printers display screens and speakers are __________ devices made in china

An output device is any hardware component that conveys information to one or more people. Commonly used output devices include display devices; printers, speakers, headphones, and earbuds; data projectors; and interactive whiteboards.

A display devices is an output device that visually conveys text, graphics, and video information. Desktop computers typically use a monitor as their display device. A monitor is a display device that is packaged as a separate peripheral. Some monitors have a tilt-and-swivel base that allows users to adjust the angle of the screen to minimize neck strain and reduce glare from overhead lightning. You can rotate the screen also of the few monitor. Adjustable monitor stands allow you to adjust the height of the monitor. Some have integrated speakers and/ or built-in Web cam. Monitor controls permit users to adjust the brightness, contrast, height, and width of images. Types of display devices include LCD monitors and LCS screens, plasma monitors, and CRT monitors. The following sections discuss each of these display devices.

An LCD monitors is a desktop monitor that uses a liquid crystal display to produce images. These monitors produce sharp, flicker-free images. LCD monitors have a small footprint; that is they do not take up much desk space. LCD monitors are available in a variety of sizes, with the more common being 19, 20, 22, 24, 26, 27, and 30 inches some are 45 or 65 inches

A liquid crystal display (LCD) uses a liquid compound to present information on a display device. Computer LCD typically contain fluorescent tubes that emit light waves towards the liquid-crystal cells, which are sandwiched between two sheets of material. The quality of an LCD monitor or LCD screen depends primarily on its resolution, response time, brightness, dot pitch and contrast ratio.

A Plasma monitor is a display device that uses gas plasma technology, which sandwiches a layer of gas between two glass plates. Plasma monitors offer screen sizes up to 150 inches wide and richer colors than LCD monitors but are more expensive. Like LCD monitors, plasma monitors can hang directly on a wall.

A CRT monitor is a desktop monitor that contains a cathode-ray-tube. A cathode ray-tube (CRT) is a large, sealed glass tube. The front of the tube is the screen. A CRT’s viewable size is the diagonal measurement of the actual viewing area provided by the screen in the CRT monitor. A 21 inch monitor, for example, many have a viewable size of 20 inches. CRT monitors produce a small amount of electromagnetic radiation. Electromagnetic radiation (EMR) is a magnetic field that travels at the speed of light. Excessive amounts of EMR can pose a health risk.

A printer is an output device that produces text and graphics on a physical medium such as paper. Many different types and styles of printers exist with varying speeds, capabilities, and printing methods.

A nonimpact printer forms characters and graphics on a piece of paper without actually striking the paper. Some nonimpact printers spray ink, while others use heat or pressure to create images. Commonly used nonimpact printers are ink-jet printers, photo printers, laser, thermal printers, mobile printers etc.

An ink-jet printer is a type of nonimpact printer that forms character and graphics by spraying tiny drops of liquid ink onto a piece of paper. Ink-jet printers have become a popular type of color printer for use in the home. Ink-jet printers produce text and graphics in both black and white and color on a variety of paper types. The print head mechanism in an ink-jet printer contains ink-filled cartridges. Each cartridges has fifty to several hundred small ink holes. or nozzles.

An audio output device is a component of a computer that produces music, speech, or other sounds, such as beeps. Three computers used audio output devices are speaker, headphones. Most personal computers and mobile devices have a small internal speaker that usually emits only low-quality sound. Thus, many users attach surround sound speakers or speaker system to their computers to generate higher-quality sounds. Speakers typically have tone and volume controls, allowing users to adjust setting. In many cases, a cable connects the speakers or the subwoofer to a port on the sound card.

A data projector is a device that takes the text and images displaying on a computer screen and projects them on a larger screen so that an audience can see the image clearly. Some data projectors are large devices that attach to a ceiling or wall in an auditorium. Other, designed for the mobile user, are small portable devices that can be transported easily.

The printing technology that allows for faster and cleaner printing helps companies meet their printing needs efficiently while enhancing the overall worth o...

When the ink layer on paper is too thin, it is caused by less printing pressure and less amount of ink is transferred. The central position of plate cylinder...

This paper will identify and explain technology by making specific references to some common technologies. Then I will give an overview of their use and impo...

Their latex inks boast similar features and environmental advantages to HP inks. They also have the additional benefit of white ink to the traditional four c...

You can find basic printers that print word documents, webpages, excels sheets or emails in monochrome or colour for your day to day needs. For the bigger of...

You know, none of these are really easy choices. If it"s just you working on the system, the decisions might be simple, but if you have to consider others" opinions, not so much. Let"s start with the monitor. We use this to view the work we"re doing at the time or to view a finished product. We may also use it to view videos or photos we"ve taken or found online.

Monitors come in many sizes and descriptions. To make the best decision, you should ask yourself what you"ll be doing the most with your computer. Are you just writing papers or creating presentations? Are you surfing the Internet? Are you playing games once in a while? Are they games that are not intensive in graphics? Are you making and editing videos for fun - or for a profession?

If you can keep it simple, the standard monitor is for you. If you"re playing games with intensive graphics, making videos or working with digital photographs or art, you may want a high-definition monitor. If you"re going to use a computer as your home entertainment system, you can find one that is TV-ready as well.

The size of the monitor you use truly depends on your preference. Things to consider are your eyesight, who else will be using it and the distance the monitor will be sitting away from you (assuming you go with a desktop unit, not a laptop). There are monitor sizes ranging from 7 inches as a supplementary peripheral, but normal monitors range from a 17-inch diagonal to a monster 55-inch diagonal! You could comfortably surf from the couch in the living room with a monitor this size.

Monitors are created with LCD (liquid crystal display) or LED (light-emitting diode). LCDs have layers of glass, polarized film and liquid crystals. You get electrical impulses sent through, and this causes the color to be shown and image to be displayed. LED monitors take the LCD one step further. They put a diode on the back that forces light through the layers for a sharper picture and better colors. It is said that LED monitors will last longer than LCD monitors.

Have you decided which one you want to go with? Don"t forget, you"ve also got touchscreen monitors available should you have a use for them. The most practical use of a touchscreen monitor for consumer and professional use would be to someone with a physical disability.

The next difficult decision to make will be the printer that will work best for you. Printers are used to create a tangible product to look at away from a monitor. For consumer use there are two kinds to choose from: the inkjet and the laser printer.

