lcd screen coating repair quotation

The display on my 2012 E70 CPO w/ only 13K miles was looking pretty shabby--like many of you have experienced, the anti-glare coating was worn away, probably from an attempt to clean the display. I thought about taking it to the dealer and arguing for replacement of the $2K display, but then I thought it would likely happen again over time because the anti-glare coating is so fragile. So I decided to take the advice of some of you in this forum and apply a screen protector. In my case, I chose to remove the remaining anti-glare coating because it would likely do more harm than good if left in place.

I decided that doing a proper job would be too difficult to do with the screen in the car, so I elected to remove my display. It wasn"t very difficult. I found a YouTube video with instructions that were quite helpful:

I bought the Novus Plastic polish kit recommend here on this forum from Amazon, and began by cleaning the display with bottle #1, "Plastic Clean & Shine." That didn"t remove the blotchy anti-glare coating, so I used bottle #2, "Fine Scratch Remover," and that worked great. I followed the instructions and used a circular motion with the included wipes, and it cleaned up the display quite nicely. Basically, it looked new. I also used a Q-Tip to get around the edges and in the corners. Once that was done, I polished the display again with the "Plastic Clean & Shine."

Next, it was time to apply the screen protector. I decided to buy a protector from Nushield (www.nushield.com) because I saw that others that had purchased the Lexerd protector had to trim it down. Nushield didn"t list a protector for my 2012 E70, but customer service was very helpful and the 2011 protector turned out to be the correct size. I purchased some of Nushield"s Step 1 wet wipes with my protector, and I cleaned the screen with that and then dried and polished the screen with their included cloth. I then blew off any residual dust particles with some "canned air," available at any office supply store.

The quality of the film seems to be very high, and the screen now looks great--really, better than new. I turned on the car, and the display looked wonderful! Extremely sharp and glare-free, and free of the ugly blotchiness that was so bothersome. And now I can clean my display worry free because it has no fragile coating.

I bought a Sony RX1R camera a few years back and it all works fine but when the LCD plastic sheet that was (ahem) "protecting" the LCD screen came off, I was rather horrified to see that the screen coating seems to have been damaged.

It doesn"t really notice when the screen is turned on but as I"ve upgraded my camera I"d like to sell the Rx1R - and obviously having a LCD screen like this is going to knock the price down!

Responsible for performing installations and repairs (motors, starters, fuses, electrical power to machine etc.) for industrial equipment and machines in order to support the achievement of Nelson-Miller’s business goals and objectives:

• Perform highly diversified duties to install and maintain electrical apparatus on production machines and any other facility equipment (Screen Print, Punch Press, Steel Rule Die, Automated Machines, Turret, Laser Cutting Machines, etc.).

• Provide electrical emergency/unscheduled diagnostics, repairs of production equipment during production and performs scheduled electrical maintenance repairs of production equipment during machine service.

LCD problems usually occur after your camera has been dropped, subjected to impact, or has experienced some sort of excessive moisture or liquid damage. The symptoms that you’ll typically see are: a cracked or shattered look, a totally black screen, or a distorted picture.

If your screen is cracked or damaged unfortunately the only way to fix this is to physically replace the LCD screen. There are things that you can do to protect your LCD screen from being scratched or damaged. First thing is to always store your camera in a protective camera case. Using a screen protector can also help protect your LCD screen from scratches. With this type of problem, prevention is the only way to stop this part of the camera from being damaged.

This is a fairly straightforward repair. We replace the LCD screen and then fully clean and service your camera. We only use original Sony parts with this repair. We have seen generic screens out there which can be cheaper however, they are inferior in picture quality and durability.

Fill out the Repair Order Form and ship the camera to us for a free estimate. If you have any questions before sending your camera in for repair we welcome you to call and talk to one of our experienced Sony technicians. 888-283-2228

Use this guide along with an oleophobic coating kit to restore the oleophobic coating on your device, or to add an oleophobic coating to your screen or screen protector. These kits can also be used to treat other glass surfaces, such as eye glasses, watches, smartwatches, and more.

Modern smartphones feature an oleophobic (oil-repellent) coating that protects the screen, improves smoothness, and reduces fingerprints. This coating consists of a thin layer of fluoropolymer-based solids (similar to Teflon) that is bonded to the glass.

Use this guide along with an oleophobic coating kit to restore the oleophobic coating on your device, or to add an oleophobic coating to your screen or screen protector. These kits can also be used to treat other glass surfaces, such as eye glasses, watches, smartwatches, and more.

Modern smartphones feature an oleophobic (oil-repellent) coating that protects the screen, improves smoothness, and reduces fingerprints. This coating consists of a thin layer of fluoropolymer-based solids (similar to Teflon) that is bonded to the glass.

Replacement equipment that Apple provides as part of the repair or replacement service may contain new or previously used genuine Apple parts that have been tested and pass Apple functional requirements.

I ordered a replacement screen from China on eBay. I followed this write-up to disassemble the screen unit from the car, then disassembled the electronics from the screen (no biggie) plugged the FRESH new screen into the circuit board, replaced the metal protector and connected it back to the plastics, reinstalled it into the car, and voila, totally fresh new screen. Total time. 20 minutes to remove from car and check to make sure it was part number LQ088K9LA02, 2 weeks wait to receive the part from China. Then about 1 hour to remove and replace the screen. Perfect replacement, perfect fit, really pretty easy job.