tft lcd monitor ip installation factory

TFT-LCD MonitorADMNM17LCDADMNM19LCDADMNM17LCDXADMNM19LCDXINSTRUCTION MANUALPlease read this manual thoroughly before use, and keep it handy for future reference.Document Number: 20051220-10BPart Number: V531-LB17T-T01Version: V2.1

WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCTTO RAIN OR MOISTURE.DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.CAUTION:CAUTIONExplanation of Graphical SymbolsThe lightning flash with arrowhead symbol, within an equilateral triangle, isintended to alert the user to the presence of un-insulated "dangerousvoltage" within the product"s enclosure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.PrecautionsThe exclamation point within an equilateral triangle is intended to alert theuser to the presence of important operating and maintenance (servicing)instructions in the literature accompanying the product.• SafetyShould any liquid or solid object fall intothe cabinet, unplug the unit and have itchecked by the qualified personnel beforeoperating it any further.Unplug the unit from the wall outlet if it isnot going to be used for several days ormore. To disconnect the cord, pull it out bythe plug. Never pull the cord itself.Allow adequate air circulation to preventinternal heat build-up. Do not place theunit on surfaces (rugs, blankets, etc.) ornear materials(curtains, draperies) thatmay block the ventilation holes.• InstallationDo not install the unit in an extremely hotor humid place or in a place subject toexcessive dust or mechanical vibration.The unit is not designed to be waterproof.Exposure to rain or water may damagethe unit.• CleaningClean the unit with a slightly damp softcloth.Use a mild household detergent. Neveruse strong solvents such as thinners orbenzene as they might damage the finishof the unit.Retain the original carton and packingmaterials for safe transport of this unit inthe future.2

FCC Compliance StatementInformation to the user: This equipment has been tested and found to complywith the limits for a class B digital device, pursuant to part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception,This can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one on more of the followingmeasures:- Re-orient or relocate the receiving antenna- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.- Consult the dealer or an experienced radio/TV technician for helpCAUTION: Changes or modifications not expressly approved by the partyresponsible for compliance could void the user"s authority to operate theequipment.This product complies with other various regional and safety regulations such asFCC, CE. These certifications are noted on the product label.3

Important Safeguards1. READ INSTRUCTIONS -- All the safetyand operating instructions should beread before the appliance is operated.2. RETAIN INSTRUCTIONS -- The safetyand operating instructions should beretained for future reference.3. CLEANING -- Unplug video monitor orequipment from the wall outlet beforecleaning. Do not use liquid cleaners oraerosol cleaners. Use a damp cloth forcleaning.4. ATTACHMENTS -- Do not useattachments not recommended by thevideo monitor or equipment manufactureras they may result in the risk of fire,electric shock or injury to persons.5. WATER AND MOISTURE -- Do not usevideo monitor or equipment near water --for example, near a bathtub, washbowl,kitchen sink, laundry tub, in a wetbasement, or near a swimming pool, orthe like.6. ACCESSORIES -- Do not place videomonitor or equipment on an unstablecart, stand or table. The video monitor orequipment may fall, causing seriousinjury to a child or adult, and seriousdamage to the equipment. Wall or shelfmounting should follow themanufacturer"s instructions, and shoulduse a mounting kit approved by themanufacturer.7. Video monitor or equipment and cartcombinations should be moved withcare. Quick stops, excessive force, anduneven surfaces may cause theequipment and cart combination tooverturn.8. VENTILATION -- Slots and openings inthe cabinet and the back or bottom areprovided for ventilation, and to ensurereliable operation of the video monitor orequipment and to protect it fromoverheating. These openings must notbe blocked or covered. The openingsshould never be blocked by placing thevideo monitor or equipment on a bed,sofa, rug, or other similar surface. Videomonitor or equipment should never beplaced near or over a radiator or heatregister. Video monitor or equipmentreceiver should not be placed in a built-ininstallation such as a bookcase unlessproper ventilation is provided.9. POWER SOURCES -- Video monitor orequipment should be operated only fromthe type of power source indicated onthe marking label. If you are not sure ofthe type of power supplied to your home,consult your video monitor or equipmentdealer or local power company. For videomonitor or equipment designed tooperate from battery power refer to theoperating instructions.10. GROUNDING OR POLARIZATION --This video monitor may be equipped witha polarized alternating - current line plug(a plug having one blade wider than theother). This plug will fit into the poweroutlet only one way. This is a safetyfeature. If you are unable to insert theplug fully into the outlet, try reversing theplug. If the plug should still fail to fit,contact your electrician to replace yourobsolete outlet. Do not defeat the safetypurpose of the polarized plug.11. Alternate Warnings - This video monitoris equipped with a three-wiregrounding-type plug, a plug having athird (grounding) pin. This plug will onlyfit into a grounding-type power outlet.This is a safety feature. If you are unableto insert the plug into the outlet, contactyour electrician to replace your obsoleteoutlet. Do not defeat the safety purposeof the grounding-type plug.12. POWER CORDS -- Do not allowanything to rest on the power cord. Donot locate video monitor or equipmentwhere the cord will be abused bypersons walking on it.13. HEED WARNINGS -- Follow allinstructions marked on the video monitoror equipment.14. LIGHTNING -- For added protection forvideo monitor or equipment during alightning storm, or when it is leftunattended and unused for long periodsof time, unplug it from the wall outlet anddisconnect the antenna or cable system.This will prevent damage to the videoproduct due to lightning and power-linesurges.15. OVERLOADING --Do not overload walloutlets and extension cords as this canresult in a risk of fire or electric shock.4

