lcd panel tn vs va quotation

Again, IPS is the clear winner here. The vertical viewing angles are very similar to the horizontal ones on both IPS and VA panels. Unfortunately, this is one area where TN panels are usually much, much worse. TN monitors degrade rapidly from below, and colors actually inverse - resulting in a negative image that can be distracting. For this reason, if you decide to buy a TN monitor, look for one with an excellent height adjustment, or consider buying a VESA mounting arm, as you should mount TN monitors at eye level. Even when mounted properly, larger TN displays can appear non-uniform at the edges.

There"s usually not much difference between VA and IPS panels in terms of gray uniformity. It"s rare for monitors to have uniformity issues, and even on monitors that perform worse than average, it"s usually not noticeable with regular content. TN monitors tend to perform a bit worse than usual, though, and the top half of the screen is almost always darker than the rest, but that"s an artifact of the bad vertical viewing angles.

Black uniformity tends to vary significantly, even between individual units of the same model, and there"s no single panel type that performs the best. It"s rare for monitors to have good black uniformity, and almost every monitor we"ve tested has some noticeable cloudiness or backlight bleed. IPS and TN panels can look slightly worse due to their low contrast ratios, as the screen can take on more of a bluish tint when displaying dark scenes. Like with contrast, black uniformity issues usually aren"t very noticeable unless you"re looking at dark content and you"re in a dark room. If you only use your monitor in a bright environment, generally speaking, you don"t need to worry about black uniformity.

Historically, TN panels used to have the worst colors, as many of them were cheaper models that only supported 6-bit colors or used techniques like dithering (FRC) to approximate 8-bit colors. Most displays today, including TN models, are at least 8 bit, and many of them are even able to approximate 10-bit colors through dithering. New technologies, like LG"s Nano IPS and Samsung"s Quantum Dot, add an extra layer to the LCD stack and have significantly improved the color gamut of modern IPS and VA displays, leaving TN a bit behind. Between them, NANO IPS is slightly better, as it tends to offer better coverage of the Adobe RGB color space. Although the difference is minor, IPS panels still have a slight edge over VA and TN displays.

Although TN panels have caught up a bit in the SDR color space, they"re far behind when it comes to HDR, so if you"re looking for a good HDR color gamut, avoid TN panels. Between VA and IPS panels, the difference isn"t as significant; however, IPS panels still have a slight edge. The best VA panels top out at around 90% coverage of the DCI P3 color space used by most current HDR content. IPS panels go as high as 98% coverage of DCI P3, rivaling even some of the best TVs on the market. Due to the very high coverage of DCI P3 on both VA and IPS, the difference isn"t that noticeable, though, as most content won"t use the entire color space anyway.

Although not necessarily as noticeable to everyone as the differences in picture quality, there can also be a difference in motion handling between IPS, VA, and TN displays. TN panels historically offered the best gaming performance, as they had the highest refresh rates and extremely fast response times. Manufacturers have found ways to drastically improve the motion handling of VA and IPS panels, though, and the difference isn"t as pronounced.

LCD panel technology has changed drastically over the last few years, and the historical expectations for response time performance don"t necessarily hold anymore. For years, TN monitors had the fastest response times by far, but that"s started to change. New high refresh-rate IPS monitors can be just as fast.

VA panels are a bit of a strange situation. They typically have slightly slower response times overall compared to similar TN or IPS models. It"s especially noticeable in near-black scenes, where they tend to be significantly slower, resulting in dark trails behind fast-moving objects in dark scenes, commonly known as black smear. Some recent VA panels, such as the Samsung Odyssey G7 LC32G75T, get around it by overdriving the pixels. It results in much better dark scene performance but a more noticeable overshoot in brighter areas.

Within each of the three types of LCD we mentioned, other related panel types use the same basic idea but with slight differences. For example, two popular variants of IPS panels include ADS (technically known as ADSDS, or Advanced Super Dimension Switch) and PLS (Plane to Line Switching). It can be hard to tell these panels apart simply based on the subpixel structure, so we"ll usually group them all as IPS, and in the text, we"ll usually refer to them as IPS-like or IPS family. There are slight differences in colors, viewing angles, and contrast, but generally speaking, they"re all very similar.

There"s another display technology that"s growing in popularity: OLED. OLED, or organic light-emitting diode, is very different from the conventional LCD technology we"ve explored above. OLED panels are electro-emissive, which means each pixel emits its own light when it receives an electric signal, eliminating the need for a backlight. Since OLED panels can turn off individual pixels, they have deep, inky blacks with no blooming around bright objects. They also have excellent wide viewing angles, a near-instantaneous response time, and excellent gray uniformity.

OLED panels aren"t perfect, though. There"s a risk of permanent burn-in, especially when there are lots of static elements on screen, like the UI elements of a PC. There aren"t many OLED monitors available, either, but they"ve started to gain popularity as laptop screens and for high-end monitors, but they"re very expensive and hard to find. They"re also not very bright in some cases, especially when large bright areas are visible on screen. The technology is still maturing, and advances in OLED technology, like Samsung"s highly-anticipated QD-OLED technology, are promising.

As you can probably tell by now, no one panel type works best for everyone; it all depends on your exact usage. Although there used to be some significant differences between panel types, as technology has improved, these differences aren"t as noticeable. The two exceptions to this are viewing angles and contrast. If you"re in a dark room, a VA panel that can display deep blacks is probably the best choice. If you"re not in a dark room, you should focus on the other features of the monitor and choose based on the features that appeal to your exact usage. IPS panels are generally preferred for office use, and TN typically offers the best gaming experience, but recent advancements in VA and IPS technology are starting to change those generalizations. For the most part, the differences between each panel type are so minor now that it doesn"t need to be directly factored into your buying decision.

Your gaming monitor is one of the most important parts of your PC, and a big part of that is down to the type of panel it uses to display all those lovely polygons. You"ve probably seen lots of different monitor panel types crop up in a gaming screen"s specs sheet, too: words like TN, IPS and VA. But what do they actually mean, and how do they affect the quality of your gaming monitor? Well, as you"ve probably guessed from the title up top there, I"m going to tell you everything you need to know about all the different gaming monitor panel types, including their strengths, weaknesses and which one you should look to buy if you want the best possible image quality.

