brother printer lcd display not working free sample

Verify the power cord is connected to the back of the machine and the AC power outlet. If the power cord is connected to a surge protector or power switch, remove the cord from the device and connect it directly to the outlet. This is for testing purposes. Removing the device assists in determining if the issue is related to the device or the Brother machine.

Verify the machine is powered ON. The Brother machine has an ON/OFF button located on control panel of the machine. If machine is OFF, the display will be blank.

If the display is still blank, try to tilt or move up or down the LCD display and also try a different known working electrical outlet at your location.

4. When the screen is blank but power LED light is on, this is a sign the firmware has been corrupted. This can happen if power or network connection is interrupted before the end of the firmware update. The firmware can be recovered provided the printer is connected to a computer via printer USB cable and the computer shows the printer is connected.

- If the display doesn"t respond but you can hear your machine functioning, your machine will require service. Your machine has a one-year limited exchange warranty. You may use the link below to find a Brother-authorized service center in your area. You may also contact Customer Support for additional warranty options.

2. Verify the Brother machine"s power switch is in the ON position. The machine has an ON/OFF switch located on the right side of the Brother machine.

When the small circle ( o ) on the switch is pressed, the Brother machine will be OFF. When the small dash ( - ) on the switch is pressed, the Brother machine will be ON.

3. Verify the power cord is connected to the back of the Brother machine and directly to the AC power outlet. If the power cord is connected to a surge protector or power switch, unplug the cord from the device and plug it directly into the outlet. Removing the device assists in determining if the issue (blank display) is related to the device or the Brother machine.

6. Verify the outlet is working by plugging a device (a working lamp, radio etc.) directly into the same outlet. If that device does not work, the problem is related to the outlet or circuit. You may also need to check for a tripped circuit breaker. If a wall switch controls the outlet verify that the switch is ON. Another test would be to connect the Brother machine to a completely different outlet.

My LCD screen is shown blank without any single word display on the screen, it still can print if the printer network can be set to proper wifi id. But, in this case the LCD screen is blank and showing nothing, so i can not set to any wifi id at all.

Error 30 is one of the most common Brother printer error messages. The error code 30 and the error message “Unable to Print” indicate that the printer is not able to print due to a mechanical malfunction. Another possible reason for this error to occur is an object getting stuck in the machine, for example a paper clip or a piece of paper.

If your Brother printer is not printing and the message “Unable to Print 30” appears, fix the problem with the following steps for troubleshooting: Use both hands to lift the scanner cover into open position and make sure that you see the scanner cover support arm on the left hand side of the machine.

Now check both the right and the left corner and remove any objects, such as paper scraps or paper clips, that are jammed in the machine. Afterwards, turn the printer around and open the jam clear cover on the back to check for foreign objects or to remove jammed paper. Once all objects have been removed, close the covers and resume the printing job.

Are you looking for a solution to get rid of error 51? The error message “Unable to Print 51” is a common Brother printer error, indicating that there is a problem with the laser unit.

If you have recently changed the cartridge of your Brother printer, it is highly probable that either the cartridge, the laser, or the lid was not put into proper position. To fix the issue, open the printer up again and make sure that everything is installed properly.

If you have not changed the cartridge and are still facing error code 51, try switching the printer off and back on again. If the problem persists, part of the laser unit may be defective. You can fix the issue by replacing the laser unit.

Brother error 50 indicates a malfunction of the fuser unit. This could be caused by the fuser unit getting too hot during printing, or not heating up enough in order to print. As a result, the printer is unable to print.

To fix the issue, turn the printer off and wait for five to ten minutes. Then turn the printer on again and wait for another ten minutes. If error 50 persists, you may need to replace the fuser unit of your Brother printer.

Are you looking for a solution to get rid of error 51? The error message “Unable to Print 51” is a common Brother printer error, indicating that there is a problem with the laser unit.

If you have recently changed the cartridge of your Brother printer, it is highly probable that either the cartridge, the laser, or the lid was not put into proper position. To fix the issue, open the printer up again and make sure that everything is installed properly.

If you have not changed the cartridge and are still facing error code 51, try switching the printer off and back on again. If the problem persists, part of the laser unit may be defective. You can fix the issue by replacing the laser unit.

Error 48 is one of many “Unable to Print” error codes generated by Brother printers. The error message means that the print head cable or circuit board is either broken or damaged. This may be caused by foreign objects, such as ripped pieces of paper, or paper clips getting stuck in the printer and thus destructing the printer head.

To fix Brother printer error 48, turn the printer off and lift the scanner cover. Then look for any objects stuck in the machine. If you see any objects that do not belong, make sure to remove them carefully. If this does not help you get rid of the error message, you may need to clean off the encoder strip of your brother printer.

The encoder strip is a transparent plastic strip in front of the vinyl band within the machine. Using a dry cloth, clean the strip carefully. Then turn on the printer and pass a print command to check if the problem was solved.

If the error TS-02 occurs while using your Brother printer, you are facing one of the most common Brother printer errors. The error code TS-02 occurs when the wireless access point or router fails to connect to the MAC address of the printer. There are several possible causes of Brother error TS-02: Windows system file damage, corrupted system file entries, incomplete installation of the Brother printer, or other hardware problems.

If the error message “Replace Toner” appears on the display of your Brother printer, the toner cartridge of your printer is at its end of life and needs to be replaced shortly.

The easiest way to get rid of the error message is to replace the toner of your Brother printer. If the error “Replace Toner” does not clear from the display after the replacement, try these quick fix solutions:

First, make sure that the new toner cartridge is installed properly. Second, confirm that you have installed a brand new Brother Standard toner cartridge. If you are using a Brother starter toner, a remanufactured toner or a non-Brother toner, this is what causes the error.

Also make sure that the toner displayed on the LCD is the same color as the toner you already replaced. If it is not the same one, simply replace the one shown in the display in order to get rid of the “Replace Toner” error.

The error message “No Paper” on the display of your Brother printer indicates that the machine is out of paper. However, the error message may persist even after refilling the paper tray. To fix the issue, you need to identify the cause of the error.

Ensure that the paper is loaded correctly in the paper tray, and that the paper source is selected correctly in your application or printer driver. If “No Paper” still appears on the display, try printing a document by using the manual feed slot of your Brother printer by changing the tray settings. If you are able to print a document, the error message should no longer appear.

However, if the error persists, continue by adjusting the paper type and paper size setting on your printer. You can also check the printer settings reports or use the Auto Detect function to fix the problem.

The Drum Error is another common error experienced by users of Brother printers. Both the error message “Drum Error” and “Clean Drum Unit” mean that the drum unit of your machine is dirty. The dirt may be caused by dust or by loose toner.

As a quick fix solution, you need to remove the toner unit and clean the corona wires in the drum unit. After removing the toner from your Brother printer, slide the blue tab at the front of the unit from side by side, then return it to its standard position and put the drum unit back into the machine. If cleaning the drum unit does not solve the problem, and the printer continues to show a drum error, replace the drum unit with a new one.

In most cases, error messages 20, 21, 22 and 23 can be easily get rid of by simply turning the printer off and back on again. However, if you are still facing one of the error messages, make sure that the ink cartridge is loaded correctly. If the cartridge is broken, replace it with a new one. If the ink sensor is defective, replace the main PCB of your Brother printer.

Have you come across error code TS-07 while working with your Brother printer? Then you are facing a problem with the connection of your printer to the WLAN access point or router. Luckily, this problem can usually be solved easily.

Get rid of Brother printer error TS-07, follow these simple troubleshooting steps: Ensure that your WLAN access point or router is supporting WPS or AOSS. Then check the settings of your Brother printer by using automatic wireless mode with either WPS or AOSS.

The Brother printer error code 36 appears on the display of the printer when there is a mechanical malfunction. Here is how to solve the issue causing the error message “Print Unable 36”: Turn off your Brother printer, then turn it back on again. Check the display for any errors. If there are no more error messages, continue with the next step.

Print the user settings list by entering the menu, then choose “machine info” – “user settings” and press “start”. If the list is printed and error 36 does not show up on the display, you have successfully solved the problem.

If the error message persists, turn off your printer and remove both the drum and the toner. Turn the printer back on and check if the error appears. If not, reinstall both drum and toner, and print the user settings list as described in step two.

Error 45 is a common Brother printer error code. It occurs when the Windows system is not able to acknowledge the device and thinks that the printer is disconnected. This error is most commonly caused by a temporary system file malfunction or by a problem with the registry system files within Windows.

To fix Brother printer error code 45, try to reconnect the printer to your computer. In order to do this, unplug the USB cable of the device, then plug it back into the computer. In some cases, reconnecting the Brother printer to the computer will already solve the problem.

Another solution is to use a driver assist program to fix the Windows registry files. The program can restore any files that are damages and possibly causing error 45.

The common Brother printer error code 0x803c010b looks more complicated than it actually is. The error simply indicates that your printer is not connected to the network via a wired or wireless connection. The error code is often accompanied by the message “Unable to print the documents. Please try later.”

To fix Brother error code 0x803c010b, there are two common solutions: In the control panel of your Windows computer, access the printer menu. In the settings for the Standard TCP / IP Port, select “Configure Port”, then unmark the “SNMP Status Enabled” checkbox. By applying the new setting, you disable the protocol. After rebooting your computer, check if the connection to the printer is now established.

In some cases, a reinstallation of the printer device fixes error 45. In the control panel, select the “Devices and Printers” option and remove your Brother printer. Now unplug your printer and restart your computer. After the restart, plug in your Printer and reinstall its drivers.

When the main motor of the Brother printer is not functioning properly, error code 54 is shown in the display of the device. The main motor is responsible for driving the main gear train and therefore an important part of the printing process.

If you are facing Brother printer error code 54, switch your printer off and back on again. In many cases, a restart of the printer already fixes the problem. Another possible solution is to remove the toner before turning the printer back on.

If the motor is working without the toner installed, the problem may in fact be caused by the toner. In this case, simply replace the toner. If the main motor is still not working, replace the motor with a new one.

Error code 55 and the error message “Replace Laser Unit” are common for Brother printers. The error code appears on the display when the laser unit has reached the end of its life cycle. It is necessary to replace the laser unit every once in a while, because worn laser units will lead to a poor printing quality.

The Brother printer error message “Paper Jam” means exactly what it says: The printer has detected a paper jam in the machine. However, in some cases the error persists even after the jammed paper has been removed. Here is what you can do to solve the problem.

First, pull the paper tray out of the printer and check for any paper stuck in the cavity where the paper tray was installed. Remove any paper stuck in the machine. Next, turn off the printer and remove the rear cover from the back of your Brother printer. If there is any paper stuck in this area, slowly pull out the paper. Also check the are under the flatbed scanner and remove any stuck paper carefully.

If you are still facing the Brother printer error “Paper Jam”, even though there is no paper stuck in the machine, the rubber feeder rollers may require cleaning. Carefully open the carriage and wipe the rollers with a soft cloth. Another way to get rid of the error message is to turn the printer off and then on again, or to open and close the scanner cover. If the paper jam has been removed successfully, this should solve the problem. If not, check again for any small pieces of ripped paper in the machine.

Printers are the perfect finish for a home office, allowing users the convenience and ease of use without having to travel or pay to print documents or photos. Owning a printer has countless benefits, though, like any other technology, printers have a few minor caveats. However, don’t be dismayed because many common printer problems have easy solutions!

If you are in the market for a printer, then you might be surprised by how many different types of printers there are. Deciding which printer is the right one for you is simple. Are you mostly printing photos and need a good quality printer? You will want an Inkjet printer, which prints slower than other models, but prints high-quality photos. If you print at a high volume and aren’t printing photos then a LED or laserjet printer is what you want. The LED and laserjet printers don’t use ink, like an Inkjet, instead, they use toner which allows users to print high-quality documents quickly. Another thing to consider is whether you need to scan and fax documents in addition to printing. You will want to purchase an All-In-One printer if that is the case. For a more detailed look at what type of printer you should purchase go *here* (link to another more in-depth article to be added later)

