arduino 3.5 tft lcd shield library factory
I bought a new TFT lcd shield, and it controller model is ILI9486 (Figure is Attached). However, many libraries are not working on it such as (UTFT and URTouch).
I then downloaded the (mcufriend_kbv) library; it worked well for drawing shapes specifying their dimensions; so the library equivalent to the UTFT library is solved. However, the accompanied examples are only working with arduino UNO, in the time I"m using Arduino Mega R3.
My main problem now is finding a library equivalent to the (URTouch), because for now nothing is working (even Touchscreen library). So, could you give me a hint to solve this problem ?
Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (3.5" diagonal) bright (6 white-LED backlight) and colorful (18-bit 262,000 different shades)! 320x480 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel with controller XPT2046 attached by default and a optional capacitive touch panel with controller FT6236 attached by default, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover.
The pin32 (SDO) of 3.5 display module is also used by touch panel or SD card SPI interface, so we must cut off this pin to avoid conflict with the touch panel or SD card.
The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (Due/Mega 2560).
This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.
Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!
If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.
TFT LCDs are the most popular color displays – the displays in smartphones, tablets, and laptops are actually the TFT LCDs only. There are TFT LCD shields available for Arduino in a variety of sizes like 1.44″, 1.8″, 2.0″, 2.4″, and 2.8″. Arduino is quite a humble machine whenever it comes to process or control graphics. After all, it is a microcontroller platform, and graphical applications usually require much greater processing resources. Still, Arduino is capable enough to control small display units. TFT LCDs are colorful display screens that can host beautiful user interfaces.
Most of the smaller TFT LCD shields can be controlled using the Adafruit TFT LCD library. There is also a larger TFT LCD shield of 3.5 inches, with an ILI9486 8-bit driver.
The Adafruit library does not support the ILI9486 driver. Actually, the Adafruit library is written to control only TFT displays smaller than 3.5 inches. To control the 3.5 inch TFT LCD touch screen, we need another library. This is MCUFRIEND_kbv. The MCUFRIEND_kbv library is, in fact, even easier to use in comparison to the Adafruit TFT LCD library. This library only requires instantiating a TFT object and even does not require specifying pin connections.
TFT LCDs for ArduinoUser interfaces are an essential part of any embedded application. The user interface enables any interaction with the end-user and makes possible the ultimate use of the device. The user interfaces are hosted using a number of devices like seven-segments, character LCDs, graphical LCDs, and full-color TFT LCDs. Out of all these devices, only full-color TFT displays are capable of hosting sophisticated interfaces. A sophisticated user interface may have many data fields to display or may need to host menus and sub-menus or host interactive graphics. A TFT LCD is an active matrix LCD capable of hosting high-quality images.
Arduino operates at low frequency. That is why it is not possible to render high-definition images or videos with Arduino. However, Arduino can control a small TFT display screen rendering graphically enriched data and commands. By interfacing a TFT LCD touch screen with Arduino, it is possible to render interactive graphics, menus, charts, graphs, and user panels.
Some of the popular full-color TFT LCDs available for Arduino include 3.5″ 480×320 display, 2.8″ 400×200 display, 2.4″ 320×240 display and 1.8″ 220×176 display. A TFT screen of appropriate size and resolution can be selected as per a given application.
If the user interface has only graphical data and commands, Atmega328 Arduino boards can control the display. If the user interface is a large program hosting several menus and/or submenus, Arduino Mega2560 should be preferred to control the TFT display. If the user interface needs to host high-resolution images and motions, ARM core Arduino boards like the DUE should be used to control the TFT display.