Now, I"m going to warn you - most of what you"ll read below is all going to be pretty general. Not all panel types behave the same way, for example, and there will always be some that outperform the rest. That"s why it"s still important to read proper reviews of gaming monitors so you can get an accurate picture of how a monitor"s panel type stacks up against the rest.

I"m also not going to spend ages talking about the exact chemical structure of every single type of sub-pixel, because, well, there are plenty of other people who have done that already. If you"re after that kind of detail, I"d suggest heading over to the folks at TFT Central. Instead, I"m going to be concentrating on what you actually need to know about gaming monitor panel types, such as how their various characteristics affect their performance, and how you can avoid falling into monitor misery by making sure you know exactly what specs sheets are talking about when they start throwing a million acronyms at you. So let"s get to it.

Let"s start with one of the most common monitor panel types available today: TN, or Twisted Nematic. TN panels are what you"ll find in most gaming monitors these days, especially ones with high refresh rates and those geared toward competitive esports and the like.

The good: That"s because they"re a) generally quite cheap to make and b) have the fastest response times out of all the different panel types. This means there"s less lag between you clicking your mouse or tapping your keyboard and that action being translated onscreen, making them ideal for twitchy shooters and games that need fast reaction times.

The bad: Alas, the disadvantage of picking a TN panel is that they generally don"t have the best colour accuracy and they also have quite narrow viewing angles. The former isn"t the case for every TN screen - those certified by Nvidia for use in their G-Sync gaming monitors, for instance, have to meet rigorous colour accuracy standards - but I"ve seen plenty of non-G-Sync screens that barely cover 85% of the standard sRGB colour gamut, which means washed out colours and generally not very rich and vibrant images.

Viewing angles, on the other hand, are a bit more of a hurdle. Most of the time you"ll see them quoted as 160 / 170 degrees, but unless you"re looking at the screen just right, colours can sometimes look a bit off, while contrast goes up the spout. As a result, getting a TN monitor with a height-adjustable stand as opposed to a fixed one can often be a good way to counteract this problem, as this gives you more flexibility to get the monitor in exactly the right position.

IPS monitors, on the other hand, are all about colour accuracy. Largely made by LG, there have actually been lots of different types of IPS panel that have emerged over the years as varying manufacturers tried their hand at matching the quality of LG"s panels, leading to dozens of different variations and combinations of acronyms. These days, though, most manufacturers (especially gaming ones) just tend to say they"re IPS as opposed a specific variant.

Unless, that is, it"s an AHVA, or Advanced Hyper-Viewing Angle, panel. Despite sounding like a VA panel (our third main panel type, which you"ll find more on below), AHVA is actually another type of IPS panel produced by AU Optronics and offers pretty much identical performance to a classic LG IPS panel.

The good: As I just mentioned, IPS panels generally have pretty great colour accuracy (I normally expect an sRGB coverage score of around 96% here) and wide viewing angles, making them better suited to colour intensive work and tasks like photo and video editing. This is true across all types of IPS panel, and their superior viewing angles (often quoted as 178 / 178 degrees) means you don"t get that nasty colour or contrast shift when you"re looking at the screen from a funny angle.

The bad: Unfortunately, their response times are often slower than TN panels, although these have become a lot better in recent years. Personally, I"ve never had any problems with latency when playing games on this type of screen, and for me, image quality is a lot more important than a couple of millisecond"s difference in overall response time.

They can also be more expensive to produce than TN panels, which, combined with their slower response times, is another reason why you don"t tend to see them a lot in displays designed primarily for gaming.

Finally, there"s the VA, or Vertical Alignment panel. Much like IPS, there are dozens of different types of VA panel, but the main ones we need to concern ourselves with are MVA (multi-domain vertical alignment) and AMVA (advanced MVA).

MVA panels were first designed to sit in the middle of TN and IPS displays, offering better viewing angles than TN screens and higher contrast ratios and deeper blacks than IPS. However, their colour accuracy isn"t quite as good as IPS, and they don"t have very fast response times, either.

AMVA, on the other hand (not to be confused with the IPS-like AHVA panel tech described above) builds on that even further, improving the panel"s colour accuracy while still maintaining those ultra high contrast ratios and deep blacks. Its viewing angles still aren"t quite as wide as IPS displays, though, and its response times are still a bit slower as well. However, through the use of features like a monitor"s Overdrive function, VA response times are now much faster than they used to be, making them a much more common occurrence in gaming screens, especially when it comes to curved or ultrawide displays.

The good: As a result, VA monitors can sort of be viewed as the ultimate compromise screen. The key advantages are their best in class black levels and their superior contrast ratios, and compared to TN panels, they also have better viewing angles and higher colour accuracy.

The bad: However, while VA might rectify some of the weaknesses you"ll find in TN screens, they"re still not as colour accurate as IPS panels, and their narrower viewing angles also can"t compete with their IPS rivals, either. Their main weakness, however, is their slow response time, which is generally said to be the slowest of the three main panel types. As I said, steps have been taken to try and mitigate this when it comes to putting a VA panel inside a gaming monitor, but if your gaming library consists solely of competitive shooters and the like, then you"re probably better off looking elsewhere.

In general, IPS, PLS, and VA panels will maintain outstanding image quality and low color degradation no matter where in the room you’re viewing from. A huge boon.

Remember the hype surrounding the final season of Game of Thrones? Now, do you remember the battle with the White Walkers? More specifically, howdark the episode was? If you couldn’t see very well, chances are you weren’t using a VA panel.

VA panels are known to deliver the deepest blacks and richest all-around tones, thanks to their high contrast ratios. This is also why they’re commonly found in television sets. That said, IPS panels come in close behind with contrast ratios of roughly 1000:1.

Due to the comparatively simple nature of TN liquid crystal technology, most TN displays boast low response times between 5ms and 1ms. This allows games to transition from scene-to-scene with very little lag and virtually zero ghosting.

TN panels also feature the highest refresh rates, which is how many times per second a display can re-render a scene (critical for reaching maximum FPS).

High response times and refresh rates are a huge boon for gaming, where split second decisions can make or break a game. As such, TN panels are the optimal choice for PC gamers looking to maximize their competitive advantage.

Given their inexpensive manufacturing costs, TN panels are the most affordable type on our list. In price-ascending order, they’re followed by VA panels, PLS panels, and IPS panels.

Do note, however, that different display models offer different features. High-end TN panels can easily cost more than an entry-level IPS. It depends on the specifications, manufacturer, and various other factors.