The inkjet printer uses a liquid ink that"s sprayed through a print head onto a piece of paper. How? Simply put, the printer interprets the signal from the computer and converts it to instructions that go through the print head. Inkjet printers are typically inexpensive to purchase, although the replacement ink can be costly and add up.

Laser printers use heat technology and specialized powder called toner or another medium (I"ve seen it with wax - it looked like crayons) that"s heat-sealed onto a piece of paper. Laser printers are somewhat expensive, though they"ve come down in cost as the technology has increased.

Both types are often available as mono-color (or black-only printer), full-color or an all-in-one printer. An all-in-one printer typically has a printer, a copier and a scanner. Some still have a fax feature as well.

You should ask yourself how much you"ll be printing and how often. If you don"t print too much, the inkjet printer may be for you. One disadvantage, though, to not printing often with an inkjet printer is that the print head can actually plug up, dry out and then not work. If you print frequently or in large quantities, you may find yourself purchasing ink quite often. Ink varies in price but ranges between $9 and $25 for about 250 sheets of text-only in black ink. The toner for laser printers seems prohibitive but usually will print up to 5000 sheets of paper per cartridge. These toners are between $80-$100 a unit.

An example of typical usage: several years ago I bought a mono-laser printer (actually, it was an all-in-one) for about $170. It was used to create syllabi for seven different classes and hand-outs for most of those classes, for my daughter to write papers for her high school classes and for my son (who discovered SpongeBob on the Internet and printed out hundreds of coloring sheets), and I prepared at least 60 tax returns in that season. The one toner cartridge lasted more than a year.

Speakers are used to emit audio signals that may come from music files or other audio files. Many pre-constructed computers come with external speakers. All come with internal speakers. Usually, the external speakers included are more than good enough for sound quality, whether you"re watching YouTube videos or playing a movie in your DVD player. There are people who prefer a little more bump in their audio output, however. Speakers are available in surround-sound systems that rival a home system. How loud you want your system to be is up to you. The higher-quality the sound system, the more expensive it will be.

Many computers now support Bluetooth technology. You can connect to Bluetooth-enabled speakers and set them up without the need for additional cables or connections!

You don"t have to pick all of these output devices for your computer system, but it is important to remember that monitors are output devices that let us see what we"re working on as we are working on it as well as to get a feel for what the finished product looks like.

Speakers are fun to shop for. They"re an audio output device allowing the transmission of sound files so the user can hear them. You can pick out how loud you want your system to be and find the sound package that works for you.

The computer will then display or reproduce that information via one or more output devices. It’s therefore essential for computer users to differentiate between input and output devices.

The vast majority of devices can be labelled as input or output since they will either receive information from the user or transmit it. You may also come across devices known as I/O devices that are capable of both taking input and showing output at the same time.

To put it simply, a mouse is a pointing device. This means that users can control the pointer on a computer display by using it. The touchpad on a laptop computer serves the same purpose as a mouse.

A keyboard is one of the most important input devices. You can use it to input data into a computer or other electronic devices. They do this by connecting to the computer in one of two ways: wirelessly or through a USB system.

Letters A through Z and numbers 0 through 9 make up the keyboard. There are 17 digits on the numeric keypad, enabling a wide range of arithmetic operations. The top row of the keyboard also usually contains the computer"s function keys. Furthermore, users can easily navigate the page and make selections using useful control keys like tab, enter, shift, etc.

While regions use different keyboard layouts, the worldwide standard for keyboards is the QWERTY keyboard. The term "qwerty" comes from the first six letter keys on the keyboard.

It is a device that transfers the acoustic energy from an audible source into an electric signal for playback through an amplification system. Therefore, professions such as voice actors and filmmakers have benefited greatly from this technology. The mic’s primary advantages lie in its small size, low price, and high response sensitivity.

These days, microphones can also function as voice recognition devices. Furthermore, we can now use the “Speech Input Device” feature to dictate our text instead of typing it.

In many scenarios, using a joystick provides far more intuitive control than a mouse. Thus, it is useful in a wide variety of situations, including when playing video games, training simulations, steering helicopters, and many more!

The trackball is an alternative computer input device that functions similarly to a mouse. It looks like a ball and has a few buttons on top. A normal handling position involves your thumb being on the ball and the other fingers on its buttons.

The Scroll is an outside roller that you may rotate to smoothly move the displays. When pushed, the Scroll also serves as a button to prevent the screens from stopping.

A trackball is a track-sphere. Therefore, it has a feature found in certain wireless mouse models that allow for the rotation of the screen in any direction, not just up and down. This is very useful for games and other graphic design software.

Trackballs quickly gained popularity in portable computing devices because of their small size, making them easy to carry and store. Moreover, many users prefer trackballs since they"re thought to be more reliable than a mouse.

A speaker is an audio output hardware component that is often linked to a computer. It works similarly to sound cards, which are a kind of hardware usually included within a computer and responsible for creating the audible output from the system"s speakers.

The sound card processes the audio input and outputs sound via the computer"sspeaker. These days you will find a built-in speaker on almost all laptops near the top of your keyboard.

Printers create a physical duplicate of digital information. Since the printer"s primary function is to transform digital information into paper, they are essential to every digital environment.

Files, images, and other digital metadata are saved on a computer and can be printed using aprinter. Offices, residences, PowerPoint presentations, and businesses all utilise printers to print signs and other materials.

The size of the printed output depends on the paper size you use. On the other hand, the DPI density of a printer is a measure of the quality of the printed picture. The higher the printer"s DPI, the sharper and more detailed the output.

In most cases, you will need a communication cable or a wireless network to link the printer to the computer. However, many modern digital printers have other connection alternatives, such as Wi-Fi or cloud. This makes it simpler and quicker to complete a printing job.

Examining documents, images, videos, graphics, and tables in their original format and in real-time is possible on the screen.LED, LCDand plasma are just a few examples of cutting-edge monitor technologies.

You can listen to your device’s audio privately by pluggingheadphonesinto the output jack. Otherwise, you can also use and connect this type of device via a wireless connection to a mobile device or PC.

People most commonly use headphones or earbuds in public settings when they want to listen to audio without bothering others around them. The sound card (or any other connected device) provides audio input, and then the headphones transform that signal into wave sound for output.

A multimedia projector is also an output device. Having access to a multifunctional projector is not unlike having a magic wand because it can do so much quickly and easily.

