3.2 inch tft lcd display in stock

This module is the 3.2” version of the ESP32 touchscreen display, based on ESP32-WROVER, with a built-in 2M pixel OV2640 camera. The LCD is 320x240 TFT, with driver is ILI9341, it uses SPI for communication with ESP32, the SPI main clock could be up to 60M~80M, make the display smooth enough for videos; and the camera OV2640 with pixel 2M, with this camera, you can make applications such as remote photography, face recognition…

While the camera not used, you can freely use all these pins with the breakout connectors, to connect the ESP32 display with sensors/ actuators, suitable for IoT applications.

This Nextion 3.2 inch HMI TFT  is a Seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. It is the best solution to replace the traditional LCD and LED Nixie tube.

This solution includes hardware part – a series of TFT boards and software part  – Nextion editor. Nextion TFT board uses only one serial port to do communicating. Let you get rid of the wiring trouble. We notice that most engineers spend much time in application development but get unpleasant results. In this situation, Nextion editor has mass components such as button, text, progress bar, slider, instrument panel etc. to enrich your interface design. And the drag-and-drop function ensures that you spend less time in programming, which will reduce your 99% development workloads. With the help of this WYSIWYG editor, GUI designing is a piece of cake.

NX4024T032 is a powerful 3.2” HMI, which is member of Nextion family. Features include: a 3.2″ TFT 400 x 240 resistive touch screen display, 4M Flash, 2KByte RAM, 65k colors.

Fully assembled 3.2inch display with 320x240 pixels TFT LCD and a resistive touch overlay. Just plug it on top of ODROID-C1. 2x13 tall female header is already soldered on the PCB.

-LCD control IC ILI9341, touch panel controller XPT2046; Adopt industrial TFT LCD modules; High-grade gold-plated double yellow-module pin, better electrical properties; -Compatible with all hot Atom development boards, straight into the straight; -Application is fully open source; -Bottom-driven technical support LCD, a transaction, is a friend forever;

-3.2 inch, 240*320 resolution, TFT touch screen; -Display driver IC ILI9341, touch screen driver for XPT2046; 16bit-display interface parallel interface, support for 6800 and 8080 bus interface supports STM32 FSMC bus interface, crowding the screen faster; -Touch screen interface for the SPI interface, so that the line less, driving is simple; -Onboard-a large current LDO voltage regulator, 5V and 3.3V power supply; -Onboard PWM backlight control circuit to support IO control and PWM dimming control; -Modules with SD cards, digital photo frames and other experiments can be done; -Reserved SPI FLASH pad, you can extend the welded fonts chips; -Supports landscape and portrait displays, support split the screen display; -Support for 262,000-color RGB display and displayed good quality; -Graphic display of the screen controller with internal 172800 byte data storage; Punctuality Atom-interface compatible series of interface Development Board; Patch-machine production, stable and reliable hardware;

-Module design principle; -LCD controller data manual; -XPT2046 data sheet; -Module schematic diagram; -Module dimensions; -LCD package; MOD software-text; -Picture taking mode software; -C51 code wiring tutorial; -STM32 code wiring tutorial;

The RPi LCD can be driven in two ways: Method 1. install driver to your Raspbian OS. Method 2. use the Ready-to-use image file of which LCD driver was pre-installed.

3) Connect the TF card to the Raspberry Pi, start the Raspberry Pi. The LCD will display after booting up, and then log in to the Raspberry Pi terminal,(You may need to connect a keyboard and HDMI LCD to Pi for driver installing, or log in remotely with SSH)

1. Executing apt-get upgrade will cause the LCD to fail to work properly. In this case, you need to edit the config.txt file in the SD card and delete this sentence: dtoverlay=ads7846.

This LCD can be calibrated through the xinput-calibrator program. Note: The Raspberry Pi must be connected to the network, or else the program won"t be successfully installed.