Choosing the best panel type ultimately comes down to personal needs and preference. That said, we hope these guidelines help. Your perfect display is out there.

Whether you’re seeking a VA vs IPS vs TN monitor, we’ve assembled this list of the web’s most frequently asked questions to offer an easy solution to all your display inquiries.

So, why would anyone ever buy a TN panel? For starters, they’re cheap. They don’t cost a lot to produce, so they’re often used in the most budget-friendly options. If you don’t value color reproduction or need excellent viewing angles, a TN panel might be fine for your office or study.

TN panels also have the lowest input lag—typically around one millisecond. They can also handle high refresh rates of up to 240 Hz. This makes them an attractive option for competitive multiplayer games—especially eSports, where every split-second counts.

IPS technology was developed to improve upon the limitations of TN panels—most notably, the poor color reproduction and limited viewing angles. As a result, IPS panels are much better than TNs in both of these areas.

In particular, IPS panels have vastly superior viewing angles than TNs. This means you can view IPS panels from extreme angles and still get accurate color reproduction. Unlike TNs, you’ll notice very little shift in color when you view one from a less-than-ideal perspective.

IPS panels are also known for their relatively good black reproduction, which helps eliminate the “washed out” look you get with TN panels. However, IPS panels fall short of the excellent contrast ratios you’ll find on VAs.

While high refresh rates were typically reserved for TNs, more manufacturers are producing IPS panels with refresh rates of 240 Hz. For example, the 27-inch 1080p ASUS VG279QM uses an IPS panel and supports 280 Hz.

Previously, TNs exhibited less input lag than any other panel, but IPS technology has finally caught up. In June 2019, LG announced its new Nano IPS UltraGear monitors with a response time of one millisecond.

Despite the gap being closed, you’ll still pay more for an IPS panel with such a low response time than you would for a TN with similar specs. If you’re on a budget, expect a response time of around four milliseconds for a good IPS monitor.

One last thing to be aware of with IPS panels is a phenomenon called “IPS glow.” It’s when you see the display’s backlight shining through it at more extreme viewing angles. It’s not a huge problem unless you view the panel from the side, but it’s something to keep in mind.

VA panels are something of a compromise between TN and IPS. They offer the best contrast ratios, which is why TV manufacturers use them extensively. While an IPS monitor typically has a contrast ratio of 1000:1, it’s not unusual to see 3000:1 or 6000:1 in a comparable VA panel.

In terms of viewing angles, VAs can’t quite match the performance of IPS panels. Screen brightness, in particular, can vary based on the angle from which you’re viewing, but you won’t get the “IPS glow.”

VAs have slower response times than TNs and the newer Nano IPS panels with their one-millisecond response rates. You can find VA monitors with high refresh rates (240 Hz), but the latency can result in more ghosting and motion blur. For this reason, competitive gamers should avoid VA.

Compared to TNs, VA panels do offer much better color reproduction and typically hit the full sRGB spectrum, even on lower-end models. If you’re willing to spend a bit more, Samsung’s Quantum Dot SVA panels can hit 125 percent sRGB coverage.

For these reasons, VA panels are seen as the jack of all trades. They’re ideal for general use, but they either match or fall short in most other areas except contrast ratio. VAs are good for gamers who enjoy single-player or casual experiences.

When compared to CRT monitors, all LCD panels suffer from some form of latency issue. This was a real problem when TN panels first appeared, and it’s plagued IPS and VA monitors for years. But technology has moved on, and while many of these issues have been improved, they haven’t been eliminated entirely.

Uneven backlighting is another issue you’ll find on all panel types. Often this comes down to overall build quality—cheaper models slack on quality control to save on production costs. So, if you’re looking for a cheap monitor, be prepared for some uneven backlighting. However, you’ll mostly only notice it on solid or very dark backgrounds.

LCD panels are also susceptible to dead or stuck pixels. Different manufacturers and jurisdictions have different policies and consumer laws covering dead pixels. If you’re a perfectionist, check the manufacturer’s dead-pixel policy before you buy. Some will replace a monitor with a single dead pixel for free, while others require a minimum number.

Office or study use: Your budget should be your primary concern here. VA is the do-it-all panel, with superior viewing angles to TN, but either would do the trick. You can save some money because you don’t need high refresh rates or ultra-low latency. They’re still nice, though. You’ll see a noticeable difference in smoothness just when moving the Windows cursor on a monitor with a 144 versus 60 Hz refresh rate.

Photo and video editors/Digital artists: IPS panels are still generally favored for their ability to display a wide gamut of colors. It’s not unusual to find VA panels that also cover a wide gamut (125 percent sRGB, and over 90 percent DCI-P3), but they tend to exhibit more motion blur during fast-paced action than IPS panels. If you’re serious about color accuracy, you’ll need to properly calibrate your monitor.

Programmers who mount monitors vertically: You might think TN panels are great for programmers, but that’s not necessarily the case. TN panels have particularly bad viewing angles on the vertical axis. If you mount your monitor in portrait mode (as many programmers and mobile developers do), you’ll get the worst possible viewing angles from a TN panel. For the best possible viewing angles in this scenario, invest in an IPS display.

Competitive online gamers: There’s no question TN panels are still favored in the eSports world. Even the cheapest models have fast response times and support for high refresh rates. For 1080p gaming, a 24-inch will do just fine, or you could opt for a 1440p, 27-inch model without breaking the bank. You might want to go for an IPS panel as more low-latency models hit the market, but expect to pay more.

Non-competitive, high-end PC gamers: For a rich, immersive image that pops, a VA panel will provide a higher contrast ratio than IPS or TN. For deep blacks and a sharp, contrasting image, VA is the winner. If you’re okay with sacrificing some contrast, you can go the IPS route. However, we’d recommend avoiding TN altogether unless you play competitively.

Best all-rounder: VA is the winner here, but IPS is better in all areas except contrast ratio. If you can sacrifice contrast, an IPS panel will provide fairly low latency, decent blacks, and satisfactory color coverage.

If you can, check out the monitor you’re interested in in-person before you buy it. You can perform some simple ghosting and motion blur tests by grabbing a window with the mouse and moving it rapidly around the screen. You can also test the brightness, watch some videos, and play with the onscreen display to get a feel for it.

