2.4 tft lcd pinout factory

A 2.4” TFT LCD module consists of a bright backlight (4 white LEDs) and a colourful 240X320 pixels display. It also features individual RGB pixel control giving a much better resolution than the black and white displays. A resistive touch screen comes pre-installed with the module as a bonus and hence you can easily detect your finger presses anywhere on the screen.

The TFT comes with an auto-reset circuit which gets active on every breakout. However, a user can reset the module using this pin also, in case setup is not resetting clean.

The TFT comes with an auto-reset circuit which gets active on every breakout. However, a user can reset the module using this pin also, in case setup is not resetting clean.

Resistive Touch Pins – Y+, X+, Y-, and X- are the 4 resistive touch pins which require analog pins to read and determine touch pins. Their overlay is fixed at the top of the module which makes them electrically separate from the TFT. They can be used is 8-bit as well as SPI mode.

The 2.4” TFT LCD module supports many modes. However, two of them are very popular among users – “SPI mode” and “8-bit mode”. The display contains pins on both sides required for a mode and a user can switch easily between them by simply rewiring the display. It should be noted that only one mode can be used at a time.

A 2.4” TFT module has a very flexible usage. It is compatible with all your DIY projects where you want to add a bright, colourful, and touchscreen enabled display.

2.4” TFT LCD Module is one of the most common RGB color display modules. Therefore,  this module offer different applications from conventional display modules in features and usage. It offers multi-way communication protocols to the developers/designers. This TFT module is not popular only because of its color screen, it has a resistive touch on itself. The touch screen is accessible by microcontrollers and they are controllable by the users according to the requirements.  Additionally, it can display up to 240×320 pixels on a single screen. Even images can also show on the screen. It is mostly available in developing projects and low-cost devices only.

The pin configuration of the module is simple like other display devices. The only problem is the developers need to understand first which method is better to operate the TFT LCD display. Therefore, the TFT touch screen uses the diver to operate each pixel and the driver uses a small no of pins as input and makes it user friendly. The pin configuration is as follows:

These all pins from D0~D7 are the digital data input pins. It requires only when a developer needs to work with LCD using 8-bit data or using Assemble language. The Arduino library mostly uses the SPI pins.

The LCD screen is made up of three types of pixels at a single point. The LCD uses the two polarized layers to pass the layer but both layers are opposite in pattern to each other. The liquid crystals relate to anode and cathode which makes the liquid crystal change their angle which helps to change the angle of light. The change in angle allows the light to pass from the polarized layers. There is always a total combination of three colors of pixels which are known as RGB. The intensity of pixels is controllable and helps to manage each pixel. The change in intensity changes the angle of the crystals and which makes the output light according to the image or text requirement.

Each pixel in the LCD needs to control according to the requirement individually. There are a driver ILI9341 which can control each pixel with the small no of pins which we already discussed above. In LCD the driver also attached to the Arduino shield. The Arduino shield comes with simple input pins but the driver output pins which are the most important pin. These pins are the source and gate driver pins. The source pins are 720pin and the gate pins are 320pins. The driver has an internal GRAM that stores the data each time the microcontroller send to it. The data on the display screen always temporary and stay in the GRAM until it needs to show to the screen. The following block diagram shows the internal structure of the driver ILI9341:

The LCD is useable with Arduino but it depends on the library. The library is compatible with Arduino only and compatible with the attached shield. To use the library first attach the LCD on the Arduino UNO or attach it by connecting wires on the other Arduino. Here’s the Arduino Uno with TFT shield:

The above libraries will help but to use the LCD first describe the LCD pins attached to the Arduino. It is changeable with the requirement of the LCD use. There are other libraries which can perform different functions which the above library unable to perform. There is some no of pins that need to describe.

The initialize the LCD in the Arduino setup. To initialize the LCD always remember it could give some errors. To avoid errors, use the reset commands.

The following command will make the whole screen black because the use of white color on the screen won’t show the data on the screen. So always define the screen fill color to describe the screen. The usage of the image is only most of the time with images and text. Every function on the LCD needs to change from the display command only but the rest of the data will be the same on the LCD. The internal SD card solves the memory issue.

Voltage type: 5v or 3v voltage input voltage，input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.

Winstar WF24H is a 2.4 inch diagonal full color 240x320 TFT display module. This 2.4 inch TFT LCD display is built in with ILI9341V IC; it supports 8/16-bit 8080-series Parallel MCU Interface. WF24H model is having module dimension of 42.72 x 60.26 mm and Active area size of 36.72 x 48.96 mm; it integrated ILI9341V controller on module, logic supply voltage range from 2.4V to 3.3V.

This 2.4" TFT LCD module is portrait mode, if you would like to use landscape mode please contact with us for more technical support. This 2.4" TFT Display is featured with brightness up to 500 cd/m2(typical value), it can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃. It is very suitable for smart home applications, medical devices, portable devices, wearable devices, energy controls, telecoms and data transfers etc.