Whether for presentations, data visualisations, or documentary screenings, a projector is versatile and allows for a complete video broadcast. Hence, using a projector improves the audience"s ability to absorb and process the presented material.

A headset combines an output device (the speaker) and an input device (the microphone). Headsets are a necessary and useful tool for anyone who has to communicate or listen to audio in a shared space. TheHyperX Cloud Alpha S Gaming Headsetis perfect for everyday use thanks to its comfortable design. It also has bass adjustment sliders to personalise your sound.

Compact Disc (CD) and DVD (DVD) Drives store information from computers in the specified format. They can then transfer this data to other devices by taking up disk space.

There are numerous input and output devices that you can connect to your computer. Input and output devices play key roles and are very useful for computers. Understanding the differences between these two devices is very important if you want to maximise performance.

Ray Bradbury is a renowned author famous for his short science fiction stories and his novel "Fahrenheit 421". His works have inspired many and raised numerous questions about what the future may hold. He"s quoted as saying "I don"t try to describe the future. I try to prevent it." (Bradbury), and in many ways you can see the motif of this mindset in his work. He goes into detail about the dangers of reliance on technology, the ways it could result in our downfall as societies and people. He passed away in 2012 yet his stories live on and remain significant, not only as relics in history, but as reminders of what we"ve become and what we may be moving toward if we"re not careful. In today"s world its hard to go too far without seeing somebody wrapped up in something as simple as a

Gutenberg took the Chinese technique of block printing, rag paper, oil based inks, a screw press that was typically used to produce wine and olive oil, and made movable type letters of metal to create his printing press. The screw press was specially designed to achieve an effective and even transfer of the image to paper or even

As an IT technician, it is need to specify the hardware devices. Thus, it is consists of input devices, out devices and storage devices in order to set up a Multimedia Lab in Computing & Information Technology Department.

The 1950s was the decade that defined America after the second world war. The 50s birthed many of mankind’s greatest technological feats that still shine through today. One of the biggest political and social battles also took place in the decade.

Over 17 million people died in World War I. Over 60 million people died in World War II. The deaths almost tripled because of the advancements in the war. 73 years ago on September 1, 1939 Germany invaded Poland without warning sparking the start of World War II. By the evening of September 3, Britain and France were at war with Germany and within a week, Australia, New Zealand, Canada and South Africa had also joined the war. The world had been plunged into its second world war in 25 years. The technological advancements in World War II affected the wars in the following years because of advancements in weapons, inventions, and improvements in medicine.

A Keyboard allows for you to enter different characters such as letters, numbers and symbols. Each key on a keyboard represents a different character on the computer. There are several different types of keyboards, Ergonomic Keyboards, QWERTY Keyboards, and Braille Keyboards. Another example of an Input Device is a Mouse. A Mouse is a Pointing Device which allows you to move the cursor on the computer.

Computers have one or a lot of big or small R-A-M chips inside. RAM chips are a random access memory chip inside, the computer uses it to store information that will be used anytime or used to store something like the copy clipboard(The copy clipboard is the thing that stores what you copy to paste later) to delete/change later. There is also a spinning or solid state hard drive that uses DVD like disks that stores information like your video games, pictures, or other things. A CPU is the thing that your computer uses to do all the processing work, like our brain but not like it. CPU stands central-processing-unit.

For this particular task, I will be explaining what key components are necessary for client workstations to connect to a network and how to access network resources. I will be explaining the key features and functions of each of these components in relative detail.

These are mechanisms used to connect computers and other electronic devices together so they can exchange and share files or special resources like printers or fax machines used in big organisations. LAN is the main type of network device used by the community.

Imagine a world where communication is difficult, there is not a lot of entertainment, and places are hard to get to. This actually was the world in the 1900s-1910s. Technology has come a long way since the early 1900s. Our world has become more advanced and fast paced due to the advances of technology. Over the last 100 years, technology is by far the biggest change in our culture.

Software resources include all sets of information processing instructions. Software is a general term for the various kinds of programs used to operate computers and related devices.

In second language learning, using visual aids is a necessity teaching strategy in both English as Second Language (ESL) classroom and English as Foreign Language (EFL) classroom (Allen, Kate & Marquez, 2011). They believed that using visual aids in the process of teaching a foreign language can strengthen what learners have learned and increase their interest. In their article, they proposed the positive impact of using visuals and they concluded that teachers should become aware of the strategies in which they can use visual aids and use them purposefully in the classroom to enhance students’ learning.

A broadcast or storage medium is utilizing electronic technology. They may include televisions, radios, the Internet, faxes, CD-ROMs, DVDs, and any other medium that requires power or digital information encoding. The term electronic medium is usually in contrast to a print medium.

Virtually growing up in a computer repair shop, Naomi Bolton has held a passion for as long as she can remember. After earning a diploma through a four year course in graphic design from Cibap College, Bolton launched her own photography business. Her work has been featured on Blinklist, Gameramble and many others.

Glass substrate with ITO electrodes. The shapes of these electrodes will determine the shapes that will appear when the LCD is switched ON. Vertical ridges etched on the surface are smooth.

A liquid-crystal display (LCD) is a flat-panel display or other electronically modulated optical device that uses the light-modulating properties of liquid crystals combined with polarizers. Liquid crystals do not emit light directlybacklight or reflector to produce images in color or monochrome.seven-segment displays, as in a digital clock, are all good examples of devices with these displays. They use the same basic technology, except that arbitrary images are made from a matrix of small pixels, while other displays have larger elements. LCDs can either be normally on (positive) or off (negative), depending on the polarizer arrangement. For example, a character positive LCD with a backlight will have black lettering on a background that is the color of the backlight, and a character negative LCD will have a black background with the letters being of the same color as the backlight. Optical filters are added to white on blue LCDs to give them their characteristic appearance.