Important Safeguards16. OBJECT AND LIQUID ENTRY -- Neverpush objects of any kind into videomonitor or equipment through openingsas they may touch dangerous voltagepoints or short-out parts that could resultin a fire or electric shock. Never spillliquid of any kind on the product.17. SERVICING -- Do not attempt to servicevideo monitor or equipment yourself asopening or removing covers may exposeyou to dangerous voltage or otherhazards. Refer all servicing to qualifiedservice personnel.19. SAFETY CHECK -- Upon completion ofany service or repairs to this videoproduct, ask the service technician toperform safety checks to determine thatthe video product is in proper operatingcondition.20. FIELD INSTALLATION -- This installationshould be made by a qualified serviceperson and should conform to all localcodes.18. DAMAGE REQUIRING SERVICE --Unplug video monitor or equipment fromthe wall outlet and refer servicing toqualified service personnel under thefollowing conditions:A. When the power-supply cordor the plug has beendamaged.B. If liquid has spilled, or objectshave fallen into the videoproduct.C. If the video product has beenexposed to rain or water.D. If the video product does notoperate normally by followingthe operating instructions,adjust only those controlsthat are covered by theoperating instructions as animproper adjustment of othercontrols may result indamage and will oftenrequire extensive work by aqualified technician to restorethe video product to itsnormal operation.E. If the video product has beendropped, or the cabinetdamaged.F. When the video productexhibits a distinct change inperformance -- this indicatesa need for service.5

Installation GuideAccessoryAll of accessories have been tested and qualified.Do not use any non-qualified accessories with this LCD monitor.Please check all accessories before installation LCD monitor.TFT-LCD monitor x 1USA AC power cord x 1European AC power x 1for ADMNM17LCD and ADMNM19LCD Model OnlyVGA cable x 1User manual x 1European AC power cord x 1UK AC power cord x 1for ADMNM17LCDX and ADMNM19LCDX Model OnlyCD containingmulti languageinstructions x 1Instruction Reading GuideForbid label:Warning that failure to observe couldresult in damage while operating orinstalling the monitor incorrectly.Danger label:To draw installers attention that ifcaution is not observed potentialinjury to the installer or otherpersons could occur.Attention label:The user should pay attention tothe explanation in the manual forthis item while configuring themonitor.Doubt label:A warning that the installers mayneed to consult with others for moredetails on option before proceeding.Suggestion label:The user may like to consider thisfor an optimal setting.6