MCUFRIEND_kbv libraryAdafruit TFT LCD library supports only small TFT displays. For large TFT display shields like 3.5-inch, 3.6-inch, 3.95-inch, including 2.4-inch and 2.8-inch TFT LCDs, MCUFRIEND_kbv library is useful. This library has been designed to control 28-pin TFT LCD shields for Arduino UNO. It also works with Arduino Mega2560. Apart from UNO and Mega2560, the library also supports LEONARDO, DUE, ZERO, and M0-PRO. It also runs on NUCLEO-F103 and TEENSY3.2 with Sparkfun Adapter. The Mcufriend-style shields tend to have a resistive TouchScreen on A1, 7, A2, 6 but are not always in the same direction rotation. The MCUFRIEND_kbv library can be included in an Arduino sketch from the library manager.
The 3.5-inch TFT LCD shield needs to be plugged atop the Arduino board. The Mcufriend-style shields are designed to fit into all the above-mentioned Arduino boards. The shields have a TFT touch screen that can display colorful images and interfaces and a micro SD card reader to save images and other data. A 3.5-inch TFT LCD touch screen has the following pin diagram.
The liquid crystal display module based on SPI communication interface, provide 3.5 "TFT LCD, resistive touch screen, built-in Flash flash and SD card external expansion storage. This TFT panel connects directly on top of an Arduino pin compatible device.
2.Extract the content to your Arduino library folder. In Windows this is usually located in Arduino IDE folder\libraries. Check Arduino"s official guide if you want more information on how to install the Arduino Library The official guide of Arduino
3.Start Arduino IDE, you can find ready to run Examples in the menu. File--> Examples-> DmTftLibraries. select the right board and COM port: DM-TFT35-107
This module is a 3.5-inch TFT LCD module with “320X480” resolution and 65K color display. It is suitable for Arduino Uno and Mega2560 development boards, and also supports SD card expansion function. It uses 8-bit parallel port communication, and the driver IC is ILI9486.
The 3.5-inch display is a ready-made shield for Arduino Uno, which can also be placed on the Arduino Mega. The pins of this shield are designed to be easily installed on the Arduino. The bad point about these modules is that they use all Arduino Uno pins.
my_lcd.Fill_Triangle(x_spec+i*side_len-1,y_spec+(i+1)*h_len-1,x_spec+side_len/2+i*side_len-1,y_spec+i*h_len-1,x_spec+(i+1)*side_len-1,y_spec+(i+1)*h_len-1);
my_lcd.Fill_Triangle(x_spec+i*side_len-1,y_spec+(5-i)*h_len-1,x_spec+side_len/2+i*side_len-1,y_spec+(4-i)*h_len-1,x_spec+(i+1)*side_len-1,y_spec+(5-i)*h_len-1);
my_lcd.Draw_Line(2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34),2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34));
my_lcd.Draw_Rectangle(2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34),2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34));
my_lcd.Draw_Round_Rectangle(2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34),2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34),5);
my_lcd.Draw_Triangle(2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34),2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34),2+random(my_lcd.Get_Display_Width()-4),17+random(my_lcd.Get_Display_Height()-34));
my_lcd.Fill_Round_Rectangle(my_lcd.Get_Display_Width()/2-1-120+1, my_lcd.Get_Display_Height()/2-1-60+1, my_lcd.Get_Display_Width()/2-1+120-1, my_lcd.Get_Display_Height()/2-1+60-1,5);
Some people say that this shield requires 3.3 [Volts] to work, but the Vcc pin connected goes to 5V and it contains a Voltage regulator. I suppose it drops the voltage from 5[V] to 3.3[V] in the middle of the back side of the screen shield (see the upper photo - U1).
After using the geometry test included in the library folder UTF Geometry mentioned on #5, and using all the drivers found in the documentation included by Henning Karlsen in a .pdf doc, I couldn"t get this shield to work.
This kind of display form has two main characteristics, one is a thin film transistor, the other is TFT LCD itself. Let’s talk about the TFT screen itself. 1. working principle of the TFT-LCD screen We usually think of substances like water as three states, solid-liquid, and gas.
Dec 07, 2015 · Parts needed for this Arduino Touch Screen. As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V..