LCDs are used in a wide range of applications, including LCD televisions, computer monitors, instrument panels, aircraft cockpit displays, and indoor and outdoor signage. Small LCD screens are common in LCD projectors and portable consumer devices such as digital cameras, watches, digital clocks, calculators, and mobile telephones, including smartphones. LCD screens are also used on consumer electronics products such as DVD players, video game devices and clocks. LCD screens have replaced heavy, bulky cathode-ray tube (CRT) displays in nearly all applications. LCD screens are available in a wider range of screen sizes than CRT and plasma displays, with LCD screens available in sizes ranging from tiny digital watches to very large television receivers. LCDs are slowly being replaced by OLEDs, which can be easily made into different shapes, and have a lower response time, wider color gamut, virtually infinite color contrast and viewing angles, lower weight for a given display size and a slimmer profile (because OLEDs use a single glass or plastic panel whereas LCDs use two glass panels; the thickness of the panels increases with size but the increase is more noticeable on LCDs) and potentially lower power consumption (as the display is only "on" where needed and there is no backlight). OLEDs, however, are more expensive for a given display size due to the very expensive electroluminescent materials or phosphors that they use. Also due to the use of phosphors, OLEDs suffer from screen burn-in and there is currently no way to recycle OLED displays, whereas LCD panels can be recycled, although the technology required to recycle LCDs is not yet widespread. Attempts to maintain the competitiveness of LCDs are quantum dot displays, marketed as SUHD, QLED or Triluminos, which are displays with blue LED backlighting and a Quantum-dot enhancement film (QDEF) that converts part of the blue light into red and green, offering similar performance to an OLED display at a lower price, but the quantum dot layer that gives these displays their characteristics can not yet be recycled.

Since LCD screens do not use phosphors, they rarely suffer image burn-in when a static image is displayed on a screen for a long time, e.g., the table frame for an airline flight schedule on an indoor sign. LCDs are, however, susceptible to image persistence.battery-powered electronic equipment more efficiently than a CRT can be. By 2008, annual sales of televisions with LCD screens exceeded sales of CRT units worldwide, and the CRT became obsolete for most purposes.

Each pixel of an LCD typically consists of a layer of molecules aligned between two transparent electrodes, often made of Indium-Tin oxide (ITO) and two polarizing filters (parallel and perpendicular polarizers), the axes of transmission of which are (in most of the cases) perpendicular to each other. Without the liquid crystal between the polarizing filters, light passing through the first filter would be blocked by the second (crossed) polarizer. Before an electric field is applied, the orientation of the liquid-crystal molecules is determined by the alignment at the surfaces of electrodes. In a twisted nematic (TN) device, the surface alignment directions at the two electrodes are perpendicular to each other, and so the molecules arrange themselves in a helical structure, or twist. This induces the rotation of the polarization of the incident light, and the device appears gray. If the applied voltage is large enough, the liquid crystal molecules in the center of the layer are almost completely untwisted and the polarization of the incident light is not rotated as it passes through the liquid crystal layer. This light will then be mainly polarized perpendicular to the second filter, and thus be blocked and the pixel will appear black. By controlling the voltage applied across the liquid crystal layer in each pixel, light can be allowed to pass through in varying amounts thus constituting different levels of gray.

Most color LCD systems use the same technique, with color filters used to generate red, green, and blue subpixels. The LCD color filters are made with a photolithography process on large glass sheets that are later glued with other glass sheets containing a TFT array, spacers and liquid crystal, creating several color LCDs that are then cut from one another and laminated with polarizer sheets. Red, green, blue and black photoresists (resists) are used. All resists contain a finely ground powdered pigment, with particles being just 40 nanometers across. The black resist is the first to be applied; this will create a black grid (known in the industry as a black matrix) that will separate red, green and blue subpixels from one another, increasing contrast ratios and preventing light from leaking from one subpixel onto other surrounding subpixels.Super-twisted nematic LCD, where the variable twist between tighter-spaced plates causes a varying double refraction birefringence, thus changing the hue.

LCD in a Texas Instruments calculator with top polarizer removed from device and placed on top, such that the top and bottom polarizers are perpendicular. As a result, the colors are inverted.

The optical effect of a TN device in the voltage-on state is far less dependent on variations in the device thickness than that in the voltage-off state. Because of this, TN displays with low information content and no backlighting are usually operated between crossed polarizers such that they appear bright with no voltage (the eye is much more sensitive to variations in the dark state than the bright state). As most of 2010-era LCDs are used in television sets, monitors and smartphones, they have high-resolution matrix arrays of pixels to display arbitrary images using backlighting with a dark background. When no image is displayed, different arrangements are used. For this purpose, TN LCDs are operated between parallel polarizers, whereas IPS LCDs feature crossed polarizers. In many applications IPS LCDs have replaced TN LCDs, particularly in smartphones. Both the liquid crystal material and the alignment layer material contain ionic compounds. If an electric field of one particular polarity is applied for a long period of time, this ionic material is attracted to the surfaces and degrades the device performance. This is avoided either by applying an alternating current or by reversing the polarity of the electric field as the device is addressed (the response of the liquid crystal layer is identical, regardless of the polarity of the applied field).

Displays for a small number of individual digits or fixed symbols (as in digital watches and pocket calculators) can be implemented with independent electrodes for each segment.alphanumeric or variable graphics displays are usually implemented with pixels arranged as a matrix consisting of electrically connected rows on one side of the LC layer and columns on the other side, which makes it possible to address each pixel at the intersections. The general method of matrix addressing consists of sequentially addressing one side of the matrix, for example by selecting the rows one-by-one and applying the picture information on the other side at the columns row-by-row. For details on the various matrix addressing schemes see passive-matrix and active-matrix addressed LCDs.

LCDs, along with OLED displays, are manufactured in cleanrooms borrowing techniques from semiconductor manufacturing and using large sheets of glass whose size has increased over time. Several displays are manufactured at the same time, and then cut from the sheet of glass, also known as the mother glass or LCD glass substrate. The increase in size allows more displays or larger displays to be made, just like with increasing wafer sizes in semiconductor manufacturing. The glass sizes are as follows:

Until Gen 8, manufacturers would not agree on a single mother glass size and as a result, different manufacturers would use slightly different glass sizes for the same generation. Some manufacturers have adopted Gen 8.6 mother glass sheets which are only slightly larger than Gen 8.5, allowing for more 50 and 58 inch LCDs to be made per mother glass, specially 58 inch LCDs, in which case 6 can be produced on a Gen 8.6 mother glass vs only 3 on a Gen 8.5 mother glass, significantly reducing waste.AGC Inc., Corning Inc., and Nippon Electric Glass.

The origins and the complex history of liquid-crystal displays from the perspective of an insider during the early days were described by Joseph A. Castellano in Liquid Gold: The Story of Liquid Crystal Displays and the Creation of an Industry.IEEE History Center.Peter J. Wild, can be found at the Engineering and Technology History Wiki.