Contents• Warning ……………………………………………………2• FCC Compliance Statement ……………………………………3• Important Safeguards …………………………………………4• Installation Guide ………………………………………………6• Contents ……………………………………………………7• Quick installation ………………………………………………8• Features ……………………………………………………9• Resolution Support …………………………………………10• Operating Instructions Controls ……………………………………11• Backside Connections …………………………………………12• OSD Architecture ………………………………………………13A. OSD Tree ………………………………………………13B. General Setup ………………………………………………14C. Advanced General Setup ……………………………………15D. CVBS / S-Video Setup …………………………………………16E. CVBS / S-Video Advanced Setup ………………………………17F. VGA Setup ………………………………………………18G. VGA Advanced Setup …………………………………………19H. Audio Setup ………………………………………………20I. PIP Setup ………………………………………………21J. RS-485 Setup ………………………………………………22• Mounting Guide ………………………………………………23A. Desktop ………………………………………………23B. VESA Bracket ………………………………………………24C. Rack Mount Bracket …………………………………………25• Typical Device Connections ………………………………………26• Specification ………………………………………………27• Appendixes ………………………………………………28• Dimensions……………………………………………………30- 7 -

Quick InstallationFor instructions on wall mounting or rack mounting, see page 23 of this user guide.1 Connect power cord2 Connect video cable• Make sure both the LCD display and computer are turned OFF• Connect the video cable from the LCD display to the computer.3 Turn ON LCD display and computer• Turn ON the LCD display, then turn ON the computer. This sequence (LCDdisplay before computer) is important.4 Windows users: Set the timing mode (resolution and refresh rate)Example: 1280 x 1024 @ 60 Hz.For instructions on changing the resolution and refresh rate, see the graphiccard’s user guideInstallation is complete. Enjoy your new LCD display.- 8 -

Features• General• 1280 x RGB x 1024 TFT LCD Panel.• Advance control OSD menu.• High contrast and brightness• PC• 1 analog RGB signal input.• Compatible with SXGA (1280 x 1024) resolution.• Support vertical refresh rate up to 75 Hz for VESA standard specification.• Automatic detection or manual configuration of optimal refresh andsynchronization rates for VGA and composite signals.• VGA screen horizontal / vertical position and width adjustment.• VIDEO• 2 composite (CVBS) signal input.• 2 composite (CVBS) signal loop-out.• Video loop-out auto termination (75 Ohms).• 1 Y/C (S-Video) separate signal input.• Video input support NTSC / PAL / SECAM video standards.• High precision Y/C separation 3D comb filter for NTSC / PAL signal.• 3D concurrent noise reduction.• Time base correction (TBC).• Chroma transient improvement(CTI)• Built-in high quality 3D de-interlace for NTSC / PAL signal.• 9300K / 6500K / User custom color temperatures.• Provide PIP (Picture In Picture) function.• Provide VOV (Video On Video) function.• Support 3:2 and 2:2 pull-down for film source.• AGC (Auto Gain Control) function for all video signals.• Video screen horizontal / vertical position and width adjustment.• Provide over / under / full scan function.• AUDIO• 2x stereo audio input by RCA Jack.• 2W+2W speaker.• Auto audio mute during video loss.• Balance, Bass and Treble audio controls.• Other• Key-lock function.• Programmable power on option.• Signal auto searching.• Power latching.• Power failure auto recover.• Programmable sleep mode for screen.• Easily selectable video switching function.• Multi language (English, German, French, Spain, Japan, Chinese),• RS-485 interface for remote control.• ISP functions for upgrade firmware.• Support VESA 75 x 75 and VESA 100 x 100 mounting standard.• Support Desktop bracket.• Support Rack mount bracket (optional).• Wide voltage range AC 100~240V / 50/60Hz input.• Power consumption 40W@110VAC/60Hz.- 9 -

