tft lcd 2.4 arduino uno brands
The shield connects ILI9341"s data pins 0-7 to Arduino digital pins 2-8 (allowing parallel communication, not SPI). ILI"s RESET goes to pin to Arduino analog pin A4.CS (chip select) to A3. RS (CD command/data) to A2. WR and RD to A1 and A0.
The touch screen is attached on the surface of the display. It connects through 4 wires, which share arduino pins 8, 9, A2, A3 with ILI. So you can"t write to LCD display and read the touch screen in the same time.
First we need to detect if there is a touch. So we connect both wires of one layer/membrane, e.g. X to ground (LOW from ardiuno pins set as output) and one wire from layer Y to pull-up resistor (setting corresponding arduino pin as INPUT_PULLUP). Reading the second wire of Y layer we get HIGH if there is no touch (because of pull-up) and LOW if there is a touch (because of contact with grounded X layer).
As I can read your link, the shield is using D2-D8 and A0-A3, leaving some pins unused. So some Arduino pins are still free to use, just the shield is in the way to get connected there.
create intermediate shield (there are many, which allow you connect to arduinou on bottom and stack antother shield on top, draw your wires from there (and maybe even put some circuities on the middle shield, if you want
(something like this https://www.aliexpress.com/item/UNO-Prototype-DIY-shield-kit-for-Arduino-UNO-Universal-Extend-Board-UM-UNO/32555004112.html or any "arduino universal shield"
use pins D10-D13 as they are connected also to ISP header https://www.arduino.cc/en/Tutorial/ArduinoISP and could be connected from there. As they are part of SPI interface
It is possible to connect more arduinos, there are so much different ways, that it is hard to write here all - choose one, that would suit you best. (anyway you would need some access to some pins anyway )
The 2.4 inch TFT LCD Touch Display Shield for Arduino Uno is fully assembled, tested and ready to go. Add the touch display without wiring, no soldering! Simply plug it in and load up a library – you ‘ll have it running in under 10 minutes! Works best with any classic Arduino ATMEGA328 Board
So spice up your Arduino UNO project with a beautiful large touchscreen display shield with a built-in microSD card connection. This TFT display is big (2.4″ diagonal) bright (4 white-LED backlights) and colorful (18-bit 262,000 different shades)!
This shield with graphic LCD 2.4 "" touchscreen is perfect for your projects. It has a resolution of 320x240 pixels. Shield contains a resistive touchscreen type. It contains a slot for SD cards that can load images in .bmp format to display them on display. Specifications 320 x 240 resolution Based on SPFD5408 controller (compatible with ILI9341) 8-bit digital interface control + 4 lines LDO voltage regulator 3.3 V Integrated Compatible with 5V microcontrollers and 3.3 V 18-bit color (up to 262,000 colors supported) SD card slot 4-wire resistive touchscreen
This is a 3.5-inch 320 * 480 resolution TFT color screen. It supports working boards such as Arduino uno and Arduino mega2560 and Arduino due. Also supports STM32, 51 and other conventional microcontrollers.
When using this screen, you do not need any wiring operations, just plug onto your arduino board, we will provide the corresponding Arduino library files, the development code is open source, you can use arduino and this screen to build some applications.The backlight always on, can not control the backlight, backlight is connect to 3.3V.
This module is designed to plug directly into Arduino UNO R3 (or its clone) boards. It is compatible with CH340 and Atmega16u2 version boards, as well as Mega 2560. This LCD shield may also work with other boards, but the compatibility can"t be guaranteed.