In 1888,Friedrich Reinitzer (1858–1927) discovered the liquid crystalline nature of cholesterol extracted from carrots (that is, two melting points and generation of colors) and published his findings at a meeting of the Vienna Chemical Society on May 3, 1888 (F. Reinitzer: Beiträge zur Kenntniss des Cholesterins, Monatshefte für Chemie (Wien) 9, 421–441 (1888)).Otto Lehmann published his work "Flüssige Kristalle" (Liquid Crystals). In 1911, Charles Mauguin first experimented with liquid crystals confined between plates in thin layers.

In 1922, Georges Friedel described the structure and properties of liquid crystals and classified them in three types (nematics, smectics and cholesterics). In 1927, Vsevolod Frederiks devised the electrically switched light valve, called the Fréedericksz transition, the essential effect of all LCD technology. In 1936, the Marconi Wireless Telegraph company patented the first practical application of the technology, "The Liquid Crystal Light Valve". In 1962, the first major English language publication Molecular Structure and Properties of Liquid Crystals was published by Dr. George W. Gray.RCA found that liquid crystals had some interesting electro-optic characteristics and he realized an electro-optical effect by generating stripe-patterns in a thin layer of liquid crystal material by the application of a voltage. This effect is based on an electro-hydrodynamic instability forming what are now called "Williams domains" inside the liquid crystal.

The MOSFET (metal-oxide-semiconductor field-effect transistor) was invented by Mohamed M. Atalla and Dawon Kahng at Bell Labs in 1959, and presented in 1960.Paul K. Weimer at RCA developed the thin-film transistor (TFT) in 1962.

In 1964, George H. Heilmeier, then working at the RCA laboratories on the effect discovered by Williams achieved the switching of colors by field-induced realignment of dichroic dyes in a homeotropically oriented liquid crystal. Practical problems with this new electro-optical effect made Heilmeier continue to work on scattering effects in liquid crystals and finally the achievement of the first operational liquid-crystal display based on what he called the George H. Heilmeier was inducted in the National Inventors Hall of FameIEEE Milestone.

In the late 1960s, pioneering work on liquid crystals was undertaken by the UK"s Royal Radar Establishment at Malvern, England. The team at RRE supported ongoing work by George William Gray and his team at the University of Hull who ultimately discovered the cyanobiphenyl liquid crystals, which had correct stability and temperature properties for application in LCDs.

The idea of a TFT-based liquid-crystal display (LCD) was conceived by Bernard Lechner of RCA Laboratories in 1968.dynamic scattering mode (DSM) LCD that used standard discrete MOSFETs.

On December 4, 1970, the twisted nematic field effect (TN) in liquid crystals was filed for patent by Hoffmann-LaRoche in Switzerland, (Swiss patent No. 532 261) with Wolfgang Helfrich and Martin Schadt (then working for the Central Research Laboratories) listed as inventors.Brown, Boveri & Cie, its joint venture partner at that time, which produced TN displays for wristwatches and other applications during the 1970s for the international markets including the Japanese electronics industry, which soon produced the first digital quartz wristwatches with TN-LCDs and numerous other products. James Fergason, while working with Sardari Arora and Alfred Saupe at Kent State University Liquid Crystal Institute, filed an identical patent in the United States on April 22, 1971.ILIXCO (now LXD Incorporated), produced LCDs based on the TN-effect, which soon superseded the poor-quality DSM types due to improvements of lower operating voltages and lower power consumption. Tetsuro Hama and Izuhiko Nishimura of Seiko received a US patent dated February 1971, for an electronic wristwatch incorporating a TN-LCD.

In 1972, the concept of the active-matrix thin-film transistor (TFT) liquid-crystal display panel was prototyped in the United States by T. Peter Brody"s team at Westinghouse, in Pittsburgh, Pennsylvania.Westinghouse Research Laboratories demonstrated the first thin-film-transistor liquid-crystal display (TFT LCD).high-resolution and high-quality electronic visual display devices use TFT-based active matrix displays.active-matrix liquid-crystal display (AM LCD) in 1974, and then Brody coined the term "active matrix" in 1975.

In 1972 North American Rockwell Microelectronics Corp introduced the use of DSM LCDs for calculators for marketing by Lloyds Electronics Inc, though these required an internal light source for illumination.Sharp Corporation followed with DSM LCDs for pocket-sized calculators in 1973Seiko and its first 6-digit TN-LCD quartz wristwatch, and Casio"s "Casiotron". Color LCDs based on Guest-Host interaction were invented by a team at RCA in 1968.TFT LCDs similar to the prototypes developed by a Westinghouse team in 1972 were patented in 1976 by a team at Sharp consisting of Fumiaki Funada, Masataka Matsuura, and Tomio Wada,

In 1983, researchers at Brown, Boveri & Cie (BBC) Research Center, Switzerland, invented the passive matrix-addressed LCDs. H. Amstutz et al. were listed as inventors in the corresponding patent applications filed in Switzerland on July 7, 1983, and October 28, 1983. Patents were granted in Switzerland CH 665491, Europe EP 0131216,

The first color LCD televisions were developed as handheld televisions in Japan. In 1980, Hattori Seiko"s R&D group began development on color LCD pocket televisions.Seiko Epson released the first LCD television, the Epson TV Watch, a wristwatch equipped with a small active-matrix LCD television.dot matrix TN-LCD in 1983.Citizen Watch,TFT LCD.computer monitors and LCD televisions.3LCD projection technology in the 1980s, and licensed it for use in projectors in 1988.compact, full-color LCD projector.

In 1990, under different titles, inventors conceived electro optical effects as alternatives to twisted nematic field effect LCDs (TN- and STN- LCDs). One approach was to use interdigital electrodes on one glass substrate only to produce an electric field essentially parallel to the glass substrates.Germany by Guenter Baur et al. and patented in various countries.Hitachi work out various practical details of the IPS technology to interconnect the thin-film transistor array as a matrix and to avoid undesirable stray fields in between pixels.

