tft display with sd card price

This ST7735S 1.8" TFT Display features a resolution of 128×160 and SPI (4-wire) communication. Integrated with an SD card slot, it allows you to easily read full-color bitmaps from the SD card.

The module provides users with two wiring methods: pin header wiring and GDI (General Display interface). You can directly connect the display to a FireBeetle main controller using an FPC cable. Plug and play, easy to wire. Besides, the display supports a low refresh rate and offers a good display effect and strong versatility.

Just tested the 2.2″ version. Easiest way to control it from an Arduino is by using the Adafruit ILI9340 library. Made a video of the example sketch that comes with the library: http://www.youtube.com/watch?v=bVzZ6PWFbGE

Thanks for the feedback, I have tested it on 5V, it seems no problem for testing, for the LED backlight it has to be 3V3, or 5V with 10K resistor, for the VCC, not sure which have to be used. It seems the factory provided info it not fully promising.

The 2.2″ version is perfect for displaying complex information due to the 320×240 pixel area. Power consumption is reasonable. Be aware of the 3.3V levels since 5 volts will destroy your display (sooner or later). Most ARM boards will come with 3.3V levels anyway and even Atmel ATmega will work on 3.3 volts (but with lower frequency)

nice unit. got the 2.2″ version for my signal generator project (based on the AD9850 module i got from here also). clean and clear, very happy with it.. got it working with a couple of different libraries, mainly Adafruit and UTFT.

2.2” – Nice colors, easy integration with Arduino Uno and Teensy++2.0 . Only 3 stars because of the limited angle of view and issues withh the edge most lines.

2.2” display – Nice colors, easy integration with Arduino Uno and Teensy++2.0 . Only 3 stars because of the limited angle of view and issues with the edge most lines.

The screen is 1.77" diagonal, with 160 x 128 pixel resolution. The TFT library interfaces with the screen"s controller through SPI when using the TFT library. Refer to the screen"s data sheet for complete details.

The Arduino TFT library extends the Adafruit GFX, and Adafruit ST7735 libraries that it is based on. The GFX library is responsible for the drawing routines, while the ST7735 library is specific to the screen on the Arduino screen. The Arduino specific additions were designed to work as similarly to the Processing API as possible.

The TFT library relies on the SPI library, which must be included in any sketch that uses the scree. If you wish to use the SD card, you need to include the SD library as well.

ER-TFTM070-7 is 800x480 Pixels 7 inch color tft lcd display module with LT7683 controller board,superior display quality and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO, and ARM .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 6800 8-bit,16-bit parallel,3-wire,4-wire,I2C serial spi interface.Built-in MicroSD card slot.It"s optional for resistive touch panel and controller XPT2046,capacitive touch panel and controller FT5316, flash chip and microsd card. We offer two types connection,one is pinheader and the another is ZIF connector with flat cable mounting on board by default and suggested.

It"s optional for flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" We prepared the interfacing documents,libraries and examples for arduino due,mega 2560,uno,For 8051 microcontroller user,we also prepared the interfacing document and demo code.

This ST7735S 1.8" TFT Display features a resolution of 128×160 and SPI (4-wire) communication. Integrated with an SD card slot, it allows to easily read full-color bitmaps from the SD card.

The module provides users with two wiring methods: pin header wiring and GDI (General Display interface). You can directly connect the display to a FireBeetle main controller using an FPC cable. Plug and play, easy to wire. Besides, the display supports a low refresh rate and offers a good display effect and strong versatility.

The 2.2 inch TFT display is equipped with an ILI9341 driver and can easily be accessed using the SPI port of your Arduino or microcontrollers. The LCD module has a QVGA resolution and displays 320 x 240 pixels with a range of 262,000 colors.

This awesome little display breakout is a great way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

This 2.2″ display has 320×240 color pixels and is a true TFT display. The TFT driver (ILI9340 or compatible) can display full 18-bit color (262,144 shades). The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. Adafruit also had a little extra space on the back so there is a microSD card holder for easily loading full-color bitmaps from a FAT16/FAT32 formatted microSD card.

The Adafruit 2.2″ TFT LCD with MicroSD Card also features an EYESPI connector for a simpler connection to the LCD. EYESPI is a single 18-pin FPC used as a quick way to connect displays.

Thank you for your purchase. We hope you are happy with your purchase. However, if you are not completely satisfied with your purchase for any reason, ELEGOO provides a straightforward warranty that is processed in the most hassle-free way possible. Please refer to the chart below for the warranty timelines of various products, as warranty periods differ according to models.

All returns for refund must be postmarked within fourteen (14) days of the date the item was delivered to the designated shipping address. All returned items must be in new and unused condition, with all parts & accessories included and all original tags and labels attached.

All returns for exchange must be postmarked within thirty (30) days of the date the item was delivered to the designated shipping address. All returned items must be in new and unused condition, returned with all parts & accessories included and all original tags and labels attached.

A 1.8 inch TFT LCD display is a small color display that can be used to display text, graphics, and video. The display is typically connected to a microcontroller or other device that provides the data to be displayed.

A 1.8 inch TFT LCD display and SD card module is a combination of a 1.8 inch TFT LCD display and a Secure Digital (SD) card reader, which allows the display to show images and videos stored on an SD card. The module typically has a connector for the LCD display, a connector for the SD card reader, and a set of pins or a connector for the microcontroller.

To use a 1.8 inch TFT LCD display and SD card module with an Arduino, you will need to install a library for the display and connect the module to the Arduino using a suitable connector or set of wires. The library will provide functions for controlling the display and reading and writing data to the SD card.