By far the most common types of display panels used on PC monitors are TN, IPS and VA. We"re sure you"ve heard these terms before if you"ve researched monitors to purchase, and to be clear, the type of panel is a key piece of information that reveals a lot about how the monitor will behave and perform.

TN is the oldest of the LCD technologies and it stands for twisted nematic. This refers to the twisted nematic effect, which is an effect that allows liquid crystal molecules to be controlled with voltage. While the actual workings of a TN-effect LCD are a little more complicated, essentially the TN-effect is used to change the alignment of liquid crystals when a voltage is applied. When there is no voltage, so the crystal is "off," the liquid crystal molecules are twisted 90 degrees and in combination with polarization layers, allow light to pass through. Then when a voltage is applied, these crystals are essentially untwisted, blocking light.

VA, stands for vertical alignment. As the name suggests, this technology uses vertically aligned liquid crystals which tilt when a voltage is applied to let light pass through. This is the key difference between IPS and VA: with VA, the crystals are perpendicular to the substrates, while with IPS they are parallel. There are several VA variants, including Samsung"s SVA and AU Optronics AMVA.

IPS stands for in-plane switching and, like all LCDs, it too uses voltage to control the alignment of liquid crystals. However unlike with TN, IPS LCDs use a different crystal orientation, one where the crystals are parallel to the glass substrates, hence the term "in plane". Rather than "twisting" the crystals to modify the amount of light let through, IPS crystals are essentially rotated, which has a range of benefits.

There are many IPS variants on the market, with each of the three big LCD manufacturers using a different term to describe their IPS-type technology. LG simply calls their tech "IPS" which is easy for everyone. Samsung uses the term PLS or plane-to-line switching, while AU Optronics uses the term AHVA or advanced hyper viewing angle. AHVA shouldn"t be confused with regular VA displays, it"s an annoying and confusing name in my opinion, but AHVA is an IPS-like technology. Each of LG"s IPS, Samsung"s PLS and AUO"s AHVA are slightly different but the fundamentals are rooted in IPS.

So in summary, TN panels twist, IPS panels use a parallel alignment and rotate, while VA panels use a vertical alignment and tilt. Now let"s get into some of the performance characteristics and explore how each of the technologies differ and in general, which technology is better in any given category.

By far the biggest difference between the three technologies is in viewing angles. TN panels have the weakest viewing angles, with significant shift to color and contrast in both the horizontal and especially vertical directions. Typically viewing angles are rated as 170/160 but realistically you"ll get pretty bad shifts when viewing anywhere except for dead center. Higher-end TNs tend to be somewhat better but overall this is a big weakness for TNs.

VA and IPS panels are both significantly better, with IPS being the best overall for viewing angles. 178/178 viewing angle ratings are a realistic reflection of what you can expect with an IPS, you won"t get much shift in colors or contrast from any angle. VAs are good in this regard but not as good as IPS, mostly due to contrast shifts at off-center angles. With VAs and especially TNs having some color and contrast shifts when viewing at angles, they"re not as well suited to color-critical professional work as IPS panels, which is why you see most pro-grade monitors sticking to IPS.

In terms of brightness there"s no inherent differences between the technologies because the backlight, which determines brightness, is separate to the liquid crystal panel. However there are significant differences to contrast ratios, and this an area most people look at when determining which panel type they want.

Both TN and IPS panels tend to have a contrast ratio around 1000:1, although in my testing I have noted some differences. TN panels tend to have the lowest contrast ratios when calibrated, with an entry-level panel sitting between 700:1 and 900:1 and good panels pushing up to that 1000:1 mark. IPS has a larger range, I"ve seen some as low as 700:1 like TNs, however the very best tend to push up higher than TN, with 1200:1 as the upper range for desktop monitors and some laptop-grade displays reaching as high as 1500:1.

Neither TN nor IPS get to the range of VA though. Entry-level VA panels start with a contrast ratio of 2000:1 from those that we"ve tested, with the best easily exceeding 4500:1, although 3000:1 is a typical figure for most monitors.

TVs make extensive use of VA panels and there contrast ratios can be even higher. It"s not unusual to see over 6000:1. So if you want deep blacks and high contrast ratios, you"ll need to go with something VA.

While IPS panels tend to be a middle ground for contrast they do suffer from a phenomenon called "IPS glow," which is an apparent white glow when viewing dark imagery at an angle. The best panels exhibit minimal glow but it"s still an issue across all displays of this type.

Color quality is another difference many people cite between TN displays and other display panels in particular. And this can be split into two categories: color depth or bit depth, and color gamut.

In both of these regards, TN panels tend to fall on the weaker end of the scale. Many TN displays, in particular entry-level models, are only natively 6-bit and use frame rate control, otherwise called FRC or dithering, to achieve standard 8-bit output. 6-bit panels are prone to color banding, while native 8-bit panels have smoother color gradients and therefore better color output.

Not all TN panels are 6-bit. The top-end TNs are native 8-bit, but it"s safe to say most TNs will only be native 6-bit, even today. If you are after a native 8-bit display, you"ll need to go with either IPS or VA, where many more panels come native 8-bit.

As for native true 10-bit, typically you"ll need to look for an IPS panel, which make up the majority of native 10-bit panels. Some VA panels can do it, but they are rare. Most displays you purchase that claim to be 10-bit, are actually 8-bit+FRC, with only high-end professional-grade monitors offering a native 10-bit experience.

This is another area where VA and IPS provide a superior experience. The best TN panels tend to be limited to sRGB, or in the case of the worst entry-level panels, don"t even cover the entirety of the sRGB gamut. Wide-gamut TN panels do exist, but they are rare.

VA panels typically start with full sRGB coverage as a minimum, and depending on the panel can push higher. VAs that use a quantum dot film, typically from Samsung, offer higher gamuts, around the 125% sRGB or 90% DCI-P3 mark. Most of the wide gamut VA monitors we"ve tested fall between 85 and 90% DCI-P3 coverage, which is a decent result, though the best can approach 95% or higher.

With IPS panels, there is the largest variance. Entry-level IPS displays tend to offer 95% sRGB coverage or less, while the majority stick to full sRGB coverage. Then with high-end displays, usually for professionals, it"s not unusual to see full DCI-P3 and Adobe RGB coverage. Of all the wide gamut IPS displays I"ve tested, the lowest DCI-P3 coverage I"ve seen has been 93%, with over 95% a typical figure. This makes IPS the best technology for wide gamut work.