Hitachi also improved the viewing angle dependence further by optimizing the shape of the electrodes (Super IPS). NEC and Hitachi become early manufacturers of active-matrix addressed LCDs based on the IPS technology. This is a milestone for implementing large-screen LCDs having acceptable visual performance for flat-panel computer monitors and television screens. In 1996, Samsung developed the optical patterning technique that enables multi-domain LCD. Multi-domain and In Plane Switching subsequently remain the dominant LCD designs through 2006.South Korea and Taiwan,

In 2007 the image quality of LCD televisions surpassed the image quality of cathode-ray-tube-based (CRT) TVs.LCD TVs were projected to account 50% of the 200 million TVs to be shipped globally in 2006, according to Displaybank.Toshiba announced 2560 × 1600 pixels on a 6.1-inch (155 mm) LCD panel, suitable for use in a tablet computer,transparent and flexible, but they cannot emit light without a backlight like OLED and microLED, which are other technologies that can also be made flexible and transparent.

In 2016, Panasonic developed IPS LCDs with a contrast ratio of 1,000,000:1, rivaling OLEDs. This technology was later put into mass production as dual layer, dual panel or LMCL (Light Modulating Cell Layer) LCDs. The technology uses 2 liquid crystal layers instead of one, and may be used along with a mini-LED backlight and quantum dot sheets.

Since LCDs produce no light of their own, they require external light to produce a visible image.backlight. Active-matrix LCDs are almost always backlit.Transflective LCDs combine the features of a backlit transmissive display and a reflective display.

CCFL: The LCD panel is lit either by two cold cathode fluorescent lamps placed at opposite edges of the display or an array of parallel CCFLs behind larger displays. A diffuser (made of PMMA acrylic plastic, also known as a wave or light guide/guiding plateinverter to convert whatever DC voltage the device uses (usually 5 or 12 V) to ≈1000 V needed to light a CCFL.

EL-WLED: The LCD panel is lit by a row of white LEDs placed at one or more edges of the screen. A light diffuser (light guide plate, LGP) is then used to spread the light evenly across the whole display, similarly to edge-lit CCFL LCD backlights. The diffuser is made out of either PMMA plastic or special glass, PMMA is used in most cases because it is rugged, while special glass is used when the thickness of the LCD is of primary concern, because it doesn"t expand as much when heated or exposed to moisture, which allows LCDs to be just 5mm thick. Quantum dots may be placed on top of the diffuser as a quantum dot enhancement film (QDEF, in which case they need a layer to be protected from heat and humidity) or on the color filter of the LCD, replacing the resists that are normally used.

WLED array: The LCD panel is lit by a full array of white LEDs placed behind a diffuser behind the panel. LCDs that use this implementation will usually have the ability to dim or completely turn off the LEDs in the dark areas of the image being displayed, effectively increasing the contrast ratio of the display. The precision with which this can be done will depend on the number of dimming zones of the display. The more dimming zones, the more precise the dimming, with less obvious blooming artifacts which are visible as dark grey patches surrounded by the unlit areas of the LCD. As of 2012, this design gets most of its use from upscale, larger-screen LCD televisions.

RGB-LED array: Similar to the WLED array, except the panel is lit by a full array of RGB LEDs. While displays lit with white LEDs usually have a poorer color gamut than CCFL lit displays, panels lit with RGB LEDs have very wide color gamuts. This implementation is most popular on professional graphics editing LCDs. As of 2012, LCDs in this category usually cost more than $1000. As of 2016 the cost of this category has drastically reduced and such LCD televisions obtained same price levels as the former 28" (71 cm) CRT based categories.

Monochrome LEDs: such as red, green, yellow or blue LEDs are used in the small passive monochrome LCDs typically used in clocks, watches and small appliances.

Mini-LED: Backlighting with Mini-LEDs can support over a thousand of Full-area Local Area Dimming (FLAD) zones. This allows deeper blacks and higher contrast ratio.MicroLED.)

Today, most LCD screens are being designed with an LED backlight instead of the traditional CCFL backlight, while that backlight is dynamically controlled with the video information (dynamic backlight control). The combination with the dynamic backlight control, invented by Philips researchers Douglas Stanton, Martinus Stroomer and Adrianus de Vaan, simultaneously increases the dynamic range of the display system (also marketed as HDR, high dynamic range television or FLAD, full-area local area dimming).

The LCD backlight systems are made highly efficient by applying optical films such as prismatic structure (prism sheet) to gain the light into the desired viewer directions and reflective polarizing films that recycle the polarized light that was formerly absorbed by the first polarizer of the LCD (invented by Philips researchers Adrianus de Vaan and Paulus Schaareman),

Due to the LCD layer that generates the desired high resolution images at flashing video speeds using very low power electronics in combination with LED based backlight technologies, LCD technology has become the dominant display technology for products such as televisions, desktop monitors, notebooks, tablets, smartphones and mobile phones. Although competing OLED technology is pushed to the market, such OLED displays do not feature the HDR capabilities like LCDs in combination with 2D LED backlight technologies have, reason why the annual market of such LCD-based products is still growing faster (in volume) than OLED-based products while the efficiency of LCDs (and products like portable computers, mobile phones and televisions) may even be further improved by preventing the light to be absorbed in the colour filters of the LCD.

A pink elastomeric connector mating an LCD panel to circuit board traces, shown next to a centimeter-scale ruler. The conductive and insulating layers in the black stripe are very small.

A standard television receiver screen, a modern LCD panel, has over six million pixels, and they are all individually powered by a wire network embedded in the screen. The fine wires, or pathways, form a grid with vertical wires across the whole screen on one side of the screen and horizontal wires across the whole screen on the other side of the screen. To this grid each pixel has a positive connection on one side and a negative connection on the other side. So the total amount of wires needed for a 1080p display is 3 x 1920 going vertically and 1080 going horizontally for a total of 6840 wires horizontally and vertically. That"s three for red, green and blue and 1920 columns of pixels for each color for a total of 5760 wires going vertically and 1080 rows of wires going horizontally. For a panel that is 28.8 inches (73 centimeters) wide, that means a wire density of 200 wires per inch along the horizontal edge.

The LCD panel is powered by LCD drivers that are carefully matched up with the edge of the LCD panel at the factory level. The drivers may be installed using several methods, the most common of which are COG (Chip-On-Glass) and TAB (Tape-automated bonding) These same principles apply also for smartphone screens that are much smaller than TV screens.anisotropic conductive film or, for lower densities, elastomeric connectors.