Resolution Support• VGA resolution tableResolution Symbol H Freq. V Freq. Pixel Remark640 x 480 640-60 31.469 59.941 25.175 VESA640 x 480 640-72 37.861 72.810 31.500 VESA640 x 480 640-75 37.500 75.000 31.500 VESA800 x 600 800-56 35.156 56.250 36.000 VESA800 x 600 800-60 37.879 60.317 40.000 VESA800 x 600 800-72 48.077 72.188 50.000 VESA800 x 600 800-75 46.875 75.000 49.500 VESA1024 x 768 1024-60 48.363 60.004 65.000 VESA1024 x 768 1024-70 56.476 70.069 75.000 VESA1024 x 768 1024-75 60.023 75.029 78.750 VESA1280 x 1024 1280-60 63.981 60.020 108.000 VESA1280 x 1024 1280-75 79.976 75.024 135.000 VESAPlease refer to page 18 for information on automatic input sync optimization.Please note, selecting frequencies outside these ranges may result in anabnormal image or damage to the monitor- 10 -

Operating Instructions - ControlsPowerMonitor ON /OFF. If switched OFF with this button, monitor will be instandby state.Light indicate:Green – Power OnYellow – Standby mode.Red – Power OffAdjust UP / PIPOSD Menu mode - select item above.Normal operating mode - Turn PIP ON/OFF, select PIP source.Adjust Down / Scan ModeOSD Menu mode - select item below.Normal operating mode - Select input sequence.Adjust RIGHT / Volume UpOSD Menu mode - select item to the rightNormal operating mode - Increase Volume level.Adjust LEFT / Volume DownOSD Menu mode - select item to the left.Normal operating mode - Decrease volume level.MENUOSD menu ON or ENTER control.EXIT / AutoOSD Menu mode - exit to previous menu. Exit top menu.Normal operating mode - Force auto sync rate adjustment for VGA input.INPUTSelect input from CVBS1, CVBS2, S-Video, VGA.- 11 -

ConnectionsAUDIO1○1○2○3○4○5○6○7○8○9○10○11PC-AUDIO: Audio signal input for VGA channel.AUDIO 1: Audio signal input 1 for CVBS1 andS-Video. Normally, RED is for right channel;WHITE is for left channel.AUDIO 2: Audio signal input 1 for CVBS2.Normally, RED is for right channel; WHITE is forleft channel.S-VIDEO: Video signal input for Y/C separatesignal.CVBS2 OUT: Video auto termination loop-outfor CVBS2 IN signal. Auto terminationimpedance are 75 Ohms.CVBS 2 IN: composite video signal input forCVBS2 channel.CVBS1 OUT: Video auto termination loop-outfor CVBS1 IN signal. Auto terminationimpedance are 75 Ohms.CVBS1 IN: composite video signal input forCVBS1 channel.RS-485: RS-485 remote control twisted pairinput.VGA: Analog RGB signal input for VGA.AC IN: 100~240VAC power input.Incorrect signal level or frequency may cause damageto the monitor or injure the user.- 12 -

OSD ArchitectureGeneral Setup• Input auto search: Allows monitor to search for an input signal at power on.This function is only available once when the monitor is first turnedON.• Power on default: Set the signal input priority at power ON.CVBS1: Set channel to AV1 when power is turned ON.CVBS2: Set channel to AV2 when power is turned ON.S-Video: Set channel to S-Video when power is turned ON.VGA: Set channel to VGA when power is turned ON.None: No changing.• Auto power on: Allows the monitor to memorize the power status prior to powerfailure and resume the same status on restoration of power.ON: Set ON to enable the function.OFF: Set OFF to disable the function.Suggest set Auto power on to “ON”.• Language: Allows user to select the OSD menu Languages in English, German,French, Spanish, Italian.• Key lock: This function is from preventing an unauthorized person to accessingthe OSD settings.ON: Key-lock function enabled.OFF: Key-lock function disabled.If key-lock function is enabled, the monitor will auto lock its keypad 1 minuteafter the last key press.To unlock the keypad, press and hold the menu button for 5 seconds.• Back light: Allows user to adjust panel backlight level.• Factory reset: Reset the monitor to the original factory settings.- 14 -

