a tested TFT once all tht other stuff is done!

If you just want to use a display without all of the challenge of getting a display to work from the various pins, you might want to search around for small displays that take either composite or HDMI inputs. Adafruit.com has several displays that take composite. I have a MP4 player from JXD that is fairly small and does video input that I"ve been meaning to use when I get to the r-pi.

Yes it"s ST7735 based like the Adafruit ones. I"ve got one with an Sainsmart Arduino UNO from China, comes with the ST7735 code for the Arduino by LadyAda.

I have started a project writing framebuffer drivers for small TFT LCDs. I have written a helper module that greatly simplifies writing such a driver. That is if the display is RGB565 and uses SPI. I have ordered two more modules that I will try and make drivers for:

notro wrote:I have started a project writing framebuffer drivers for small TFT LCDs. I have written a helper module that greatly simplifies writing such a driver. That is if the display is RGB565 and uses SPI. I have ordered two more modules that I will try and make drivers for:

Reason: The hooks on the backight of ER-TFT032-3.1 is always complained by most customers for inconvenient assembly. So we cancel the hooks in the new version of ER-TFT032-3.2.That"s the only difference for these two versions.

ER-TFT032-3.2 is 240x320 dots 3.2" color tft lcd module display with ILI9341 controller and optional 4-wire resistive touch panel and 3.2 inch capactive touch panel with controller FT6236,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8/16-bit parallel,3/4-wire serial interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.2"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

SainSmart 3.2" TFT LCD Display + TFT LCD Shield For Arduino Mega2560 R3. Overview: SainSmart 3.2" TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and multifunctional module for your project. The Screen include a controller SSD1289, it"s a support 8/16bit data interface , easy to drive by many MCU like STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is ADS7843 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller. Specification: 240374PQ 65K color 320*240 3.2 inch Wide viewing angle SSD1289:240 RGB x 320 TFT Driver Integrated Power, Gate and Source Driver With RAM ADS7843:4-WIRE TOUCH, UP TO 125kHz CONVERSION RATE, SERIAL INTERFACE SainSmart 3.2 TFT LCD shield works in 3.3V voltage level and you need to use cables to connect with Arduino Mega. And this shield can help you out of the bothers to use other cables. You just need to plug the module to Mega through this shield.This shield supports both 16 bit mode. And Mega board has enough pins for using SD card and touch function at the same time.It also has an adjustable button for contrast of the LCD display. Packing List: 1 X SainSmart 3.2 inch TFT LCD 1 X Shield Board for Arduino Mega2560 R3 Item will be shipped within 1-2 working days after full payment is cleared. Tracking number will be sent to all customers upon package shipment. Delivery time is different in accordance to shipping address and shipping methods. -Economy shipping from China: about 20-30 business days. -ePacket delivery (EUB) from China to US: about 10-15 business days. -Expedited shipping from China takes about 3-5 business days via DHL/UPS and 9-15 business days via EMS. -Standard shipping (Royal Mail Tracked) from UK warehouse to local customers: about 3-5 business days. -Standard shipping from US warehouse: about 3-7 business days. -Expedited shipping from US warehouse: about 3-5 business days. Delivery time depends on destination logistics mode and other factors. If you have not received your shipment within 30 days from payment, please feel free to contact us. We will track the shipment and get back to you as soon as possible with a reply. We accept payment via PAYPAL ONLY . We only ship to confirmed PAYPAL addresses. Please make sure payment address in PayPal is correct. All major credit cards are accepted through our secure payment processor PayPal. Payment must be received within 7 business days of auction closing. 60 days money back return policy . If you are not satisfied when you receive your item, please return it within 60 days for a replacement or money back. Please contact us for return address before you send it back. If item defective, In 3 months we will send you a replacement without extra charge, or offer refund upon faulty received. After 3 months you are still welcomed to send it back to us for exchange. Buyer may responsible for all return shipping costs. In case you receive wrong products due to shipping error, please contact us for exchange or refund. If it"s damaged, please refuse to accept and contact us as soon as possible. Please email us before leaving any negative feedback or open any dispute on PayPal. We care about our valued customers, and will always try to help you. So if you have any problems, please e-mail us immediately. We try our best to reply to your emails as soon as possible. If you do not receive any reply from us, please check your email ensuring your mailbox has not reached full size. You can contact us by Ebay messages are strongly recommended. On Oct-25-17 at 03:43:18 PDT, seller added the following information: