can you fix a lcd screen without replacing it quotation

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

This article was co-authored by Linh Le and by wikiHow staff writer, Nicole Levine, MFA. Linh Le is a Certified Mobile Repair Specialist and the Owner of SC Mobile Repairs in San Clemente, California. With more than 12 years of experience, he specializes in smartphone, tablet, and smartwatch hardware repair. Linh has an iTech Mobile Device Repair Certification and an iOS Certification. He holds a Bachelor’s degree from The Franciscan University of Steubenville.

The term ‘flat screen’ applies to a wide range of TV types, from LCDs to the latest 4K and Smart models. A flat screen means the TV’s screen surface is flat rather than convex like older models. There can be several different types of flat-screen TVs, from older LCD to the newest Smart and 4K TVs. The type impacts the repair costs because more advanced and expensive TVs have more costly components to replace or fix. In addition, some TV repairs may not always be possible on that type. For example, it is not possible to replace the screen on a plasma TV if it cracks and begins to leak. The table below shows common television types and average repair costs for each:

Repairs for LCD TVs cost between $60 and $400. LCD televisions are one of the most popular options on the market, available in a wide range of sizes and styles. They use an LCD (liquid crystal display) with backlights to produce images. The backlights, screen, and other components may get damaged over time and need repairing.

LED TV repairs range from $60 to $400, depending on the scale of the problem. LED televisions are a specific type of LCD TV that use LED backlights to illuminate the liquid crystal display. These TVs usually produce more colorful and vibrant images and are more energy-efficient, but the LED backlights may need to be repaired or replaced over time.

4K TV repairs range from $100 to $275. A 4K television provides some of the clearest and most detailed images because of the very high resolution of its screen, providing more engaging viewing experiences. There are different types of 4K TVs, including some that use LED and others that use OLED. Basically, a television is considered 4K if it has ultra high definition. These models can be expensive to purchase and repair, but in many cases, repairs may not be possible on these units. So, their overall repair costs may be lower simply because some repairs may not be offered.

OLED TV repairs cost between $100 and $400 on average. They are the next step up from a standard LED TV, with OLED standing for organic light-emitting diodes. OLED televisions can achieve deeper blacks and higher contrast compared to standard LED screens. However, they can be very expensive to purchase and repair.

Plasma TV repairs average $100 to $400. These televisions are made up of pixels filled with gas that light up when an electrical current is applied. They are less popular today, and most companies have stopped making them. But they can still be found in many homes and are subject to problems like screen burn and distorted colors. While some repairs on these TVs are possible, many issues cannot be repaired due to their design.

Smart TV repairs cost between $100 and $400. These TVs have Smart technology and connect with your home’s WiFi network to download updates and access apps and the internet. They are more advanced than other TVs but still have various components that can break and require repairs. Many Smart TVs can have basic components. So even though they may be more expensive to purchase, they are not necessarily the most expensive to repair. That comes down to how the television is made and what makes it Smart.

TVs are made up of various parts and components, all working together to produce lights, colors, pictures, and sounds for your entertainment. Over time, accidents may happen that damage these parts, or they might just wear down over the years through repeated use. The table below shows common TV repairs and the costs for each.

HDMI port repairs for a TV costs between $60 and $250. Sometimes, HDMI ports fall out of position and may simply need to be repositioned. In other cases, one might stop working due to a more serious fault and require technical repair work.

TV speaker repairs range from $75 to $250, depending on the type and damage done to the speaker. Faulty speakers may simply need rewiring or minor adjustments, or they could need to be cleaned or replaced, so the exact costs and amount of work vary.

Backlight repairs average $100 to $150. The backlight is what illuminates the display of your television, providing the brightness and color. It may be in the form of LED light strips or fluorescent lights, depending on which television type you have. If these lights develop a problem, a repairman must open it up and make adjustments to get them functioning again.

TV inverter repairs cost between $100 and $200 each. The inverter powers up the backlights for your television, and they can stop working if their capacitors break down. Repairs are made by fitting new capacitors in place.

Water damage repairs on a TV range from $150 to $400. In some cases, if too much water has gotten into the TV, it may be beyond repair. In less severe situations, a repairman will take the television apart, dry it out, and put it back together successfully, repairing any damaged components.

TV screen repairs cost between $200 and $400, but in many cases, repairing the screen is not possible. Since the screen is usually the most expensive part of the television and one of the most sensitive to impacts and other damage, an expert may advise you to simply buy a new television instead of having it repaired. It is worth getting a diagnosis if the screen issue is not too severe because issues like flashing pixels or distorted colors may be fixable.

TV panel repairs average $200 to $400 in some cases, but some panels cannot be repaired. For this reason, many companies do not offer panel repair. So if your television gets a crack in the panel, you may be better off buying a new unit instead.

Power board repairs cost between $200 and $400. The power supply board allows it to turn on and function, and if it breaks down in any way, it may simply stop turning on. Often, a repairman can replace some of the capacitors and make other adjustments to repair a faulty board, rather than having to replace it entirely.

In some cases, your TV components may not be able to be repaired, or it might be more cost-effective to replace them with new ones. The repair price includes the cost of new parts, plus the labor required to fit them into place and remove the broken components. While some components can be replaced, they may be extremely expensive or cost-prohibitive to do so. This is mainly in the case of panels and screens because they often contain too many parts to replace on their own. The table below shows average costs for a variety of common replacements:

Fuse replacement in a TV costs between $60 and $150 and is one of the easier replacement jobs for a repairman. Glass and ceramic fuses on your TV’s power supply board may blow in certain situations and need replacing. To replace a fuse, the repairman opens the TV to access the power panel and swaps out the fuse.

Replacing a TV capacitor is inexpensive, starting at $60 up to $200. If more than one capacitor needs replacing, it is usually less expensive to replace the entire board. Capacitors cannot be repaired, so replacement is the only option.

TV bulb replacement costs average $75 to $200. Bulbs are usually found only in older models of LCD TVs or projection TVs. They are used to illuminate the display so that the picture can be seen. Bulbs are relatively easy to replace, but the material costs are a little higher with bulbs when compared to other components, leading to varied replacement prices from model to model.

TV backlight replacements cost between $100 and $200 on average, depending on the television size and scale and the type and number of lights required. If you have LED lights, parts may be more expensive, leading to higher total costs. Usually when backlight problems occur, the bulbs or diodes are dead and need to be replaced.

Picture tube replacements range from $200 to $300 on average. Picture tubes, also known as cathode ray tubes or CRTs, are only used in older TVs. So, this is not a replacement job you need to worry about with an LED or LCD TV.

HDMI port replacement on a TV costs between $200 and $300. Damaged or broken ports may simply stop working or be incompatible with certain HDMI cables. In this case, a new port must be fitted and connected to the circuit board, requiring a couple of hours of labor.

TV motherboard replacements average $200 to $400. Often when a problem occurs with a motherboard, it needs to be completely replaced rather than repaired. The motherboard controls the TV’s functions and features, and a broken motherboard makes your television completely unusable.

TV screen replacement costs at least $400 to $1,000 and often much more. The screen is the most expensive part of a TV. So usually, the cost of replacing it is higher than just buying a new unit. In some cases, this is because the screen cannot be replaced without also replacing most of the other components, particularly for TVs like LED, LCD, or plasma. Most professional repair companies do not offer screen or panel replacement as a service.

TV panel replacement costs a minimum of $400 to $5,000 and often a lot more on some of the high-end 4K and Smart screen displays. Because the cost of a replacement panel is so high, it is usually more cost-effective to simply purchase a new television. Like the screen, this is due to the number of components involved. Therefore, most repair places will not offer panel replacement as a service.

You might not know exactly which part of your TV is broken or damaged at first. The symptoms of a broken television vary from vertical colored lines across the screen to audio issues, power problems, and even situations where the television starts normally but then turns itself off. For this reason, most repairs start with a diagnostic so that the problem can be found and a plan made for repair. For some repairs to be made, the part will need to be replaced, while in other cases, repair or replacement of that part may not be possible. The table below shows common problems and average repair costs for each.

Repairing a TV that will not turn on costs between $60 and $400 because there are many potential causes. It might be something as simple as a blown fuse, which can be replaced quite cheaply. Or, it could be a motherboard or power supply issue, which is more costly to fix.

Damaged cables on your TV can be repaired for between $75 and $200 in most cases. Over time, cables can get frayed, twisted, or broken, but professionals can cut away the damaged parts, add in new connectors and repair the damage, or simply replace the bad cables with new ones.

Expect to pay between $75 and $400 to repair a television with no sound. There are various reasons why your TV’s sound stopped working. It is most likely a fault with a speaker, which can be repaired or replaced. Or, it could be a deeper issue associated with the motherboard, which may also need fixing or replacing.

Repairs for this problem cost between $100 and $200. If your TV’s picture appears for a moment and then vanishes, it is most likely an issue with the inverter. A repairman will open it up, diagnose the issue, and decide on the most efficient solution.

Repairing vertical lines on the screen averages $150 to $400. This is usually an issue associated with your TV’s control board or motherboard, which may be damaged and need to be either repaired or replaced. It could also be caused by a loose cable, but it will need to be opened up to diagnose the issue and repair it.

Repairing horizontal lines on your TV costs between $150 and $400. It might be an issue with the motherboard, or it could be a problem with loose cables between the panel and the control board. To fix this issue, the television needs to be opened up and analyzed by a professional repairman.

Repairing a cracked TV screen costs from $400 to $1,000 or even more. Cracked screens cannot be repaired, they can only be replaced, and they are very expensive, sometimes exceeding the cost of a new TV. For this reason, if you have a cracked screen, it will probably have to be replaced entirely.

There are many different brands and companies that make TVs. Some brands specialize in certain types, while others make a wider range of products. It is common for the brand to impact the cost of repair because there may be specific issues or costs related to that brand.

While you may choose a specific brand based on the technology, cost, or resolution, keep in mind that brands may also have varying costs for repairs and the repairs types that may be available. Regardless of brand, most TV repairs fall between $60 and $400, although some repairs may be higher.

The cost to fix a Philips TV is $60 to $100. The typical issue with Philips televisions seems to be that they have a mind of their own. They turn on and off and sign in and out of apps randomly. While a solution doesn’t seem to be forthcoming, Philips is steadily losing customers due to a firmware problem.

Fixing a Sony TV will cost you about $60 to $400. This popular brand has a reputation for simply becoming disabled with no power or sound. Unfortunately, the customer service at Sony isn’t always the best. Customers are often frustrated when it comes to warranty work.

To fix your TCL TV blank screen, you should expect to pay about $60 to $400. One characteristic repair of the TCL brand is a black screen with no picture. This can be a fuse that has blown, or it may require a major change, such as a new main board.

Damaged cables can cause a TV to flicker or grow dim. Repair prices for damaged cables are $75 to $200. Samsung TV owners cite this flickering or dimming of the screen as a common issue with this brand. Sometimes the settings for the eco sensor1 or the energy-saving feature create this problem. Turning either of those off may fix the issue.

Some of the most common issues with this brand are banding at a repair cost of $100 to $200 or sound with a cost of $150 to $400. Color problems may be related to adjustment and can be fixed for a low cost of $75 to $100, HDMI connections are often fixed at the cost of $200 to $300, and streaming problems may be corrected with a software update. Software updates can be done by the owner, but a repairman will most likely charge a minimum fee of $75 to $100. Banding presents as sections of bands where it should be smooth. Sound and color can go out over time in the LG brand. HDMI and streaming can become difficult as technology emerges and changes.

Hisense TVs have a history of display difficulties and could cost you about $100 to $200. Typically, it means you need a new inverter, or it could signal the beginning of the end for your Hisense television.

Panasonic TV owners often experience the power clicking on and off and may need a new main board at the cost of $200 to $400. The reset button may help. The repairman will need to replace the motherboard of the TV if that fails.

The Vizio TV is known for its screen of death (a blank or black screen) and usually costs about $200 to $400. The problem is most often a blown motherboard, and replacement is the only option. A factory reset may be a solution. If that doesn"t work, the motherboard is the best possible answer.

Labor costs for TV repair vary depending on whether you have the television repaired in your home or drop it off at a repair center. Having someone come to your home will have higher costs than taking it to a technician.

A television repair technician has earned a career certificate or Associate’s degree in electronics technology or a related field. Expect to pay between $40 and $60 per hour in labor for someone to fix your television. Some technicians have minimum costs for some repairs, particularly if they travel to you. In this case, you may find that even if the repair only takes an hour, you may need to pay a minimum of two hours of work.

The amount of time to repair your TV depends on what the problem is and the availability of parts. Most jobs can be completed in 1 to 3 hours when the parts are on hand.

Most technicians charge you a diagnostic fee upfront. This fee is for determining what the problem is and can run between $75 and $150. The cost is often waived if you allow the shop’s technicians to make the repairs for you.

Often, you must decide whether it is worth repairing your TV because in many situations, the cost of repairs is higher than the price of a new TV. For example, when screens are cracked or damaged, the cost of replacing a panel is usually much higher than simply buying a new TV.

Consumer Reports recommends replacing electronics whenever the cost of repairs equals or exceeds half the cost of a new purchase. It is also recommended that you replace your television if the new version is less than $200, or if your screen is smaller than 32”. For example, it costs around $150 for a new motherboard in an LG Model 24LF452B 24” TV, which takes around one hour to repair. As a result, you would pay between $190 and $210 to repair your old set, while it is possible to purchase a new one for less.

If you invested a lot of money in your television, the costs of repairing an inverter or getting new backlights may be far cheaper than replacing it. This is why it is often best to ask a professional to diagnose the problem and give you a quote for the repair work. Then, you can compare the price of repairs against the cost of a new TV and decide what makes sense. If your TV breaks down repeatedly, you have multiple repair bills over the course of a year. It might be time for a new television even if a single repair does not seem too expensive.

To minimize repairs and help your TV stay in working order for as long as possible, take care of it as well as you can. Here are some useful TV maintenance tips:Do not leave the TV on if you are not actually watching it. They can run for tens of thousands of hours, but there is no need to waste those hours. So, avoid leaving it on in the background, and make sure to turn it off when you leave the room.

Try not to leave your TV on for too long at a time. Like other appliances, televisions can start to get very hot the longer they are left on. They need to be turned off now and then to get a chance to cool down and rest before being switched back on.

Keep your TV clean. Over time, dust, pet hair, and bits of dirt can build up on the screen and get inside the television via vents and ports. This dust accumulation can affect a TV’s operation and make it more likely to break down.

Consider using a surge protector to keep your TV and associated devices and appliances safe. This can be especially important in areas that experience a lot of storms or frequent power cuts because sudden cuts and surges easily damage your TV’s components.

When positioning your television, leave space around it to provide airflow. This helps prevent the TV from overheating and cools it down more quickly when you turn it off.

Additional Considerations and CostsDIY. In some cases, television repair can be performed as a DIY project. There are numerous how-to videos available that are easy to watch and understand. Parts for most sets are also available online. However, if you are not comfortable with the process, always call a technician rather than attempting the repair yourself.

DIY issues. While DIY repair is often possible, it is not frequently recommended. There is some risk of electrocution, and you might also damage the TV even more by improperly installing a t-con board or ribbon connectors. If you are in doubt, it is best to leave this job to a professional.

Obvious solutions. Before seeking repairs, first look for the obvious. If your set will not power on, it could be a problem with your outlet and not your TV. Try plugging your television into a different outlet to see if that resolves the problem. If that does not fix it, ensure you have not tripped a breaker, and check that the power cord is fully seated.

Remote control. A set that powers on and off at random is sometimes caused by issues with the remote. Try removing and replacing the batteries or using a different remote if possible.

Warranty. When purchasing a new television, buying an extended warranty can spare you the unwanted expense of repair bills in some cases. An extended warranty is largely based on the price of your television. Expect to spend between 10 and 20 percent of your set’s cost on an extended warranty to help cover damage. Ordinary warranties only cover manufacturer’s defects and, therefore, cannot be used to pay for damage due to neglect or accidents.

Warranty repairs. When having warranty repairs made, drop the set off at a local shop whenever possible or have them come to you. If you need to ship the television off, get a tracking number so that you can locate your set if it gets lost.

Scams. Television repair scams are quite common. Before hiring someone to fix your set, find out what experience and training that person has. Check references and online reviews as well.

In-shop repairs. In-shop TV repair services may involve a pick-up and delivery charge if you do not take it in yourself. While some may do this for free, others charge between $40 and $75 to pick-up and deliver the TV back to you. Additionally, customers that live in rural areas may have to ship the television. If you do this, make sure you obtain a tracking number and proof of delivery. The repair service will contact you with the list of recommended repairs and the cost and request a debit or credit card to pay for the repairs before completing them.

Television repair costs vary widely, but the average consumer pays between $100 and $300. Prices depend on the make, model, and size of your set, as well as the availability of parts. It is generally more expensive to repair an older model than it would be to replace it. New televisions are becoming more affordable every year, but the price of parts remains steady or even increases as older parts become rarer.Can a flat-screen TV be fixed?

Yes, flat-screen TVs can frequently be fixed, including issues with the screen, sound, lighting, cables, and interior components. However, there are some situations where flat-screen TVs cannot be fixed, such as when the screen is severely cracked.How do you fix a broken TV screen?

Not all TV screens can be fixed or replaced. Certain types have components behind the screen that can be damaged by its removal. However, if you choose to proceed, remove all external cables, unplug your set, and lay it face down on a flat, soft surface. Remove any screws holding the frame in place and then gently remove the frame and set it aside. Put your new screen in place and reconnect the internal cables in the same manner you disconnected them. It is usually best to get a professional to handle TV repairs, and the cost of replacement screens is often very high. So, it may be more cost-effective to get a new TV.How many years will a flat-screen TV last?

This depends on the make and model of your TV and your viewing habits. Many modern TVs last 60,000 viewing hours or more, equating to 30+ years for a typical person. However, its lifespan can be reduced if it is not properly maintained and cared for.Does turning the TV off shorten its life?

No, turning a TV off will not usually shorten its life in any way. It is actually recommended to turn TVs off when you are not using them, allowing them to cool down and extend their lifespan.Is it okay to leave a TV on all night?

This is not recommended. If you leave a TV on for too long, it may overheat, which could damage interior components like the motherboard. It may also do damage to the screen and risk ‘burning’ an image into the display, as well as damaging the backlights.Do Smart TVs use more electricity?

Generally, no. Most modern Smart TVs are designed to be as energy-efficient as possible, with some models even using less energy than conventional TVs. It all depends on the TV make and model.

A dying or cracked display doesn’t mean your laptop is a paperweight. For most laptops, a screen replacement takes $80 and an hour of your time at most. If you’re a DIYer, replacing a broken laptop screen yourself is a great way to save cash, as most computer repair shops will quote you $150 to $300 for the job.

Before doing anything, give your laptop a full look-over and inspection to ensure the screen really needs replacement. If the graphics card on the motherboard is dead, for instance, you may be wasting your time and effort on replacing a perfectly good screen. Additionally, if the laptop has been recently dropped or otherwise possibly physically harmed, you’ll want to double-check for other damage as well.

To ensure the graphics card is functioning, you can plug a desktop monitor or TV into the laptop, as most have a standard blue VGA monitor and/or a HDMI output. If the picture looks good on an external display, your graphics card is likely good and the screen is at fault. If you don’t get any picture, keep in mind some laptops require you to press certain function keys on the laptop to activate external display output. If you do that and video still doesn’t display, your graphics card and/or motherboard is likely broken, rather than your screen.

If the laptop outputs to another display successfully, use the computer for a while to ensure the keyboard and other laptop components appear to be functioning normally.

Before you replace your laptop’s LCD, here are the caveats to the general steps that follow. This is not meant to be a guide for ultrabooks, two-in-ones, tablets, Macbooks, or other, more specialized notebooks, however. It’s more for average, run-of-the-mill laptops. But even then the general steps I discuss do not work for all such laptops. Some will require a different process and/or more work to replace the screen, such as accessing the motherboard by opening the main case of the laptop.

Because of that crucial caveat, before buying a new LCD, it may be a good idea to try to remove the damaged screen first, to ensure you can perform the replacement. If, after following the first few steps the process looks different for your laptop, I recommend scouring Google and YouTube or finding a repair professional for further help on your exact laptop brand and model.

Finding a replacement LCD is typically easy—and you don’t have to pay the crazy prices the manufacturer usually wants. Just search eBay, Amazon, or Google with your laptop model number and the words LCD screen. You’ll find most regular screens can be had for as low as $50 to $80. If you aren’t finding anything, try other identification numbers from the laptop label or documentation. Some vendors have one or two different sets of identification numbers that could serve as your model number.

When shopping for the LCD, most sellers will alert you to compare the specs and placement of the video cable on the back of their screen to your current screen. This is another reason to crack open the laptop bezel before ordering a replacement. However from my own experience, if the seller says the screen is compatible with your exact laptop model, it usually works.

Table or other flat working area: You’ll need a spot to sit (or stand, if that’s your thing) with a flat area to work on your laptop. This gives you a reason to clean off that messy dining-room table or desk.

Small-head magnetic philips screwdriver: Not small like a mini screwdriver from an eyeglass repair kit, but I’d say between that size and a mid-sized screwdriver would work. If you don’t have a magnetic-head screwdriver, try to find a magnet big enough to magnetize the driver head. This helps the screws stick to the head, making it much easier to remove and replace the screws without cursing as they fall all over the place.

Plastic putty knife or other thin object: This is optional, to aid in prying apart the screen bezel from the case. Personally, my finger nails usually do the trick. If you do use another object, ensure it’s thin enough but not so sharp that it will leave scrapes or other evidence of prying.

Find the round cover stickers that are hiding the screws on the screen bezel, the case surrounding the screen. These stickers are usually on the bottom of the bezel, near the screen hinges, when you have the screen opened. You should find one on each side of the screen.

You can see the screw covers in the very bottom right and left corners on the bezel of this Acer Aspire One. (Click any image in this article to enlarge it.)

Use a sharp, pointy object—like an opened safety pin or needle—to help remove the cover stickers without damaging them. Stick it between the edge of the cover and bezel, and then pry the sticker away. Once removed, place the covers in a safe spot, with the sticky side up to help ensure there’s enough stickiness when you place them back on.

Use your screwdriver to remove the now-exposed screws. Remember: righty-tighty, lefty-loosey. Some screws are easy to remove; others, not so much. But moving the screen into just the right position usually exposes the screws enough for removal.

Carefully start prying the screen bezel away from the back side of the screen case. Work a fingernail or other thin, prying object into the crack around the outside of the screen. The bezel is usually secured to the back case with plastic snaps, so give it some force while prying—but not too brutish. You’ll hear the unsnapping of the fasteners when prying.

Once you’ve unsnapped the screen bezel, it may or may not be easy to remove. If not, it’s likely stuck around the screen hinges. Moving the screen position up or down, with some gentle force if necessary, should free it fully.

Once the bezel is fully removed, you’ll find the LCD secured to a metal trim frame on the left and right sides. Remove the two screws (one on each side, on the top) holding the trim frame pieces to the back screen case. Now, you should be able to lift the LCD (with the trim frame pieces attached) slightly away from the back screen case.

On each of the trim frames’ sides, remove any screws that are securing it to the LCD. Most laptops have three screws on each side; however, the smaller laptop I photographed here doesn’t have these screws—the LCD is actually secured to the trim frame pieces by tape on each side.

Now you should be able to set the LCD face-down onto the keyboard. Be careful not to put excessive force on the video cable attached to the back of the LCD.

Disconnect the video cable from the back of the LCD. Though the laptop I photographed here has the connector on the very bottom, most laptops have the connector near the center. If so, keep in mind that the portion of the cable running down the screen is usually stuck on the back of the screen with some mild adhesive. Just gently pull the cables away from the screen. You usually must remove tape that’s securing the video connector to the back of the screen as well. When you get to the point of actually pulling the video cable out of the screen connector, it should unplug with little force.

Once you’ve fully removed the broken LCD, simply place the new one face-down like you did the old one. Reattach the video cable to the connector and place the cables and any tape just like they were for the old one.

Set the new screen up in the side trim frame pieces, then re-secure it like the old one was: usually three screws in each side of the trim frame pieces, and then a screw on top of each to secure it to the back screen case.