OSD ArchitectureGeneral Advanced Setup• V-loss setup: Places monitor into sleep mode after video loss. Delay period isdefined by slide bar.When the slide bar is set to 0, video loss sleep is disabledand its status is shown as below:• OSD Position: This feature allows user configuration of OSD menu position onscreen.Area1: OSD menu on top-left.Area 1 Area 4Area2: OSD menu on bottom-left.Area3: OSD menu on screen centerArea 3Area4: OSD menu on top-right.Area 2 Area 5Area5: OSD menu on bottom-right.• Logo Display: This feature allows user turn on/off company logo at power on.ON: Show company logo at power on.OFF: Hide company logo.• Display: Show / Hide channel title.ON: Show channel titleOFF: Hide channel title- 15 -

OSD ArchitectureCVBS / S-Video Setup• Brightness: Adjusts the overall picture shade and brightness.• Contrast: Permits adjustment for contrast between light or dark areas of thepicture.• Color: Adds color to the black and white picture content (of a color signal), and isusually set for viewer’s preference in color saturation.• Hue: Adjusts the shade of all the colors on the screen, but is most noticeable tothe eye in reds and yellows, and is also usually set for pleasing face tones(NTSC only).• Sharpness: Sets the desired sharpness of the image.• Color temperature: Selects color temperature of 6500°K, 9300°K or User.• Factory reset: Reset the monitor to the original factory settings.- 16 -

OSD ArchitectureCVBS / S-Video Advanced Setup• Scan Mode: This function allows user to select monitor display format.Under: this feature displays the picture with all extremities of thesource image visible (reduced size)Over: this feature displays the picture with all extremities of thesource image hidden (increased size)Full: this feature displays the picture with all extremities of thesource image aligned with the visible area of the screen(full size)• H-position: Adjusts horizontal position of image.• V-position: Adjusts vertical position of image.• Comb filter: Allows the user to manually turn the video comb filter ON/OFF.ON:Enable comb filter.OFF: Disable comb filter.Suggestion set Comb filter to “ON”.- 17 -

OSD ArchitectureVGA Setup• Input sync. auto: This feature allows the user to auto-optimize the displayedpicture under VGA mode.• Brightness: Adjusts the overall picture shade and brightness.• Contrast: Permits adjustment for contrast between light or dark areas of thepicture.• Color temperature: Selects color temperature of 6500°K, 9300°K or User.• Factory reset: Reset the monitor to the original factory settings.- 18 -

OSD ArchitectureAudio Setup• Mute: Select Audio Mute.• Volume: Set audio volume level for internal speakers.• Treble: Adjusts the treble content of the sound from the internal speakers.• Bass: Adjusts the bass content of the sound from the internal speakers.• Balance: Adjusts the audio speakers’ balance.• Factory reset: Reset the monitor to the original factory settings.- 20 -

OSD ArchitecturePIP Setup• Source: This feature allows a user to select the video input signal to be displayedwhen in PIP mode.CVBS1:Turn on the PIP, and set PIP channel source to CVBS1.CVBS2:Turn on the PIP, and set PIP channel source to CVBS2.S-Video:Turn on the PIP, and set PIP channel source to S-Video.OFF:Turn off PIP window.• Swap: swaps the main screen image with the content of the PIP.• Bezel size: Adjusts the thickness of the PIP window border.• Size: Adjusts the overall size of the PIP window.• H-Position: Adjusts the horizontal position of the PIP window.• V-Position: Adjusts the vertical position of the PIP window.- 21 -