The TFT display communicates with the Arduino via SPI communication, so you need to include the SPI library on your code. We also use the TFT library to write and draw on the display. #include
Using the ILI9341 TFT & XPT2046 Touch with ESP32 & Arduino This is a quick Arduino tutorial using ILI9341 2.8 inch TFT LCD with the XPT2046 Touch controller. UPDATED FEB 26 2021!! Intermediate Protip 3 hours 21,868 Things used in this project Story Resistive or Capacitive Touch ? Well you might ask what kinds of applications can these be used in?. TFTLCD is a variant of a liquid-crystal display(LCD) that uses thin-film-transistor (TFT) technology to improve image qualities such as addressability and contrast. A TFTLCD is an active matrix LCD, in contrast to passive matrix LCDs or simple, direct-driven LCDs with a few segments. In Arduino-based projects, the processor frequency is low.. the things that I want to display: 2 temp sensors. 2 ultrasonic sensor values in cm. 1 voltage sensor. 2 amp sensor. RGB remote (with a button to chage to that screen) I am.
Arduino TFT Display $ 14.50 Orient Display – offers Arduino TFT display and Arduino display modules with top-notch technology at attractive prices. Orient Display is a company that specializes in manufacturing TFT display Arduino electronics with competitive price.. The parameters of this object depend on the model of the TFT screen and shield, and these details can be also found in the documentation of the libraries. Next, we need to.
The Arduino& TFT screen has to be voltage-free when assembling the SD card. ArduinoCode Copy the Arduinocode below & upload it to your Arduino. End result Open the serial monitor in your Arduinoprogram. Your .bmp image is now displayed on the TFTscreen. Or watch the video for the result. Code. Download Arduino IDE. Open main.ino file and upload the code into arduino board. Attach tft display to arduino board. Run your Arduino :).
Here is an UART TFT LCD, it supports WYSIWYG editor to build your GUI in PC and download it via USB. It can be controlled by Arduino via UART, so just use the Serial.print () you can make it display many images. And you can even build Font by yourself and download to the LCD. Product Description. 2.8-inch color screen,support 65K color display , display rich colors. 320X240 resolution, optional touch function. Using the SPI serial bus, it only takes a few IOs to illuminate the display . Easy to expand the experiment with SD card slot. Provide a rich sample program. Military-grade process standards, long-term stable work. Introduction: Arduino TFT LCD Touchscreen Calculator Hi Guys in this instructables we will learn how to make a calculator using Arduino Uno with 3.5″ TFT LCD Touchscreen display. So we will write a code and Upload it to arduino which will display the calculator interface on the display and will take touch functionality and give the output of basic mathematical expressions.
The project uses an Arduino Mega 2560 and UNO R3 2.8 TFT Touch Screen to display two analog signals as line and bar graphs. One signal is a photo resistor and the second is an audio sample from an Adafruit Electret Microphone Amplifier with Adjustable Gain module.
This library enables an Arduino board to communicate with an Arduino TFT LCD screen. It simplifies the process for drawing shapes, lines, images, and text to the screen. The Arduino TFT library extends the Adafruit GFX, and Adafruit ST7735 libraries that it is based on. The GFX library is responsible for the drawing routines, while the ST7735. In diesem Video zeige ich euch wie man ein TFT Display mit Hilfe eines Arduinos ansteuern kann.Das TFT-Display kannst du hier bestellen:https://www.amazon.de. Follow the steps below to write ‘Hello World’ on the TFT screen: Connect evive to your laptop/PC, and select the appropriate port. Add evive library in your Arduino IDE; it has a lot of functions.
SainSmart 1.8″ Color TFT LCD Display for Arduino. The display has back-light and comes with a Micro-SD-Card reader (supporting FAT16 or FAT32 formatted Micro-SD-Cards). The display is driven by a ST7735R controller ( ST7735R-specifications.pdf (2.1 MB) ), can be used in a "slow" and a "fast" write mode, and is 3.3V/5V compatible. .