When you get to the point of putting the bezel back on, just line it up and push/squeeze the bezel back into the snaps of the rear screen case. Before replacing the bezel screws, ensure the bezel is fully snapped in place and no crack exists around the edges of the screen case. Lastly, use that safely pin or needle to reattach the sticky screw covers.

When you drop your device, you may immediately pick it up and try to turn it on to see what happened. Sometimes, the screen will be completely cracked, but there’s still a display. Other times, the screen is cracked and there is no display. A few different things happen when an iPad or iPhone drops. Understanding what happens to the screen can help you know what type of repair you need.

When you drop your iPad or iPhone and the screen doesn’t come on (there is no display) or the display is distorted, it’s likely the LCD screen is broken. This screen has everything to do with seeing what you love about your device. Videos, games, email, and everything else depends on your LCD screen.

Sometimes, you may be able to see the screen, but when you touch it to do something, it won’t react to your touch. This is usually because the digitizer is damaged. Many times, this happens even when you can’t see a crack on your device. This is why many people don’t think they need a screen replacement, and actually, in some cases they still don’t need it. Other components may be damaged that cause the touch not to work, but when those are all working okay, it’s the screen.

There are some cases in which both the LCD and digitizer need to be replaced. If there’s no display or a distorted one AND there’s no touch response, the LCD and digitizer need to be replaced. This is usually what people need when they turn to us with a shattered iPad or iPhone.

If you still don’t know if you should have a LCD or digitizer repair, contact our certified technicians. They can look at your device for free to provide you a repair quote. You can trust our technicians to give you the truth, so you can save money when you may not need both screens replaced. If you do, you can be sure that you’ll receive a quality repair with quality parts.

TV repair costs between $60 and $350 with most spending $207 on average for LCD, LED, plasma, and 4K TVs; costs are higher if repairing older DLP, projection, and HD TVs. TV problems like display issues, powering-on problems, or sound issues can be fixed. Pickup and delivery fees may apply.

The cost to repair a TV will include the price of parts and labor costs, plus other associated costs. Additional charges include a trip fee for a technician to come to your home, a fee to transport your TV to and from a repair shop, and the diagnostic fee to determine what needs to be replaced.

The cost to repair a TV screen can be significantly more than the cost of purchasing a new TV. For this reason, replacing or repairing a broken TV screen is not considered feasible.

For example, the price of a new Samsung 40-inch LED TV is about $400, yet the cost of a replacement display panel for this model is about $380. This price is only for the replacement part and does not cover diagnostic costs, labor costs, or travel or shipping fees.

Broken TV screen repair is not a service offered by most TV or electronics repair companies. For example, BestBuy"s 90-day warranty, does not list broken TV screen repair as one of the problems they service.

Unless you are trying to fix a TV from the ’80s or earlier, cracked TV screen repair is not feasible; the entire display panel must be replaced instead. The cost of a replacement TV display panel is more than the cost of buying a new TV, and that’s before labor and other service costs.

The cost of TV screen replacement is generally the same as or more than the cost of buying a new TV. Therefore, replacing a broken or malfunctioning TV screen is not considered a viable option. If the TV is under the manufacturer’s warranty, the manufacturer may replace the entire unit.

TV manufacturers do keep replacement TV screen panels on hand to support products under warranty in case the screen malfunctions, due to manufacturer defect.

If you still want to replace a damaged or malfunctioning TV screen, your best option is to find a used replacement panel or a broken TV of the same model on which the screen is still functional. You might find one on eBay, and you can hire a technician to change out the panel.

The cost of a used replacement TV panel ranges from $50 to $350 or more, excluding shipping, depending on the brand and size. Note that the chances of finding exactly the part you need in excellent condition are slim, and the cost excludes the cost of installation by a repair shop.

Whether your TV is LCD, LED, plasma screen, or 4K (Ultra HD), the cost to fix common problems ranges from $60 to $350, depending on the repair type and the brand of TV being repaired.

These repair problems could have more than one possible source, so a technician should take time to narrow down the exact problem. TVs are repaired by replacing faulty components.

TV motherboard replacement costs between $200 and $350, including parts and labor, or about $275 on average. Motherboard replacement parts range from $35 to $199and labor costs from $60 to $125.

A TV inverter repair costs $104 to $171, including parts and labor, with an average cost of $138 for a TV with one inverter board or $178 for two. Parts range from $7 to $74, and the average labor cost for TV inverter repair is $97 per hour.

The function of an inverter board in a TV is to power the backlight of the screen. The inverter board requires a few hundred volts of power. If the inverter board goes bad, this would cause the TV to power on and have sound but no picture.

When an inverter component goes bad, it is usually replaced rather than repaired. In some cases, the capacitors on a converter board fail, and a technician can fix it by replacing the capacitors rather than replacing the entire inverter component. However, if an entire inverter board replacement is not available for the model of TV being repaired, replacing the capacitors may be the only option for TV inverter repair.

A flat-screen TV bulb replacement costs between $60 to $115, with most homeowners spending $84 for parts and labor. The price for replacement bulbs ranges from $18.50 to $80.

If an older model LCD TV or projection TV powers on and has sound but no picture, this may be due to lamp burnout, which is both common and expected. In this case, replacing the bulb will fix the problem. An experienced technician should be able to replace the bulb quickly and easily.

TV backlight repair costs $100 to $122, including replacement parts and labor, at a repair shop. In-house repair costs are more due to trip fees. The price of backlight replacement parts averages around $2.50for each LED and between $20 and $25 for each CCFL strip.

If the CCFL strips for your TV are no longer available, a technician can convert the backlight from CCFL to LED using the same number of backlighting strips. Each strip of LEDs costs between $12 and $30.

A new inverter may be needed to power the LEDs, costing between $7 and $74before labor, or an average of $40. In some cases, a repair shop can convert a CCFL backlight to LED without installing a new inverter.

Backlight failure in a TV may also be due to failure of the power inverter that supplies power to the backlight. In rare cases, both the inverter and the lighting components fail.