Monochrome and later color passive-matrix LCDs were standard in most early laptops (although a few used plasma displaysGame Boyactive-matrix became standard on all laptops. The commercially unsuccessful Macintosh Portable (released in 1989) was one of the first to use an active-matrix display (though still monochrome). Passive-matrix LCDs are still used in the 2010s for applications less demanding than laptop computers and TVs, such as inexpensive calculators. In particular, these are used on portable devices where less information content needs to be displayed, lowest power consumption (no backlight) and low cost are desired or readability in direct sunlight is needed.

A comparison between a blank passive-matrix display (top) and a blank active-matrix display (bottom). A passive-matrix display can be identified when the blank background is more grey in appearance than the crisper active-matrix display, fog appears on all edges of the screen, and while pictures appear to be fading on the screen.

Displays having a passive-matrix structure are employing Crosstalk between activated and non-activated pixels has to be handled properly by keeping the RMS voltage of non-activated pixels below the threshold voltage as discovered by Peter J. Wild in 1972,

STN LCDs have to be continuously refreshed by alternating pulsed voltages of one polarity during one frame and pulses of opposite polarity during the next frame. Individual pixels are addressed by the corresponding row and column circuits. This type of display is called response times and poor contrast are typical of passive-matrix addressed LCDs with too many pixels and driven according to the "Alt & Pleshko" drive scheme. Welzen and de Vaan also invented a non RMS drive scheme enabling to drive STN displays with video rates and enabling to show smooth moving video images on an STN display.

Bistable LCDs do not require continuous refreshing. Rewriting is only required for picture information changes. In 1984 HA van Sprang and AJSM de Vaan invented an STN type display that could be operated in a bistable mode, enabling extremely high resolution images up to 4000 lines or more using only low voltages.

High-resolution color displays, such as modern LCD computer monitors and televisions, use an active-matrix structure. A matrix of thin-film transistors (TFTs) is added to the electrodes in contact with the LC layer. Each pixel has its own dedicated transistor, allowing each column line to access one pixel. When a row line is selected, all of the column lines are connected to a row of pixels and voltages corresponding to the picture information are driven onto all of the column lines. The row line is then deactivated and the next row line is selected. All of the row lines are selected in sequence during a refresh operation. Active-matrix addressed displays look brighter and sharper than passive-matrix addressed displays of the same size, and generally have quicker response times, producing much better images. Sharp produces bistable reflective LCDs with a 1-bit SRAM cell per pixel that only requires small amounts of power to maintain an image.

Segment LCDs can also have color by using Field Sequential Color (FSC LCD). This kind of displays have a high speed passive segment LCD panel with an RGB backlight. The backlight quickly changes color, making it appear white to the naked eye. The LCD panel is synchronized with the backlight. For example, to make a segment appear red, the segment is only turned ON when the backlight is red, and to make a segment appear magenta, the segment is turned ON when the backlight is blue, and it continues to be ON while the backlight becomes red, and it turns OFF when the backlight becomes green. To make a segment appear black, the segment is always turned ON. An FSC LCD divides a color image into 3 images (one Red, one Green and one Blue) and it displays them in order. Due to persistence of vision, the 3 monochromatic images appear as one color image. An FSC LCD needs an LCD panel with a refresh rate of 180 Hz, and the response time is reduced to just 5 milliseconds when compared with normal STN LCD panels which have a response time of 16 milliseconds.

Samsung introduced UFB (Ultra Fine & Bright) displays back in 2002, utilized the super-birefringent effect. It has the luminance, color gamut, and most of the contrast of a TFT-LCD, but only consumes as much power as an STN display, according to Samsung. It was being used in a variety of Samsung cellular-telephone models produced until late 2006, when Samsung stopped producing UFB displays. UFB displays were also used in certain models of LG mobile phones.

Twisted nematic displays contain liquid crystals that twist and untwist at varying degrees to allow light to pass through. When no voltage is applied to a TN liquid crystal cell, polarized light passes through the 90-degrees twisted LC layer. In proportion to the voltage applied, the liquid crystals untwist changing the polarization and blocking the light"s path. By properly adjusting the level of the voltage almost any gray level or transmission can be achieved.

In-plane switching is an LCD technology that aligns the liquid crystals in a plane parallel to the glass substrates. In this method, the electrical field is applied through opposite electrodes on the same glass substrate, so that the liquid crystals can be reoriented (switched) essentially in the same plane, although fringe fields inhibit a homogeneous reorientation. This requires two transistors for each pixel instead of the single transistor needed for a standard thin-film transistor (TFT) display. The IPS technology is used in everything from televisions, computer monitors, and even wearable devices, especially almost all LCD smartphone panels are IPS/FFS mode. IPS displays belong to the LCD panel family screen types. The other two types are VA and TN. Before LG Enhanced IPS was introduced in 2001 by Hitachi as 17" monitor in Market, the additional transistors resulted in blocking more transmission area, thus requiring a brighter backlight and consuming more power, making this type of display less desirable for notebook computers. Panasonic Himeji G8.5 was using an enhanced version of IPS, also LGD in Korea, then currently the world biggest LCD panel manufacture BOE in China is also IPS/FFS mode TV panel.

In 2015 LG Display announced the implementation of a new technology called M+ which is the addition of white subpixel along with the regular RGB dots in their IPS panel technology.

Most of the new M+ technology was employed on 4K TV sets which led to a controversy after tests showed that the addition of a white sub pixel replacing the traditional RGB structure would reduce the resolution by around 25%. This means that a 4K TV cannot display the full UHD TV standard. The media and internet users later called this "RGBW" TVs because of the white sub pixel. Although LG Display has developed this technology for use in notebook display, outdoor and smartphones, it became more popular in the TV market because the announced 4K UHD resolution but still being incapable of achieving true UHD resolution defined by the CTA as 3840x2160 active pixels with 8-bit color. This negatively impacts the rendering of text, making it a bit fuzzier, which is especially noticeable when a TV is used as a PC monitor.

In 2011, LG claimed the smartphone LG Optimus Black (IPS LCD (LCD NOVA)) has the brightness up to 700 nits, while the competitor has only IPS LCD with 518 nits and double an active-matrix OLED (AMOLED) display with 305 nits. LG also claimed the NOVA display to be 50 percent more efficient than regular LCDs and to consume only 50 percent of the power of AMOLED displays when producing white on screen.

This pixel-layout is found in S-IPS LCDs. A chevron shape is used to widen the viewing cone (range of viewing directions with good contrast and low color shift).