TFT Library for Arduino This library enables an Arduino board to communicate with the Arduino TFT LCD screen. It simplifies the process for drawing shapes, lines, images, and text to the screen. For more information about this library please visit us at http://www.arduino.cc/en/Reference/TFTLibrary.
TFT screens never work. Hello, I am trying to use these cheap duinotech / altronics 128x128 1.44" TFT screens. When I run the example, some color noise appears on the screen briefly, but it stays lit and blank after that. This same setup has worked for me in the past but now I can"t get any of them to work at all. Tft lcd arduino. Arduino expansion board Arduino can be connected to LED Tft lcd arduino. Arduino expansion board Arduino can be connected to LED, LCD, buttons, stepping motor, steering gear, temperature and humidity sensor, distance sensor, pressure sensor [] 09/24/2022.
WeatherPi_ TFT is a Python library typically used in Internet of Things (IoT), Raspberry Pi, Pygame applications. WeatherPi_ TFT has no bugs, it has no vulnerabilities, it has build file available and it has low support. ... # TFT display and touch panel dtoverlay=rpi- display dtparam=rotate=0 install and configure WeatherPi_ TFT . Copy. Download. Run Graphics Test. Restart the Arduino IDE. You should now be able to select File → Examples → Adafruit_ILI9341 → graphicstest sketch. Upload the sketch to your Arduino wired as before. Once uploaded, the Arduino should perform all the test display procedures!. WeatherPi_ TFT is a Python library typically used in Internet of Things (IoT), Raspberry Pi, Pygame applications. WeatherPi_ TFT has no bugs, it has no vulnerabilities, it has build file available and it has low support. ... # TFT display and touch panel dtoverlay=rpi- display dtparam=rotate=0 install and configure WeatherPi_ TFT . Copy. Download.
This Arduino tutorial shows how to interface the Uno board with ILI9341 TFT display. The ILI9341 TFT module contains a display controller with the same name: ILI9341. It’s a color display that uses SPI interface protocol.
This 2.8 inch TFT Touch Screen is professional and practical for UNO R3, TFT touch screen with an SD card socket, which can be used for the Arduino board module. 1.Compatible with Arduino UNO and Mega2560, and can be connected directly by inserting the pin into the interface without wire. 2.Compatible with all kinds of 5V or 3V MCU with a 5V-3..
How To Connect The TFT Display To The Arduino UNO? Step 1: Let us begin with the TFT display. There are pins on either side of the board. On the right-hand side, you have... Step. 1. Arduino UNO. 2.2.4 Inch TFT LCD Dsiplay. 3.some hook up wires / connecting wires. 4.led/ relay board. the above hardware can be available from any online store, you want... connect the led"s to pin 13,12 or if you are using relay board connect relay 1, relay 2 to pin 13, pin 12 respectively. Add Tip..
The Arduino TFT screen is a backlit TFT LCD screen with a micro SD card slot in the back. You can draw text, images, and shapes to the screen with the TFT library. The screen"s pin layout is designed to easily fit into the socket of an Arduino Esplora and Arduino Robot, but it can be used with any Arduino board. The TFT library is included with Arduino IDE 1.0.5 or later. Library.
Roughly measured ELEGOO UNO R3 2.8 Inches TFT Touch Screen with the basic geometries. I don"t know if the geometry is right for every produced ELEGOO 2.8" Touch Screen as the display seems to tilt a little. liheap arkansas online application. tcl 50 inch tv. probiotics 300 billion cfu; instituto de estudios fiscales campus virtual; flange bolt calculator. Jan 15, 2019 · JR. January. Digital spirit level: ADXL345, TFT Display (HY-1.8 SPI) and an Arduino; Arduino RGB LED strip control with MOSFETs and optocouplers - Part 1 - The Hardware; A RGB LED Library for Arduino; A TLC5940, 5 RGB-LEDs and an Arduino; An image slideshow with an Arduino and a tft display with a sd card module; PIC32-Pinguino-Micro - Getting Started. the things that I want to display: 2 temp sensors. 2 ultrasonic sensor values in cm. 1 voltage sensor. 2 amp sensor. RGB remote (with a button to chage to that screen) I am willing to make funtions to change the screen data values using buttons or just buy a bigger one off amazon. the TFT:. Arduino uno with ST7789 IPS TFT display. Interfacing Arduino UNO with ST7789 TFT circuit: Project circuit schematic diagram is shown below. The ST7789 display module.