Repairing a TV power supply board costs $23 to $234 for parts alone. Completely replacing the power supply board costs $250 for parts and labor. If one capacitor has failed, the cost for replacement capacitors is low. However, it’s more cost-effective for the technician to replace the entire board rather than spend time trying to diagnose and replace faulty capacitors one by one.

The cost to fix an HDMI port on a TV is $93 to $302. In some cases, the input circuit board that the HDMI port connects to may be damaged and need to be replaced. The cost for replacing this input circuit board, including labor, ranges from $200 to $350.

TV capacitor repair costs $60 to $129, including parts and labor. The cost for the replacement part ranges from $0.06 to $14, with the labor portion ranging from $60 to $125 per hour. TV capacitors protect the circuit from getting too much power, filter signals, and facilitate changing channels.

It is not possible to fix a TV capacitor when it fails; it needs replacing. If your TV stops working while you are using it and you notice a smell similar to ammonia or bleach, this is a sign that a capacitor has blown. However, some capacitors do not make any noticeable smell when they blow.

Flat screen replacement glass is not available. The only option for flat-screen TV glass repair is to try optical glass glue, which costs $1.70 for a 5-ml. tube. This may be an option for TV glass repair if the crack is only a few inches or less. TV panels are built as one unit at the factory, with the glass adhered to the display panel.

In-home CRT repair ranges from $199 to $249. The cost of repairing a CRT picture tube ranges from $199 for a TV that is 27 inches or smaller to $249 for a TV that is 28 inches or larger.

Picture tubes, or cathode-ray tubes (CRTs), were used in old TVs, which had much poorer image quality than modern TVs and were much bulkier and heavier.

A TV fuse repair costs between $61 and $136, with most spending $99 on average. The cost of the replacement fuse itself is $1.50 to $11, while labor ranges from $60 to $125 per hour. Additional fees may apply.

LCD flat-panel repair is not considered cost-effective. If the glass is cracked or the display is physically damaged, it is cheaper to replace the entire TV than to repair or replace the display panel.

Estimating TV repairs costs by brand is not something TV repair shops offer, however, there are general prices by type. When looking for specific repair costs for your TV, you’ll find them in the common repairs price list above. Pricing applies to brands such as Samsung, LG, Sanyo, TCL, Insignia, HiSense, Sony, Toshiba, Pioneer, and Vizio.

More popular TVs are usually less expensive to repair because repair shops order replacement parts for them in bulk, which allows them to buy those parts at a lower cost.

The cost of flat-screen TV repair ranges from $42 to $359. You cannot fix a broken screen, but the price of a new flat-panel TV starts from around $249 for a 1080-mp (non-4K) LED TV from LG to as much as $14,999 for an 85-inch 8K LED TV from Samsung. A TV referred to as a “flat TV” or “flat-screen” TV might be any of the following:

LCD TV repair typically costs $60 to $85 for diagnostics testing, and $200 to $300 to perform repairs. LCD TVs use backlighting, which may fail. Newer LCD TVs use LED strips for backlighting. Older ones might use CCFL. If CCFL backlighting fails, a technician can replace it with LED backlighting.

An LED TV is just an LCD TV that uses LED backlighting, which all newer models do (older models use CCFL backlighting). The cost to replace one LED backlighting strip ranges from $100 to $122, including parts and labor.

The cost to replace the motherboard, inverter, or LED"s in a 4K TV ranges from $100 to $275 or more depending on the brand and model. The cost for screen repair for a 4K TV is irrelevant because it cannot be fixed or replaced at a cost that is lower than the cost of a new 4K TV.

Digital light processing (DLP) TVs are also known as projection TVs. DLP big screens have not been made since 2012, and DLP TV repair is usually not worth the cost except for a lamp burnout, in which the bulb can be replaced. The cost to replace bulbs ranges from $60 to $115.

TV repair shops charge an average $60 to $125 per hour, or a flat rate of $50 to $250, which includes the diagnostic fee. Additional costs after that depend on the repairs needed and the brand and type of TV. However, most stores will have a minimum charge of about $90.

Best Buy TV repair is provided through the Geek Squad TV & home theater service. Geek Squad TV repair starts at a base cost of $100 for a diagnostic fee. TV repair is covered under Best Buy’s protection plan, which costs $280 per year when you purchase a TV from Best Buy at the time of purchase, or within the return period printed on your receipt.

The brand and model of your TV will dictate the final repair cost, with more expensive brands and larger TVs costing more to repair. Consider the remaining lifespan of the TV before paying for repairs. You can now buy bigger TVs with more features and better displays for a TV that won’t need repairs for a while and probably comes with a warranty.

The cost of labor to fix a TV ranges from $60 to $125 per hour, or a flat rate of $90 to $299. If the work is performed in your home, the cost ranges from $25 to $125 per hour plus the trip fee. Most TV repairs take 1 to 3 hours if the repair specialist has the parts already.

Some shops will pick up and deliver a TV for free. Others charge a fee that ranges from $40 to $75 for pickup and drop-off, with an average cost of $58.

If you live in a remote area, you may need to ship your TV to a repair facility, costing $99 to $175. Be sure to choose a delivery service that allows you to track the shipment and confirm delivery. When sending your TV into a service center for repair, you will be contacted regarding the associated costs and asked to process payment before the repair is completed, which usually takes two weeks including the shipping time.

Many TV repair shops charge a diagnostic fee that ranges from $20 to $60, depending on whether it is done in your home or the repair shop. Some shops charge a flat fee that ranges from $50 to $250that covers both the diagnostic cost and labor cost. In many cases, the initial diagnostic fee will be applied to the repair cost if you have the shop do the repair.

The more expensive a TV is, the more sense it makes to purchase an additional warranty to defray the potential for costly repairs. Best Buy offers an $89 five-year extended warranty for entry-level TVs. On larger TVs such as the 85-inch Samsung QLED 8K TV, which costs $14,998, the five-year warranty from Geek Squad costs an additional $1,699—11.33% of the cost of the TV.

With modern TVs, repair entails component replacement or replacement of capacitors, for which high levels of certification are not necessary. Generally, TV repair shops will let you know if their employees have certification.

First, check that the connecting cable is securely in the socket on both ends. If that doesn’t work, try substituting another data cable if you have one, or test it with a replacement cable.