Throughout most of this discussion we"ve been talking about TN as the worst of the three technologies. So far, it has the worst color reproduction, contrast ratios and viewing angles. But it does have one key advantage, and that comes in the form of speed. TN panels have historically been the best for both refresh rates and response times, however that trend is slowly changing for the better.

Not long ago, we argued that only with a TN panel it was possible to hit 240 Hz, doing so at 1080p and later up to 1440p. Most recently, however we"ve seen IPS monitors hit the highest mark ever for a consumer-grade gaming monitor at 360Hz, and do so very convincingly. We"re sure other monitors will follow but as of writing, the Asus ROG Swift PG259QN can deliver both the fastest response times and an accurate color experience using an IPS panel.

More mainstream monitors using IPS panels tend to range from the regular 60Hz for productivity, up to 165 Hz and 240 Hz depending on the market they"re aimed at. VA panels top out at around 240 Hz at the moment.

Most IPS displays, especially high-grade options for professionals, as well as entry-level office monitors, are either 60 or 75 Hz. Meanwhile, a significantly larger number of VA panels across a wider range of sizes and resolutions are high-refresh, while the big selling point of TN is its super high refresh capabilities.

Another major consideration is response times, which govern the level of ghosting, smearing and overall clarity of a panel. Early IPS and VA panels were very slow, however this has improved a lot with modern panels, so the differences between the three technologies aren"t as pronounced as they once were. TN still holds an advantage here.

Most TN panels have a rated transition time of 1ms, or even lower with some recent releases. Actual grey to grey averages we"ve measured for TN panels tend to be in the 2-3 ms range when overdrive is factored in, which makes TN the fastest technology.

IPS panels are next in terms of speed, though as tends to be the case with IPS, there is a wide variance between the best and worst of this type. High-end IPS monitors, typically those with high refresh rates, can have a transition time as fast as 3ms. Compared to the best TN panels, this still makes IPS slower. However entry-level IPS panels or those without overdrive sit closer to the 10ms range, while mid-tier options tend to occupy the 5 to 7 ms bracket.

VA panels are consistently the slowest of the three types, but again, high-end gaming monitors have been pushing this further on every generation. The absolute fastest VA panel we"ve measured so far has a 4ms response time which is very impressive, though more typical numbers are between 8 and 10 ms for gaming monitors. VA panels also tend to be less consistent with their transitions; some individual transitions can be fast, while others very slow, whereas IPS panels tend to hover more around their overall grey to grey average.

While a lot of people are unlikely to spot the difference between an 8ms VA panel and a 5ms IPS, TN panels overall tend to be noticeably clearer in motion, but that gap is closing with every generation. The slowness of VA panels also limits their real world refresh rate: a 144 Hz panel that only manages a 9ms response time, is actually delivering an image most equivalent to a 110 Hz panel. Whereas most 144 Hz IPS panels can transition faster than the 6.94ms refresh window, leading to a true 144 Hz experience. So that"s something to consider.

As a quick summary, TN panels are the fastest and have the highest refresh rates, however they have the worst viewing angles by far, as well as weak color performance and typically the lowest contrast ratios. TNs are typically used for ultra-fast gaming displays, as well as budget class displays, for both desktop monitors and laptops.

IPS is a middle-ground technology. They typically have the best color performance and viewing angles, mid-tier response times and refresh rates, along with mid-tier black levels and contrast ratios. Due to its top-end color output, IPS panels are the go-to choice for professionals, but you"ll also find them in entry-level displays, office monitors, most laptops and a handful of gaming monitors.

VA panels are the slowest of the three, but have the best contrast ratio and black levels by far. Color performance isn"t quite at the level of IPS, but they still offer a significantly better experience than TN in this regard.

With response times for the best modern VAs approaching the level of a typical IPS, along with broad support for high refresh rates, VA monitors are commonly used for gaming monitors. Entry-level VAs also tend to be superior to entry-level TN and IPS panels, though you won"t find VA used in laptops.

There"s no right answer to which monitor technology is best, because all have their strengths and weaknesses which is why all three coexist on the market today. However if you want our recommendation, we tend to gravitate towards VA panels for most buyers, especially gamers and those after something entry-level. Creative professionals should be looking exclusively at IPS monitors, while those after something dirt cheap or ultra high refresh for competitive gaming should opt for TN, although superior latest-gen IPS and VA offerings are finally matching or even beating the best of TN in some regards.

Contrary to what you may think, not all LCD TVs are built around the same core panel technology. They can actually have at their hearts one of two really quite different technologies: VA or IPS.

Each, as we’ll see, has its own distinct advantages and disadvantages – so much so that we personally think the type of panel a particular TV uses should be presented right at the top of its specifications list, rather than typically left off altogether. Especially as some brands have been known to actually mix and match VA and IPS panels at different screen sizes within the same TV series.

The VA initialism stands for Vertical Alignment. This name is derived from the way VA panels apply voltage to vertically aligned liquid crystals that have been mounted perpendicularly to the panel’s glass substrate, making them tilt as required to let the necessary amount of light through for each image frame.

The main advantage of VA panels is contrast. Their perpendicular crystal alignment provides greater control over the light passing through each pixel, meaning dark scenes and dark areas look less grey / enjoy better black levels.

The extent to which this strength is exploited can vary greatly between different manufacturers, and depends on any number of secondary factors. The type and position of LED lighting a particular VA screen might be using can have an impact, for instance. There are multiple variations on the VA theme available from different manufacturers, too. As a basic principle, though, black levels and contrast are consistently and often considerably better on LCD TVs that use VA panels.

Because of their ability to control light better, high-end VA panels generally deliver more brightness in real world conditions than IPS ones do. This further enhances their contrast capabilities, and arguably makes them more consistently able to do fuller justice to the wider light range associated with high dynamic range technology.

Being able to deliver dark scenes with relatively little overlying low-contrast greyness additionally means that VA panels tend to achieve more consistent colour vibrancy and toning.

VA panels for use in LCD TVs come from a number of panel manufacturers, including Samsung Display (which makes a so-called SVA variant) and AU Optronics (which makes an AMVA variant). TV brands are able to buy in panels from these and other VA panel manufacturers as they see fit.