2. MCU Friend TFT Display Library: mcufriend_kbv; Adafruit_GFX; Dependencies Libraries (Touchscreen etc) Open Arduino IDE. Go to Sketches > include library > Manage Libraries > Type library name > install. Know more about how to add library in Arduino IDE. Circuit for 12 Hour Format Real Time Clock with TFT Display:.
the things that I want to display: 2 temp sensors. 2 ultrasonic sensor values in cm. 1 voltage sensor. 2 amp sensor. RGB remote (with a button to chage to that screen) I am. Arduino TFT display is the subcategory that includes all the tft lcd display modules with arduino shields,libraries and examples. Our factory would be closed from Oct-1 to Oct-7 for National Day.Orders during this period would be delayed for shipment.We"ll be back on Oct-8-2022..
. You say you want to hook up a TFT display to an Arduino? Are you joking? No! For about the price of a familiar 2x16 LCD, you get a high resolution TFT display. For as low as $4 (shipping included!), it"s possible to buy a small, sharp TFT screen that can be interfaced with an Arduino. Moreover, it can display not just text, but elaborate graphics.
This Arduino tutorial shows how to interface the Uno board with ILI9341 TFT display. The ILI9341 TFT module contains a display controller with the same name: ILI9341. It’s a color display that uses SPI interface protocol. The TFT display communicates with the Arduino via SPI communication, so you need to include the SPI library on your code. We also use the TFT library to write and draw on the display. #include
The ILI9341 TFT module contains a display controller with the same name: ILI9341. It"s a color display that uses SPI interface protocol and requires 4 or 5 control pins, it"s low cost and easy to use. The resolution of this TFT display is 240 x 320 which means it has 76800 pixels.
The 10.1 inch TFT LCD Module and Arduino is powered up using a 12v adaptor or battery. All the grounds are connected together. The DIN pin of the TFT LCD module which is data-in is connected with the TX pin of the MAX232, the DOUT pin which is the data-out pin is connected with the RX pin of the DB9. TFT which is used in the tutorial is 2.4′ TFT by Mcufriend. It has ST7781 controller in it, Driver code is ST7783. This 2.4 inch TFT Lcd is arduino compatible. It can easily be mounted on an Arduino uno board. This TFT can be interfaced in 32,16 and 8 bit parallel mode. It also supports I2c Mode. Arduino TFT Display $ 10.50 Compare 1.3″ IPS display, 240×240, 470 Nits, MCU/SPI/RGB Interface Color TFT $ 18.18 Sold out Compare 1.3″ Round IPS display, 240×240, 450 Nits, MCU/SPI/RGB Interface Color TFT $ 13.28 Compare 1.44″ Arduino TN TFT, 128×128, 300 Nits, 4-wire SPI Interface Arduino TFT Display $ 9.21 Compare.
Arduino UNO 1 2.4 TFT LCD display 1 Apps and online services Arduino IDE About this project In the home screen, there are three buttons.When a touch is sensed on a button, I fill the button with white colour, wait a bit and draw it again with. Re: How to clear a 2.8 tft touch screen with capacitive touc. by adafruit_support_mike » Tue Jan 19, 2016 10:15 pm. Use .drawRect () with the background color to erase the area you want to clear. Rayala16.