Installation GuideDesktop1 With the monitor on a flat surface, hold the base at one side with one hand anddraw the screen upwards with the other hand, until the required tilt angle isachieved.Click!A noticeable "click" will be heard, and felt, asthe screen is moved into the normal range oftilt.(For detailed range, see image below)Do not touch the display area ofthe screen with hands, fingers or anysharp object, or use tools to raise thescreen, otherwise damage to thescreen may occur.Do not place fingers into the hingearea, otherwise injury may occur whenraising the screen.Only attempt to raise the screen ona flat, level and stable surface, such asa tabletop.If you have any support questionsrelating to this operation, please contactTyco Technical Support, who will bepleased to assist you.2 When using the desk stand, only operate the panel on a flat surface, which isno more than 10 degrees from level.3 Optimum viewing angles are obtained when viewing the monitor when it is setbetween +20º and -5º from vertical.Adjust the tilt angle for optimum image quality.- 23 -

Installation GuideVESA Bracket1 Holding the front of the base with one hand, use the other hand to push the topof the casing back, until it lies flat.Do not insert fingers onto the hingearea, otherwise injury may occur whenfolding down the screen.The screen should only be foldeddown of a flat, stable, level surface.2 Lay the LCD display face down on a towel or blanket. Note the 4 screws thatsecure the hinge on the lower part of the back casing. These may be removedto release the desk mount bracket if required.3 Attach a VESA compatible mounting bracket to theappropriate set of holes (both 75mm x 75mm and100mm x 100mm are supported)Use only M4 x 12mm screws to mount the VESA bracket, failure toobserve this may cause serious injury.Ensure that the VESA bracket has an adequate size mounting plate,screws and or fixings to support the weight of the monitor and bracketto the surface to which it is being attached.Failure to observe this may cause serious injury.If there is any doubt of the suitability of a mount or fixing method, aqualified technician should be consulted.- 24 -

Installation GuideOptional Accessory ADMNRKT17 or ADMNRKT191 Remove the desk mount bracket as detailed in the previous section.2 Fix the rack mount brackets to the two sides of the monitor as shown below.Use the supplied M3 screws to mount the monitorto the brackets. Failure to observe this may result inserious injury.3 Fix the monitor in rack.Use screws applicable to the rack system in use.Failure to observe this may result in serious injury.If there is any doubt of the suitability of a mount orfixing method, a qualified technician should beconsulted.- 25 -