Satellite dish repair is either covered by your satellite service company or the cost for a technician to fix it ranges from $80 to $150. Repairs may also be billed at an hourly rate of $50 to $65.

The cost of mounting a TV ranges from $149 to $199, with most people paying around $174 for the labor. The mounting hardware costs between $20 and $500 depending on the brand of mounting hardware and the size of your TV.

There are various ways you might be able to save money on TV repair. These include transporting your TV to a repair shop, using a shop that charges in 15- or 30-minute increments, diagnosing the problem yourself, using salvaged parts, and doing the repair work on your own.

You can also consider the cost of TV repair when purchasing a new TV. More popular TV models are less expensive to repair because repair shops buy parts for the most common TVs in bulk and are therefore able to get them at lower prices.

Plug - If the TV is not powering on and no status LEDs are lighting up, start by plugging the TV into a different outlet. If the TV is too challenging to move, you can run an extension cord from another nearby outlet.

Circuit breaker - Check the circuit breaker for the power outlet that the TV plugs into. You can check the breakers by opening the door to your breaker panel and looking for circuit breakers that are in the OFF position.

Power cable - Check the power cable. If it is a removable cable, you can test it by substituting a power cable from another piece of equipment in your home, or you can buy a replacement cable for this test. The cost for a replacement TV power cable ranges from $2.50 to $10.

Remote control - If the TV is not powering on with the remote control, you should try replacing the batteries. For remote controls with a status LED light, there could be enough power to light the LED but not enough power to send a signal to your TV.

Inverter is bad -It is possible that the inverter, which powers the backlights, has gone bad and needs to be replaced. It’s also possible that one or more capacitors on the inverter have gone bad, in which case a technician may be able to replace capacitors more cheaply than replacing the entire inverter.

Lamp burnout -In a projection TV or older LCD TV, no picture may be caused by lamp burnout. In this case, a technician can replace the bulb quickly and easily.

If the picture is displaying but there are problems such as vertical lines, a double picture, or a white display, this could indicate a faulty motherboard or mainboard.

Plug headphones into the headphone jack. If sound comes from the headphones plugged into the headphone jack, this indicates a problem with the TV speakers.

The primary way to save money on TV repair would be to perform the work yourself. This may require you to purchase and get familiar with various tools such as soldering tools, and methods for replacing a capacitor or some other component.

The right parts - It can be complicated to determine which component of a TV is failing and causing the TV not to work correctly. If you buy a replacement part and perform the repair yourself, the TV may still not work, either because you replaced the wrong part, the part was old and not working properly to begin with, or you did not perform the work correctly. Buying multiple replacement parts can become costly.

Lack of experience – you might cause more damage to the TV due to your lack of knowledge and experience, and you might also end up causing a fire with your soldering iron or being electrocuted.

The cost of repairing a TV could be as much as $500 if multiple repairs are needed. Consumer Reports recommends not to spend more than 50% of the cost of a new TV repairing the old one.

If you have a newer TV that cost thousands of dollars, having it repaired would most likely be cost-effective. If the TV only cost a few hundred dollars to begin with, replacing the TV is more likely to be the best option.

Not included in these prices from Best Buy are 1080P screens, which range from $249 to $279 for 43-inch TVs from brands like Samsung, Sony, and LG. On the upper end, Sony and Samsung both have 95-inch 8K LED TVs for $69,999.

In most cases, a flat-screen TV can be fixed. The exception is a physically damaged display panel or screen. Most other issues including failing speakers, backlights, or power supply. Burned out fuses and damaged input ports can also be repaired.

If the screen is not physically damaged but is not showing a picture or is displaying “snow’” or vertical or horizontal lines, a technician can repair the TV by replacing failed components. If the screen is physically damaged, it cannot be repaired.

You cannot replace a broken flat-screen display. New TVs costs anywhere from $249 for a 1080P (non 4K) LED TV from LG to as much as $14,999 for an 85” 8K LED TV from Samsung.

Some shops will pick up and deliver a TV for free. Others charge a fee that ranges from $40 to $75 for pickup and drop-off, with an average cost of $58.

If you live in a remote area, you may need to ship your TV to a repair facility, costing $99 to $175. Be sure to choose a delivery service that allows you to track the shipment and confirm delivery.

Use our “Get an Estimate” tool to review potential costs if you get service directly from Apple. The prices shown here are only for screen repair. If your iPhone needs other service, you’ll pay additional costs.

If you go to another service provider, they can set their own fees, so ask them for an estimate. For service covered by AppleCare+, your fee per incident will be the same regardless of which service provider you choose.

Your country or region offers AppleCare+ for this product. Screen repair (front) is eligible for coverage with a fee by using an incident of accidental damage from handling that comes with your AppleCare+ plan.

The Apple Limited Warranty covers your iPhone and the Apple-branded accessories that come in the box with your product against manufacturing issues for one year from the date you bought them. Apple-branded accessories purchased separately are covered by the Apple Limited Warranty for Accessories. This includes adapters, spare cables, wireless chargers, or cases.

Depending on the issue, you might also have coverage with AppleCare+. Terms and Conditions apply, including fees. Feature availability and options may vary by country or region.

We guarantee our service, including replacement parts, for 90 days or the remaining term of your Apple warranty or AppleCare plan, whichever is longer. This is in addition to your rights provided by consumer law.

Replacement equipment that Apple provides as part of the repair or replacement service may contain new or previously used genuine Apple parts that have been tested and pass Apple functional requirements.

As often as you use your smartphone, it’s almost inevitable that you’ll eventually drop it. You may be extremely careful, but it only takes one fumble for your phone to tumble. While iPhone screens are designed to withstand impact, you might still end up with a shattered screen.

The good news: a broken screen doesn’t mean your phone is kaput. In fact, if only the glass is broken, the fix is quick and inexpensive. The bad news: if the LCD screen is broken, you’re looking at a pricier repair.

If you’ve looked into replacement parts, you’ve likely come across two very different options: a glass screen, and an LCD screen. While the first option is cheap, the second is definitely not. Here’s the difference:

1. The glass screen is the exterior layer on your phone’s display. While it is specially engineered for durability, it’s still just glass (between layers of plastic film), which is why it’s not very pricey to replace.