Sep 24, 2022 · the things that I want to display: 2 temp sensors. 2 ultrasonic sensor values in cm. 1 voltage sensor. 2 amp sensor. RGB remote (with a button to chage to that screen) I am willing to make funtions to change the screen data values using buttons or just buy a bigger one off amazon. the TFT:.
The ST7735 TFT works with 3.3V and the Arduino uno works with 5V, supplying the TFT control lines directly with 5V my damage it, so we have to add the five 1K ohm resistors. The ST7735 board is supplied with 5V which. Run Graphics Test. Restart the Arduino IDE. You should now be able to select File → Examples → Adafruit_ILI9341 → graphicstest sketch. Upload the sketch to your Arduino wired as before. Once uploaded, the Arduino should perform all the test display procedures!.
The TFT library is included withArduino IDE 1.0.5 and later. This library enables anArduino board to communicate with theArduino TFT LCDscreen. It simplifies the process for drawing shapes, lines, images, and text to thescreen. TheArduino TFT library extends the Adafruit GFX, and Adafruit ST7735 libraries that it is based on. The GFX library is responsible for the drawing routines, while the ST7735 library is specific to the screen on the Arduino TFT..
Arduino TFT Display $ 10.50 Compare 1.3″ IPS display, 240×240, 470 Nits, MCU/SPI/RGB Interface Color TFT $ 18.18 Sold out Compare 1.3″ Round IPS display, 240×240, 450 Nits, MCU/SPI/RGB Interface Color TFT $ 13.28 Compare 1.44″ Arduino TN TFT, 128×128, 300 Nits, 4-wire SPI Interface Arduino TFT Display $ 9.21 Compare. Sep 24, 2022 · the things that I want to display: 2 temp sensors. 2 ultrasonic sensor values in cm. 1 voltage sensor. 2 amp sensor. RGB remote (with a button to chage to that screen) I am willing to make funtions to change the screen data values using buttons or just buy a bigger one off amazon. the TFT:.
Arduino UNO 1 2.4 TFT LCD display 1 Apps and online services Arduino IDE About this project In the home screen, there are three buttons.When a touch is sensed on a button, I fill the button with white colour, wait a bit and draw it again with. ILI9163C 1.44″ TFT Display. The ILI9163C based 1.44″ colored display with a resolution of 128 x 128 pixels. It’s capable of displaying up to 262,000. The tft.readID function reads ID from the display and put it in ID variable. Then tft.begin function gets ID and the LCD gets ready to work. Resolution of the Display. Popular sizes of Arduino displays such as 3.5 inch 480×320, 2.8 inch 400×240, 2.4 inch 320×240 and 1.8 inch 220×176. Color of the Screen tft.fillScreen(t);.
This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (16-bit 262,000 different shades)! 240x320 pixels with individual pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it. brain test level egv 33 pack chica nude.
TFT screens never work. Hello, I am trying to use these cheap duinotech / altronics 128x128 1.44" TFT screens. When I run the example, some color noise appears on the screen briefly, but it stays lit and blank after that. This same setup has worked for me in the past but now I can"t get any of them to work at all.
This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (16-bit 262,000 different shades)! 240x320 pixels with individual pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it. brain test level egv 33 pack chica nude.
This is a 3.5-inch 320 * 480 resolution TFT colour screen. It supports working boards such as Arduino Uno and Arduino mega2560 and Arduino due. Also supports STM32, 51 and other conventional microcontrollers.
When using this screen, you do not need any wiring operations, just plug onto your Arduino board, we will provide the corresponding Arduino library files, the development code is open source, you can use Arduino and this screen to build some awesome applications and games!
This 3.5 inch TFT LCD is based on the ILI9481 LCD driver and gives a very sharp/nice picture quality and works amazing well with Arduino Uno and Arduino Mega Microcontrollers. Unfortunately this display is not a touchscreen display, however it makes it up with the included MicroSD Card Slot. No soldering, no wiring, no fuss just plug and play!
Ms.Josey 
Ms.Josey