Search keyword: tft 2.4, tft 2.4", 2.4 tft lcd, 2.4" tft lcd, 2.4 inch tft lcd, tft lcd 2.4, 2.4 tft display, 2.4" tft display, 2.4 inch tft display, tft display 2.4, tft display 2.4"

Hello, I have a few 2.4" touch screens used to be connected to verious Adruino boards. A little search I found taht they could be used on Pi as well. The trouble is I don"t know which pin on the display goes to which Pi"s GPIO. Whould be nice to have a diagram or chart to indicate that. does anyone knows a goo linke for that? Thanks.

ER-TFT024-3 is 240x320 dots 2.4" color tft lcd module display with ILI9341 controller and optional 4-wire resistive touch panel and capacitive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit,18-bit parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 2.4"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

You may wish to have NEWHAVEN NHD-2.4-240320,our part number ER-TFT024-4 should meet this requirment that is the completely the same withNEWHAVEN NHD-2.4-240320.

ER-TFT024-4 is still not our general product ,we don"t have enough stock .You have to email ([email protected]) our sales to buy samples or orders. Besides the minimum order quantity is no less than 500pcs per order.The production lead time is 5-6 weeks.

ER-TFT024IPS-3 is 240x320 Pixels IPS 2.4" color tft lcd display with ST7789V controller and optional 4-wire resistive touch panel and capacitive touch panel,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit,18-bit parallel,3-wire,4-wire serial spi RGB interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 2.4"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

This 240x320 resolution LCD TFT is a standard display with 8-bit/16-bit Parallel interface, offering 262K colors and a 6:00 optimal view. This Liquid Crystal Display has a built-in ST7789Vi controller, FFC ZIF I/O connection, is RoHS compliant and does not come with a touchscreen.

Adjust the length, position, and pinout of your cables or add additional connectors. Get a cable solution that’s precisely designed to make your connections streamlined and secure.

NHD-2.4-240320CF-CTXI#-FT | 2.4" Standard LCD | 240x320 Pixels | Resistive Touchscreen | Hot-bar Soldering Connection | Screen Printed Icons on Touch Panel | Discontinued EOL Product

This 240x320 resolution LCD TFT is a standard display with 8-bit/16-bit Parallel interface, offering 262K colors, 2.8V power supply, and a 12:00 optimal view. This Liquid Crystal Display has a built-in ILI9341 controller, hot-bar solder connection, has a 4-wire resistive touchscreen and screen printed icons featured on the touch panel. The display is RoHS compliant and has been discontinued. Purchase now while stock is still available!

Adjust the length, position, and pinout of your cables or add additional connectors. Get a cable solution that’s precisely designed to make your connections streamlined and secure.

GD24TWD-GTT24P123 VER:3.00 Color Digital TFT LCD Module is comprised by driver board GD24TWD VER:3.00 and TFT LCD Display GTT24P123. The LCD module supports CVBS signal input, NTSC and PAL formats which two formats applies to auto identification.

GD24TWD-GTT24P123 VER:3.00 Color Digital TFT LCD Module is comprised by driver board GD24TWD VER:3.00 and TFT LCD Display GTT24P123. The LCD module supports CVBS signal input, NTSC and PAL formats which two formats applies to auto identification. Button adjustment with OSD menu control. It is mainly used for video phones and other display electronic devices

{"specs":[],"skus":[{"id":4696,"useViewType":false,"productId":282,"templateId":1,"code":"","name":"2.4 inch TFT LCD display module with drive board, GD24TWD-GTT24P123","stock":0,"price":0.00,"retailPrice":0.00,"weight":0.00,"status":"1","isDefault":"1","createDate":"2022-03-08 11:33:19","updateDate":"2022-03-08 11:33:19","productSkuSpecs":[],"moq":1,"skuId":0,"chargedWeight":0.00}],"specConfs":[]}

FormikeGroup was founded in 1999, which engaged in R&D, design, manufactureand sales of LCD display solution, Wi-Fi / Bluetooth Module, Smart Watch as well asaccessories of cell phone.

Ourexperienced technical on OEM and ODM and managerial personnel, strict qualitymanagement system, competitive prices ensure that we always be at the forefrontof LCD, Wifi Module, Smart Watch and accessories of cell phone industry.

Kingtech is one of the leading TFT LCD display OEM/ODM manufacturers in China since 2003. Customization is allowed for projects such as industrial devices, medical, POS, logistics devices, smart home applications and etc.

To provide a one-stop LCD display solution. During the last 17 years, based on LCD manufacturing as our center, we gradually expand to the TFT capacitive touchscreen, driving board, software hardware design, and complete industrial computer solution.

As a professional LCD screen supplier/ LCD display supplier/ LCD panel company/ LCD module manufacturer, Kingtech LCD aims to provide a one-stop service and solve your problems. With a strong LCD Display module R & D team and strict quality management of IS09001, IS01400ATF16949 certificates.