Samsung Electronics is the most consistent user of VA panels in its LCD TVs. In fact, until recently pretty much every Samsung TV at every price level used a VA panel. For the past couple of years, though, IPS panels have unexpectedly cropped up in one or two parts of Samsung’s TV range, including 2021’s high-end QN85 series.

Sony predominantly uses VA panels on its most premium TVs, but it also habitually mixes IPS and VA panels across its wider mid-range and entry level LCD ranges. The same goes for most of the other big brands, too, including Panasonic and Philips.

IPS stands for In-Plane Switching. Like VA panels, IPS panels work by manipulating voltage to adjust how liquid crystals are aligned. Unlike VA, though, IPS panels orient their crystals in parallel with (rather than perpendicular too) the glass substrates present in every LCD panel, and rotate their crystals around to let the desired amount of light through rather than tilting them.

By far the biggest and most talked about advantage of IPS technology is its support for wider viewing angles. In fact, one way of identifying IPS panels has traditionally been to look for quoted viewing angles of 178 degrees.

When we talk about wide viewing angle support in relation to LCD TVs, we’re talking about how much of an angle from directly opposite the screen you can go before the picture starts to lose contrast, colour saturation and, sometimes, brightness.

With VA panels the angle you can watch them before the picture starts to deteriorate sharply can be really quite limited – as little as 20 degrees off axis. While we’d say the 178-degree claims for regular IPS panels are rather exaggerated, you can typically sit at a significantly wider angle than you can with VA and still enjoy a watchable picture.

We’ve even seen occasional evidence of the edges of really big (75-inch plus) VA screens suffering from the technology’s viewing angle limitations when viewed straight on, whereas this never happens with IPS technology.

The VA/IPS viewing angle situation is muddied a little by the introduction into a few high-end VA TVs of wide angle technologies based around filters or sub pixel manipulation. These technologies can be associated with other problems, though, such as reduced resolution, and can still struggle to suppress backlight blooming around stand-out bright objects with LCD TVs that use local dimming backlight systems.

Traditionally IPS panels have been associated with – on high-end screens, at least – wider colour gamuts than VA panels can readily manage. They retain this colour gamut better, too, when viewing the screen from an angle. This is why many professional designers, for instance, have tended to prefer IPS technology to VA. There can be some pretty extreme variance in the range of colour supported across different IPS price points, though, and improvements in premium VA solutions – especially the widespread use of Quantum Dot technologies – have largely evened things up, at least at the premium end of the VA market. In fact, with dark scenes, at least, IPS’s issues with black levels and ‘grey wash’ effect can give good VA panels a colour advantage.

There was a time when IPS technology was considered to have an edge over VA when it comes to response time, leading to less motion blur and improved gaming reaction times. These days, though, we’re seeing pretty much identically low input lag measurements (between 9.4 and 10.4ms) from both VA and IPS TVs.

As with VA, there are different variations on the basic IPS theme made by different panel manufacturers. LG Display is by far the biggest manufacturer of IPS LCD panels for TVs, but AU Optronics also makes them, as well as, more surprisingly, Samsung – though some of the non-LG Display IPS products seem to be more focused on PC monitors than TVs.

Given how dominant LG Display is in manufacturing IPS LCD panels, it’s not surprising to find that pretty much every LCD TV LG Electronics makes features an IPS panel at its heart. Other TV brands that use IPS panels on at least a few of their TVs each year include Panasonic, Philips, Sony and Hisense. In fact, the only big brand that has tended to shun IPS is Samsung (perhaps because of arch rival LG Display’s dominance of the IPS market).

As noted earlier, it can be frustratingly difficult to determine whether a TV is using VA or IPS technology. Sometimes it is mentioned in the specifications list on a manufacturer’s website – but more often it is not.

If you’re able to actually get your hands on an LCD TV, try knocking gently on its screen. If it’s an IPS panel it will feel solid and the picture will only be slightly affected – or completely unaffected – by the impact of your knocks. If it’s a VA panel, the picture will distort quite noticeably around points of impact.

It’s tempting to assume that any TVs with obviously low contrast are IPS while any screen with a narrow viewing angle is VA. As well as depending on having a wide experience of lots of panels, though, there’s just too much variation in the high and low-end fringes of each technology for this approach to be reliable.

Arguably your best bet is to check out a TV model you’re interested in on an industry website called Displayspecifications.com(opens in new tab), which includes usually reliable information on the core panel of pretty much every TV released.

You might want to consider IPS TV if your room layout means one or more viewers regularly find themselves having to watch the screen from a wide angle (though don’t forget that a small number of high-end VA TVs feature wide viewing angle technology). IPS’s black level limitations tend to be less obvious in bright rooms too, if that fits with the sort of environment your TV is likely to be used in for the majority of the time.

Our long experience of testing VA and IPS TVs, though, has led us to conclude that in general, the sort of person most likely to be turning to us for buying advice will be happier with an LCD TV based on VA technology.

VA’s ability to deliver typically much deeper, more convincing black levels and more HDR-friendly contrast helps them deliver a much more consistent and immersive modern AV experience. Especially if you’re the sort of person who likes to dim the lights for serious movie or TV viewing nights.

These cookies help to improve the performance of BenQ. If you want to opt-out of advertising cookies, you have to turn-off performance cookies. We also use Google Analytics, SessionCam and Hotjar to track activity and performance on the BenQ website. You can control the information provided to Google, SessionCam and Hotjar.  To opt out of certain ads provided by Google you can use any of the methods set forth here or using the Google Analytics opt out browser add-on here. To opt-out of SessionCam collecting data, you can disable tracking completely by following link：https://www.hotjar.com/privacy/do-not-track/.

These cookies are used to track your activity on the BenQ website and other websites across the Internet, help measure the effectiveness of our advertising campaign and deliver advertisements that are more relevant to you and your interests. We use various advertising partners, including Amazon, Facebook, and Google. These cookies and other technologies capture data like your IP address, when you viewed the page or email, what device you were using and where you were. You can find out how to avoid them below.

Whether to pick a VA (Vertical Alignment) panel or IPS (In-Plane Switching) panel depends on your intent. These two panels have two primary differences. VA offers a high contrast ratio with limited viewing angles, while IPS comes with a lower contrast but wider viewing angles.

Both these panels have their highs and letdowns. The most straightforward way to determine your pick is by deciding which attributes are the most important for you.