Vertical-alignment displays are a form of LCDs in which the liquid crystals naturally align vertically to the glass substrates. When no voltage is applied, the liquid crystals remain perpendicular to the substrate, creating a black display between crossed polarizers. When voltage is applied, the liquid crystals shift to a tilted position, allowing light to pass through and create a gray-scale display depending on the amount of tilt generated by the electric field. It has a deeper-black background, a higher contrast ratio, a wider viewing angle, and better image quality at extreme temperatures than traditional twisted-nematic displays.

Blue phase mode LCDs have been shown as engineering samples early in 2008, but they are not in mass-production. The physics of blue phase mode LCDs suggest that very short switching times (≈1 ms) can be achieved, so time sequential color control can possibly be realized and expensive color filters would be obsolete.

Some LCD panels have defective transistors, causing permanently lit or unlit pixels which are commonly referred to as stuck pixels or dead pixels respectively. Unlike integrated circuits (ICs), LCD panels with a few defective transistors are usually still usable. Manufacturers" policies for the acceptable number of defective pixels vary greatly. At one point, Samsung held a zero-tolerance policy for LCD monitors sold in Korea.ISO 13406-2 standard.

Dead pixel policies are often hotly debated between manufacturers and customers. To regulate the acceptability of defects and to protect the end user, ISO released the ISO 13406-2 standard,ISO 9241, specifically ISO-9241-302, 303, 305, 307:2008 pixel defects. However, not every LCD manufacturer conforms to the ISO standard and the ISO standard is quite often interpreted in different ways. LCD panels are more likely to have defects than most ICs due to their larger size. For example, a 300 mm SVGA LCD has 8 defects and a 150 mm wafer has only 3 defects. However, 134 of the 137 dies on the wafer will be acceptable, whereas rejection of the whole LCD panel would be a 0% yield. In recent years, quality control has been improved. An SVGA LCD panel with 4 defective pixels is usually considered defective and customers can request an exchange for a new one.

Some manufacturers, notably in South Korea where some of the largest LCD panel manufacturers, such as LG, are located, now have a zero-defective-pixel guarantee, which is an extra screening process which can then determine "A"- and "B"-grade panels.clouding (or less commonly mura), which describes the uneven patches of changes in luminance. It is most visible in dark or black areas of displayed scenes.

The zenithal bistable device (ZBD), developed by Qinetiq (formerly DERA), can retain an image without power. The crystals may exist in one of two stable orientations ("black" and "white") and power is only required to change the image. ZBD Displays is a spin-off company from QinetiQ who manufactured both grayscale and color ZBD devices. Kent Displays has also developed a "no-power" display that uses polymer stabilized cholesteric liquid crystal (ChLCD). In 2009 Kent demonstrated the use of a ChLCD to cover the entire surface of a mobile phone, allowing it to change colors, and keep that color even when power is removed.

In 2004, researchers at the University of Oxford demonstrated two new types of zero-power bistable LCDs based on Zenithal bistable techniques.e.g., BiNem technology, are based mainly on the surface properties and need specific weak anchoring materials.

Resolution The resolution of an LCD is expressed by the number of columns and rows of pixels (e.g., 1024×768). Each pixel is usually composed 3 sub-pixels, a red, a green, and a blue one. This had been one of the few features of LCD performance that remained uniform among different designs. However, there are newer designs that share sub-pixels among pixels and add Quattron which attempt to efficiently increase the perceived resolution of a display without increasing the actual resolution, to mixed results.

Spatial performance: For a computer monitor or some other display that is being viewed from a very close distance, resolution is often expressed in terms of dot pitch or pixels per inch, which is consistent with the printing industry. Display density varies per application, with televisions generally having a low density for long-distance viewing and portable devices having a high density for close-range detail. The Viewing Angle of an LCD may be important depending on the display and its usage, the limitations of certain display technologies mean the display only displays accurately at certain angles.

Temporal performance: the temporal resolution of an LCD is how well it can display changing images, or the accuracy and the number of times per second the display draws the data it is being given. LCD pixels do not flash on/off between frames, so LCD monitors exhibit no refresh-induced flicker no matter how low the refresh rate.

Color performance: There are multiple terms to describe different aspects of color performance of a display. Color gamut is the range of colors that can be displayed, and color depth, which is the fineness with which the color range is divided. Color gamut is a relatively straight forward feature, but it is rarely discussed in marketing materials except at the professional level. Having a color range that exceeds the content being shown on the screen has no benefits, so displays are only made to perform within or below the range of a certain specification.white point and gamma correction, which describe what color white is and how the other colors are displayed relative to white.

Brightness and contrast ratio: Contrast ratio is the ratio of the brightness of a full-on pixel to a full-off pixel. The LCD itself is only a light valve and does not generate light; the light comes from a backlight that is either fluorescent or a set of LEDs. Brightness is usually stated as the maximum light output of the LCD, which can vary greatly based on the transparency of the LCD and the brightness of the backlight. Brighter backlight allows stronger contrast and higher dynamic range (HDR displays are graded in peak luminance), but there is always a trade-off between brightness and power consumption.

Low power consumption. Depending on the set display brightness and content being displayed, the older CCFT backlit models typically use less than half of the power a CRT monitor of the same size viewing area would use, and the modern LED backlit models typically use 10–25% of the power a CRT monitor would use.

Usually no refresh-rate flicker, because the LCD pixels hold their state between refreshes (which are usually done at 200 Hz or faster, regardless of the input refresh rate).

No theoretical resolution limit. When multiple LCD panels are used together to create a single canvas, each additional panel increases the total resolution of the display, which is commonly called stacked resolution.

As an inherently digital device, the LCD can natively display digital data from a DVI or HDMI connection without requiring conversion to analog. Some LCD panels have native fiber optic inputs in addition to DVI and HDMI.

Limited viewing angle in some older or cheaper monitors, causing color, saturation, contrast and brightness to vary with user position, even within the intended viewing angle.

Uneven backlighting in some monitors (more common in IPS-types and older TNs), causing brightness distortion, especially toward the edges ("backlight bleed").

Display motion blur on moving objects caused by slow response times (>8 ms) and eye-tracking on a sample-and-hold display, unless a strobing backlight is used. However, this strobing can cause eye strain, as is noted next:

As of 2012, most implementations of LCD backlighting use pulse-width modulation (PWM) to dim the display,CRT monitor at 85 Hz refresh rate would (this is because the entire screen is strobing on