Most of the time, the damage to your screen will be pretty obvious. You’ll see the spider web patterns of shattered glass across the front of your iPhone. Occasionally, however, the glass screen will be intact, and you might not realize the damage until you try to use it. Whether the damage is visible or not, it’s a good idea to run a quick diagnostic to determine the extent of it.

If you encounter any of these problems, you’re dealing with a broken LCD screen. If the glass is shattered, but the display is clear and touch capability is working, that’s a good sign. The problem is probably just the glass screen.

Whether you’re dealing with cracked glass or a broken LCD screen, you can find a quick, reliable repair service at FastPhoneRepair.com. Our qualified technicians will get your iPhone repaired and up and running again in record time and at reasonable rates.

I"m just wondering, would it be cheaper to go a 3rd party to fix it? How much will it cost approximately? Will Apple be cheaper given the limited availability of the screen assembly? Can the LCD be replaced alone? The main answer I"m looking for is how much this is gonna cost me. I doubt they"re going to cover it under warranty, even though I have no idea what caused it.

Edit: For anyone thinking of helping, firstly thanks. Secondly, one of my friends had their screen replaced by apple, a late 2015 15 inch Pro model. This cost them £332, just as a guide for when deciding how much it will cost for my model. Thanks again.

I just bought a 70 inc skyworth smart tv two weeks ago and already cracked the screen. The top half of the screen is lined but the bottom is perfect. The crack is in the upper right hand side in the corner. Any idea of what I may need to replace just by what I have told you so far? Any help is appreciated. Thank you

Hi my son threw something at my 65 inch tv and now it has lines from top to bottom I can still see a picture on both sides of the tv it just black in one stop with the lines. Can you help me please.

Hello, My son threw a plastic toy at my tv it hit the bottom now I have a small white circle with a few short lines coming from it at the bottom of my tv, my screen is now black with no picture at all but I can still hear ok, What would I need to have repaired to bring back my picture.

80″ SHARP AQUOS QUATTRON 3D L serial#206819501 hit screen by mistake and I’m told it’s a broken screen, having trouble finding someone to fix it! Help!!! trying not to throw it away!

I have a Samsung 60 inch flat screen model##LN46B65068F S/N# AUHR3CP5400327N it was working then all of a sudden it got a line straight across the middle of the screen and then there was no picture can u tell me why and what might be wrong with it please and thank you

Gm I have a proscan plcd3717A tv. It comes on for a while and shut off. 37 LCD tv at school tuner. S/n a1212089790001040. I changed the power supply board. But still doing the same thing. Should I change the main board then.

Hi my 40inch LCD TV comes on on standby then I press the button and the light turns blue. There is no pic or lights on the screen and also no sound. Model no,m40/57g-GB-ftcu-UK. Product code ,um40d57bftcug107, serial no, 105571 03650. Thanks

I was watching a show and i accidentally threw my phone at my tv and now there’s lines on the screen but the screen isn’t cracked. Can anyone help me out?

I have a Sony Bravia KDL-50W800B with a cracked screen. I understand LG makes these screens but I cannot locate a replacement. Does anyone know where I can get a new screen.

I have a SamsungLN46C 650. Over the last year the HDMI ports have loosened & caused vert lines. I corrected this by slightly adjusting them each one eventually quit working. Now none work so i have no signal. I want to solder these back and have experience soldering. The tv is 6 years old. Good idea to try to repair this myself?

I just bought a 60′ Sony tv and I accidentally hit the screen while trying to attempt to move it, the screen shattered and it’s not covered under the warranty. Can anyone fix it?

Oh no. My husband just forked out $600 on a new TV and we were all so excited. We’ve had it for 2 weeks but my son with autism just threw something at the TV while having a tantrum and now we only see half the screen and it looks all cracked. Devastated. We will try to be creative and fix it.

No picture or tv stations nor will it let even noise come through when I change the source by stepping through it, I tried to look at the screen for letters, but do not see any.

I bought a lg 50LN5100-ub a few years ago. My son threw a soft toy at it and it looks like the outside screen is busted but it’s not it’s all on the inside. I was wondering if i could send you a picture of it and tell me what it might be so I can fix it. I was doing some research and it says that it’s probably the t-con board but I want to get another opinion before I buy one.

Yes a 24 inch Vizio that has a busted screen should simply be replaced…. sell it on an online classified website and maybe you can get some money for the other parts that are still working.

I have an Emerson LF501EM5F 50″ Class 1080p LED HDTV and am looking for a screen replacement for it. It is the front screen that needs to be replaced and I can not find one any where. Does anyone know where I can get on and about how much they are.

I have the exact same problem with my Samsung 60 inch UN60J6200AFXZA set which is barely 6 months old. It took a slight bump to the front screen, didn’t leave any visible damage to the outside, but supposedly cracked the internal portion causing vertical colored lines and missing images.

I transported my 43 inch vizio flat screen TV and now I have no picture and I faint line running a curvy diagonal across the screen. It also has some blue and red colors by the line. TV was wrapped in blankets while transported. Model # E43-X2 Serial # LWZ2SEAR0510795

I have a 55 inch samsung smart tv , going thru setup the picture is fine . When changing to all inputs the right side of the screen has a great pic but no color. I’ve changed the Tcon board , same picture . The picture is great just black and white picture on the right side of screen . Any advice would be appreciated .

I accidentally hit my 60 inch TV today and it looks like the internal screen is broken, no damage to the outside at all, I have vertical lines on half the screen and the broken glass effect in the corner, if I was to buy a repair kit from amazon or ebay, will this work? I’m pretty sure this wouldn’t be covered under the manufacturer’s warranty.

I have complained service center they told me its power supply has problem and they replace it, after taking it to my house next day it has same problem.

I have a Sony KDL-32BX310, has no picture or sound. Power light turns from red to green when powered up (no flash codes). Screen shows dim backlight, goes off for about 2 seconds then back on to the dim backlight. I have tried several audio and video inputs. No on screen menus showing. I checked several power inputs from supply to main board, several showing, tough with no schematic. Changed the main board with a used part (supposed to be good??), thinking this is the only component that could prevent audio and video. Possible power supply? I checked your site for boards for this TV and not available at this time. I read the eprom has to be flashed