If you need a monitor for competitive gaming, office work, programming, etc., it might be a bit challenging to decide. Fortunately, I will take you through what to expect from them, having tested various VA and IPS panels myself.

Key TakeawaysYour purpose will determine whether you choose an IPS (In-Plane Switching) panel or a VA (Vertical Alignment) panel. There are two main distinctions between these two panels

Image quality is a broad topic that encompasses multiple details. I will focus on the colors that IPS and VA panels have, how the two panels contrast light and dark areas, and the viewing angle of the two panels.

I love IPS panels because they have one of the highest color gamut performances, much higher than VA panels. For this reason, IPS panels display a game"s graphics better than VA panels. These screens represent the graphics of your games more realistically and 40 inch 4K monitors are now top of the range.

What I enjoy more when using VA gaming monitors is the intensity of their contrast ratio. I love how defined the difference between dark and light areas is and how this may aid in the quick identification of situations that may jeopardize your winning chances.

VA monitors may not offer you a TN panel"s performance as well. And while I may not like the average refresh rates of IPS monitors, VA panels are a bit more restrictive when it comes to supported games.

While low response times are common in IPS panels, most IPS gaming monitors have about four milliseconds. This level is not much of a problem for most games. However, I"m not too fond of it when playing racing and fast shooter games because of ghosting.

A VA panel is slightly slower than an IPS panel. Therefore, you will notice slightly more motion blur when playing your games. Like IPS panels, some options offer you a one-millisecond response time for image sharpness.

If you need a monitor with an amazing contrast ratio, look into VA panels. And with the provision of VA monitors with a slower response time, you can find screens that offer a good gaming experience in most games.

Different Liquid Crystal Display (LCD) panel types have their advantages and disadvantages, and selecting an IPS vs VA TV depends on what use you have in mind. So, which of these panels should you use for movies?

IPS TVs have a better viewing angle than their VA counterpart. Their image accuracy remains fairly high even when I"m watching my movies from the side.

VA panels have better contrast ratios between the two panels. I like their deep blacks when watching movies in the dark. If you geek over late-night shows, go for VA as it provides more definition.

IPS TVs generally have lower contrast. When using them, I tend to see blacks displayed as gray because of IPS glow. However, the difference is hardly noticeable in brightly lit conditions.

Unlike contrast and the viewing angle, the panel type doesn"t exclusively dictate a screen"s black uniformity. Regardless, most of the VA panels I use have better black uniformity between the two panels.

This doesn"t immediately paint VA panel TVs as the winner, and you may find a better-displaying IPS. Besides, you can enhance the screen"s uniformity using the dimming function.

Displays with great color accuracy and extensive coverage of wide color gamuts like DCI-P3 or Adobe sRGB are typically made using IPS panels. You don"t necessarily need to gaze directly at an IPS monitor in order to see realistic colors because IPS displays typically appear beautiful from wider angles as well.

Although color accuracy and coverage on VA displays (even at broad angles) can be outstanding, colors aren"t always consistent. The center of VA monitors frequently has greater gamma than the screen"s edges, reducing the accuracy of colors depending on the viewer"s perspective and the distance from the display.

VA panels have completely adequate color accuracy and coverage for the great majority of users, despite the fact that IPS is typically superior to VA in these areas. A VA monitor that only covers 90% of the DCI-P3 color space is actually a very good amount of coverage for games and content consumers, with the exception of professional picture and video editors.

LCD panels function using liquid crystals which, when charged with electricity, react and change location. Based on the position, the crystals display a particular color.

PLS (Plane-to-Line Switching) is a type of IPS used on Samsung monitors (check out also Benq monitors) which perform similarly but with round-edged pixels. On the other hand, VA pixels appear like straight rectangles.

IPS panels have an RGB sub-pixel arrangement, whereas numerous VA panels feature a BGR layout. The sub-pixel layout doesn"t outrightly affect image quality, provided it"s not a PC monitor.

Some applications require an RGB arrangement. When I use a BRG VA panel in such cases, I see some slight blurriness on the text. However, adjusting my text scaling eases readability. Overall, RGB layouts don"t have this issue as much as BRG.

The majority of IPS panels offer viewing angles up to 178 degrees horizontally and vertically. Accordingly, if you"re viewing content off-center, you won"t notice much color shifting or a noticeable decrease in picture quality until you get to the very edges of the viewing angles.

Even though VA panels have improved significantly over the years in terms of viewing angles, they still fall short of IPS panels in some respects. When viewing content off-center, VA panels are often a little weaker in terms of color/contrast shifts. This is probably less of an issue for gamers, who are more likely to be seated directly in front of the monitor and not move around the monitor"s ideal viewing angle.

You"ll notice that manufacturers are trying out multiple techniques to enhance VA viewing angles while achieving a high contrast. Although this goal is a work in progress, several TVs are now available that try to encompass both these crucial attributes.

The first sets to feature a broad viewing angle got announced in 2018. Several pricey models also came out with this technology in 2020, for instance, the Sony X950H and the Samsung Q90/Q90T QLED (see our Quantum Dot vs IPS post).

While I love their recognizable improvement in viewing angles over pure VA TVs, they are still yet to achieve the level of performance you get with a pure IPS panel.

As they solve one problem, the upgraded VA panels present you with another issue. Options like the Sony X950H have noticeably lower contrast ratios than typical VA panels.

Nevertheless, I appreciate their native contrast still being higher than regular IPS panels. With their dimming feature, I still can get a deep black convenient for night movies.

Neither panel technology is inherently better because they have different functions. IPS displays are suitable for watching big games or a show across a wide sitting arrangement.

Selecting between the two panels means you"ll give up particular features. Depending on your movie needs, I believe you can decide which panel suits you.

You probably now know the most suitable panel to get, given the different specifications. As in most instances, the higher your budget (see the best budget picks), the better the panel. Here is a simple guide on the ideal panel depending on your usage:

Editing footage and pictures:IPS monitors are more favorable given their better color reproduction. Some VA panels offer wide color ranges, though they typically have motion blur

In order to understand this problem, we first need to know the panel type of LCD. At present, the LCD panels are mainly divided into three categories, which are TN, VA and IPS.

TN panel, full name Twisted Nematic (twist nematic), because the production cost is relatively low, so it is the first popular panel in LCD. The advantage of TN panel is that the response time of GTG panel is very fast, and the gray scale response time of GTG is often up to 1ms, which is the lowest among all LCD panels, so many e-sports / game monitors use TN panel.