Specification17" 19”Pixel Type Normal white Normal blackMax. Resolution 1280 x RGB x 1024 1280 x RGB x 1024Aspect Ratio 4:3 4:3640 x 480 @ 60/72/75Hz 640 x 480 @ 60/72/75 Hz800 x 600 @ 56/60/72/75 Hz 800 x 600 @ 56/60/72/75 HzResolution / Scan for VGA / DVI1024 x 768 @ 60/70/75 Hz 1024 x 768 @ 60/70/75 Hz1280 x 1024 @ 60 / 75 Hz 1280 x 1024 @ 60 / 75 HzViewing Area 337.920(H) x 270.336(V) 376.32(H) x 301.056(V)Pixel Pitch 0.264 x 0.264 mm 0.294 x 0.294 mmBrightness 420 cd/m2 450 cd/m2Contrast Ratio 500:1 450:1Backlight TypeType 4CCFL 4CCFLHours 50,000 hr(Typ) 50,000 hr(Typ)Viewing Angle (H/V) 160/160 140/135Display Color 16.2M colors 16.2M colorsResponse Time 8ms(tr+tf) 12ms(tr+tf)Sync. FormatNTSC / PAL / SECAMFrequency (Horizontal)PC: 31.5K~80KHz Video 15750 / 15625Hz (NTSC/PAL/SECAM)Frequency (Vertical)PC: 56Hz~75Hz Video: 50 / 60HzD-Sub 15 In x 1, Video In x 2 (BNC), Video Out x 2 (BNC), S-Video In x 1VGA Yes, x 1Video InterfaceCVBS Yes, x 2Input InterfacesS-Video Yes, x 1Audio Interface Audio In x 2, PC Phone In x 1Input Power AC Socket In x 1Input SignalComposite signal 0.5~2Vpp / 75ohm (Auto Termination), Y Signal 1Vpp, Csignal 0.3 VppIntegrated Speakers Yes (2W + 2W)Front Panel ControlsPower, Adjust Up/Down/Left/Right, Menu, Exit, InputIndicatorsLED, Power on, Stand by, SleepRemote ControlNoPIP & VOVVOV + PIPComb Filter3D (NTSC / PAL)De-interlace3D (NTSC / PAL)Noise reduction3DTBSYesCTIYesAGCYes3:2 2:2 pull-down YesNon-linear scalingNoPower Failure Auto RecoverYesSpecial FeaturesColor Temperature9300 ゚ K / 6500 ゚ K / UserScan ModeOver / Full / UnderKey LockYesRack mount TypeYesPower LatchingYesPower on OptionCVBS1 / CVBS2 / S Video / VGAAuto signal searchingYesRS-485YesPVM expandNoCDS light sensorNoISP functionYesExpand interfaceNoLanguageEnglish, German, French, Spain, Japan, ChineseRack Tilt Angle / Swivel up 15° / down 15°VESA Mounting VESA 75 / VESA 100Power TypeAC 100~240 VAC 50/60HzPower SupplyInternalTemp (Oper.)0 ゚ C ~ 35 ゚ CMax. Temp50 ゚ CTemp (Storage)-10 ゚ C ~ 60 ゚ CDimension 387.5 x 424.9 x 92.48 mm 425 x 440.2 x 92.48 mm- 27 -

AppendixesCheck the information in this section to see if the problems can be solved before requestingrepair:The consumers are only allowed to solve the problems described as below.Any unauthorized product modification, or failure to follow instructions supplied with theproduct will void the warranty immediately.Problem: No Power indication Make sure power cord is correctly. Make sure power voltage range is between 100~240Vac.Problem: No image Make sure power button is ON. Check whether the LCD monitor and computer or video devices power cords areplugged in and that there is a supply of power.Problem: No signal Check the signal connection between the computer and LCD monitor. Make sure the computer power is ON. Make sure the correct input is selected.Problem: “Out of Range” Check the computer image output resolution and frequency and compare thevalue with preset value (please refer to page 10).Problem: Fuzzy image Adjust “Input sync. manual” in VGA advance setup.Problem: Image too bright or Image too dark Adjust brightness and contrast by OSD.Problem: Irregular image Check the signal connection between the computer and LCD monitor. Perform “Input sync. auto”.Problem: Distorted image Reset LCD monitor. (perform the “Factory Reset” function by OSD)Problem: Image is not centered Size is not appropriate Take off extra accessories. (such as looped out video signal) Use OSD image menu to adjust H-Position and V-Position. Check image size setting. Perform “Input sync. auto”.- 28 -

AppendixesProblem: Uneven color or Color too dark or Dark area distorted Use OSD “Color” function to adjust color setting.Problem: White color is not white Check “Color temperature” is correct. Use OSD “Color” function to adjust color setting. Use OSD “Hue” function to adjust color setting.Problem: Can not adjust LCD monitor with buttons in the front. Check OSD “Key lock” function is ON.Problem: All of image can not be seen on the screen Use OSD “Scan mode” function to adjust screen size.- 29 -

ORION Images IP camera tester was developed for on-site installation and maintenance of IP or Analog cameras. Features include a 7" video display, PTZ control, DC12V output power, Audio test, PING testing and IP address scanning. The TMIPHD7 IP tester is designed for easy operation and portability. Simplifies the technicians job of installation and maintenance of CCTV systems. Saves cost by reducing technician time in the field.