rpi 3.2 inch tft lcd screen quotation

This is all-new Version V4.0 3.2 Inch TFT LCD Touch Screen for Raspberry Pi display from waveshare is big (3.2 diagonal) bright and colourful! 240320 pixels with individual RGB pixel control, this has way more resolution than a black and white 12864 display.

As a bonus, this3.2 Inch TFT LCD Screen for Raspberry Pi V4.0 display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.This display has a controller built into it with RAM buffering so that almost no work is done by the microcontroller.

This3.2 Inch TFT LCD Screen display is an alternative solution for Raspberry Pi compatible HDMI display; the 3.2 inches Resistive TFT Touch Screen Display, which uses SPI Protocol (serial peripheral interface) to communicate with the main processor. It can be mounted directly to the GPIO pins and it doesnt require any external power source.

In here we have a detailed explanation on how to install LCD drivers in a custom Raspbian image. The standard version of Raspbian does not include drivers for LCD touchscreens, so we will have to install and configure them manually.

3.2 Inch Resistive Touch Screen TFT LCD For Raspberry PI is an ideal alternative solution for HDMI monitor. It supports any revision of Raspberry Pi and it can be directly plugged on to the RPi board, combined with the portable power this module is a convenient Men-Machine interface for Raspberry Pi.

Designed for use with the Raspberry Pi Model B/B+, the Seeed 3.2 inch TFT LCD Touch Screen is an easy way to process photos and videos. Easily navigate the touchscreen interface to take photos with up to 17 camera modes, and play videos with a variety of format—MP4 included Read More

Why the LCD doesn"t work with my Raspbian?To use the LCD with the Raspberry Pi official image, driver should be installed first. Please refer to the user manual.

However, for the first testing, you may want to use our provided image directly.Why the LCD still doesn"t work with the Waveshare provided image?Make sure the hardware connection is correct and connects fine.

The PWR will keep on and the ACT will keep blinking when the Raspberry Pi starts up successfully, in case both of the two LEDs keep on, it is possible that the image was burnt incorrectly OR the TF card was in bad contact.Which power supply should I use?It is strongly recommended to use a stand-alone 5V/2A power adapter, because the PC"s USB port might have not enough power to support the Pi and LCD.

"Features Designed for Raspberry Pi, easy to use Supports any revision of Raspberry Pi (directly-pluggable) Driver provided (works with custom Raspbian directly) Supports Raspbian system, enables your system to: Play videos (supports multi formats, MP4 and so on) Take photos by touching (up to 17 camera modes) Support software keyboard (system interaction without keyboard/mouse) High quality immersion gold surface plating Key Parameters LCD Type TFT LCD Interface SPI Touch Screen Type Resistive Touch Screen Controller XPT2046 Colors 65536 Backlight LED Resolution 320*240 (Pixel) Aspect Ratio 4:3 Power Consumption TBD Backlight Current TBD Operating Temp. (?) TBD Interface PIN NO. SYMBOL DESCRIPTION 1, 17 3.3V Power positive (3.3V power input) 2, 4 5V Power positive (5V power input) 3, 5, 7, 8, 10, 22 NC NC 6, 9, 14, 20, 25 GND Ground 11 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching 12 KEY1 Key 13 RST Reset 15 LCD_RS LCD instruction control, Instruction/Data Register selection 16 KEY2 Key 18 KEY3 Key 19 LCD_SI / TP_SI SPI data input of LCD/Touch Panel 21 TP_SO SPI data output of Touch Panel 23 LCD_SCK / TP_SCK SPI clock of LCD/Touch Panel 24 LCD_CS LCD chip selection, low active 26 TP_CS Touch Panel chip selection, low active "

NMLCD-32QAis a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with a Resistive Touch Panel (RTP). The module display area contains 240 x 320 pixels. This product accords with RoHS environmental criterion.

Shenzhen SLS Industrial Co.,ltd established in 2003, is a professional LCD module manufacturer and solution provider. We have 1 full-auto COG assembly line, 2 semi-auto assembly line, backlight assembly line, no dust TP bonding line and manufacturing tech support, we can provide unique, innovative and cost effective LCD module development and manufacturing. Our product range includes: middle-small size TFT LCD, industrial capacitive touch panel... Our LCD products have been widely used in communications, GPS, Equipment, electronic audio-visual, instrumentation, household appliances, PDA and other industries.