However, the shortcomings of the TN panel are also obvious, such as less output gray scale, white color, small visual angle and so on. 1080p is the most common resolution in the TN panel, and there are also some 27-inch QHD panels, and the latest panel can do 28-inch UHD. At present, the main manufacturers of TN panels are Samsung display (Samsung Display), LG, Youda Optoelectronics, Qunchuang Optoelectronics, China Picture Tube and so on.

Let"s talk about the VA panel. VA panel full name Vertical Alignment (vertical arrangement), its advantage lies in the contrast, VA panel is the highest contrast of all LCD panels, usually can reach 3000 VA 1, while the contrast of TN, IPS is only about 1000 VA 1, the intuitive feeling of high contrast is that black looks purer and the picture is more layered.

The gray scale response time of VA panel is faster than that of IPS, and some of them even reach the same 1ms as TN, while the visual angle of TN is much better than that of TN, which is consistent with the visual angle of IPS panel, and there is no light leakage problem of VA panel.

Finally, let"s talk about the IPS panel. IPS full name In-Plane Switching (plane conversion), its advantage is that the color performance is relatively good, and the visual angle is also relatively wide, horizontal and vertical visual angle can reach 178°, but the contrast is not as good as VA panel, and the problem of light leakage is also more prominent.

From the above carding, it is not difficult to see that each panel has its own advantages, but also some inherent shortcomings. For example, TN panel is better than fast response time, but the color and visual angle is not good; VA panel contrast is high, but there are still some differences in response time and color; IPS color is good, but there are long response time and light leakage problems.

So which panel to choose depends on the specific requirements, you can"t simply think that IPS must be better than VA, or VA must be better than TN. For example, heavy players of FPS games who value response time can choose the display of TN panel, designers who value visual angle and have certain requirements for color can choose the display of IPS panel, and friends who like to watch some high-contrast and more powerful pictures can choose the display of VA panel.

I have been writing posts about the comparison of all kinds of LCD screens and their structure for a while. Only one kind of LCD screen we are doing I haven’t mentioned yet: VA LCD.

There are 7 main technical parameters for LCD screen. If I have to choose the two most important parameters to indicate the quality of LCD screen, it would be view direction (visual angle) and contrast rate. VA LCD has the best contrast rate.

It is a gray background and white letters negative display TN screen with white LED backlight. It isn’t looking so good, is it? Could background color be black instead of gray? It will look much better. Of course, it can, but then it will become VA LCD. People want to improve the view direction (visual angle) and contrast rate of LCD screen, so they invented VA LCD. In other words, VA LCD is the updated version of TN LCD. It does look good, doesn’t it? It is usually used in high-class electronic products. For example: Vehicle electronic products.

It is no doubt that the black background and white letters VA LCD is the best one. As I know, as long as it is black background and monochrome, it must be VA LCD. That is simple. Only the background color of VA LCD screen is black. In other words, black background LCD screen can’t be made into any other kinds, except VA LCD panel.

Because of its black background, it is certain that VA LCD is a negative display. And is it possible that VA LCD does not use LED backlight? Yes, it is, but it is unreasonable and illogical because VA LCD screen is so expensive, which is only applied in high-class electronic products, and LED backlight is so cheap. In my opinion, it is stupid that it doesn’t use LED backlight.

FSTN LCD does have the best view angle. It is a 12 o’clock view direction VA LCD. You can see it very clearly at 12 o’clock, 3 o’clock and 9 o’clock directions. But it is very blurred in 6 o’clock direction. On the other hand, FSTN VCD can be seen very clearly in all the directions.

It will still be good as long as it adopts transflective polarizer film even though outdoor is not the best-using condition for VA LCD panel. Please see the table below. Polarizer filmUsing conditionLED backlightstylishdisplay effect

We would only recommend using COG LCD module when it is a very small dot-matrix screen. It is a technical challenge to make VA COG dot matrix LCD module, so it is expensive.

IPS (In-Plane Switching) lcd is still a type of TFT LCD, IPS TFT is also called SFT LCD (supper fine tft ),different to regular tft in TN (Twisted Nematic) mode, theIPS LCD liquid crystal elements inside the tft lcd cell, they are arrayed in plane inside the lcd cell when power off, so the light can not transmit it via theIPS lcdwhen power off, When power on, the liquid crystal elements inside the IPS tft would switch in a small angle, then the light would go through the IPS lcd display, then the display on since light go through the IPS display, the switching angle is related to the input power, the switch angle is related to the input power value of IPS LCD, the more switch angle, the more light would transmit the IPS LCD, we call it negative display mode.

The regular tft lcd, it is a-si TN (Twisted Nematic) tft lcd, its liquid crystal elements are arrayed in vertical type, the light could transmit the regularTFT LCDwhen power off. When power on, the liquid crystal twist in some angle, then it block the light transmit the tft lcd, then make the display elements display on by this way, the liquid crystal twist angle is also related to the input power, the more twist angle, the more light would be blocked by the tft lcd, it is tft lcd working mode.

A TFT lcd display is vivid and colorful than a common monochrome lcd display. TFT refreshes more quickly response than a monochrome LCD display and shows motion more smoothly. TFT displays use more electricity in driving than monochrome LCD screens, so they not only cost more in the first place, but they are also more expensive to drive tft lcd screen.The two most common types of TFT LCDs are IPS and TN displays.

Although IPS, VA and TN displays all use LED technology (a form of LCD or Liquid Crystal Display), the picture quality and response times can vary; TN monitors do not reproduce colour as effectively as IPS and VA types, for example.

At LG, we have a range of IPS and VA panels available, so it’s worth getting to grips with the differences between these two types when you’re looking for a new monitor.

Additionally, you’ll find that the image quality isn’t compromised at different angles with an IPS monitor, which means they’re suitable for shared viewing. This is what sets them apart from TN panels, which may not offer the same kind of flexibility. Generally speaking, users have to look at TN monitors straight on for true colour accuracy.

VA (which stands for vertical alignment) displays use vertically aligned crystals that are backlit. Whilst you’ll find IPS technology in a wide range of displays, you’ll only really find VA technology in monitors and TVs.

Like IPS panels, VA monitors provide clear images, but they’re especially good – arguably the best – at displaying contrasts. We