tft lcd 2.4 arduino uno for sale

Spice up your Arduino project with a beautiful touchscreen display shield with built in microSD card connection. This TFT display is 2.4" diagonal and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. As a bonus, this display has a optional capacitive touch panel and resistive touch panel with controller XPT2046 attached by default.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Due/Mega 2560).

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.4″ diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240×320 pixels with individual pixel control. It has way more resolution than a black and white 128×64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

2.4 inch TFT LCD Touch Screen Shield for Arduino UNO R3 Mega2560The shield is fully assembled, tested and ready to go. No wielding, no solder! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic UNO. This shield does work with the Mega but its going to be half the speed of the Uno-type boards because of the way the Mega rearranges all the pins (there is no way to get around this!) This shield is Leonardo-compatible

Description:Spice up your project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.4 inch diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.color: redMaterial: comprehensive material

Technical Details:2.4 inch diagonal LCD TFT display240x320 resolution, 18-bit (262,000) colorspfd5408 controller with built in video RAM buffer8 bit digital interface, plus 4 control linesUses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if using the microSDWorks with any "328 or Mega (Leonardo supported yet)5V compatible! Use with 3.3V or 5V logicOnboard 3.3V 300mA LDO regulator4 white LED backlight. On by default but you can connect the transistor to a digital pin for backlight control4-wire resistive Press screenPackage Contents:1* 2.4 inch TFT LCD screen1* Pen

Thanks for the reply. I had searched through this forum. many of the data is for 2.4 inch TFT Touchscreen interface with UNO and mega only. one of the search result tells that the Arduino due is 3.3V and 2.4 inch TFT is 5V compatible. Some result tells that Arduino due can interface with 2.4 inch TFT. So i am confused in it. Before buying the boards and i have to confirm that the Arduino due can interface with 2.4 inch tft touchscreen Lcd shield?