Printers can range anywhere from $100 to $1000, however, you don’t have to spend hundreds of dollars to own a high-quality printer. It is important to keep in mind that the printer will continue to cost you money after you have purchased it since you will need to purchase replacement ink. Many companies sell their printers at a low price but sell their replacement toner cartridges at a very steep price. For example, a Brother Monochrome Laser Printer HL-L2320D sells for $120. Cheap right? Until you need to replace your toner and drum unit, which sells for $75 and $45. One option is to purchase the less expensive printer, like the Brother Monochrome printer and then purchase Ink Toner Store’s generic brand toner cartridges which are much cheaper. The toner that sells for $75 is now only $17.95! Another option is to purchase a slightly more expensive printer, like an Inkjet printer. The Brother Inkjet MFC-J6520DW sells for $229.99, but the ink is much more affordable at $22.99.

Every printer is different from the model to the brand. It is important to correctly identify what type of printer is being used. All printers can have the same problems, but different printers will have different solutions.  For example, a paper jam is a common problem that occurs with all printers. How a paper jam is fixed will depend on the printer.

Printer message errors are completely unreliable. You can swap out an old toner with a brand new one and the printer will still insist it needs a new ink cartridge. Unless the cartridge itself is somehow damaged or broken, then resetting your printer should easily fix this problem. A hard reset consists of a couple steps that are typically really easy to follow. All you need to do is search on your computer for the reset instructions for your specific printer model. Depending on what model printer you use, there may also be a video guide that shows how to do to reset. If you still have trouble figuring out how to reset your printer, you can call us at 888-720-7888 and we will be happy to assist you.

Usually, when you buy a printer, it comes with a toner and drum unit already inside it (if it uses them). So no, you wouldn’t have to buy them when you initially purchase the printer. However, these cartridges are usually not filled all the way and you will need to have them replaced at some point in the future. The toner and the drum are two individual parts that require assembly after purchase. Don’t worry, though, putting them together is very simple. Once the cover on the toner is removed, you simply slide it into the drum unit and then put the entire bundle into the printer.

If your printer is printing too slow it could be because of many different reasons. It depends on what type of printer model you have because some printers print at a much slower speed in order to produce high-quality prints. Other printer models print much faster, but the quality is low. You may need to change the Print Quality in the printer settings. If you need to print everyday documents the Print Quality should be set to the Fast Draft setting. Go into the Print and Properties and find where to change the quality of the print job. If you can’t find how to change this for your printer then you can search for instructions for your specific printer model.

The first thing you should do is search for instructions pertaining to your specific printer model on how to handle a paper jam. Typically, this is an easy fix. You’ll need to open your printer, take out the toner and drum and gently pull the paper out. Don’t pull too hard as you don’t want to damage the printer. Sometimes a paper jam is caused by only a tiny piece of paper which can be hard to reach. You will want a pair of long tweezers to pull it out. If you are still having trouble, you may want to call a printer technician to assist you. As always, you can also call us and we will help you the best we can!

The quality of the print job depends not only on the printer itself but on the ink or toner cartridge and the drum unit if there is one. The type of paper also influences the print quality, so make sure you have the right type of paper for the type of printing that is being done. If the paper is not an issue, the toner may be the culprit. First, take the toner out and gently rock it from side to side. Don’t shake the toner and be careful not to touch the toner roll because it can leave fingerprints. If you don’t print frequently, sometimes the toner settles and needs to be “activated.” If your printer uses ink instead of toner, it is possible that the ink has dried and needs to be replaced.

The reason an extra sheet of paper is being printed is because of the print settings. This setting is typically used in offices where the print volume is high and there are multiple users printing. The extra sheet of paper prints out to separate print jobs, but if you are the only one printing this can be really annoying. Thankfully, it is an easy fix! Go to your printer and devices on your computer, click on your printer and then click on printer preferences. You should be able to deselect the separator pages from there.

If you have more than one printer, an issue that occurs is that the wrong printer is printing. This is a random glitch, but can easily be fixed. You will want to go to  your Devices and Printers folder and right click on the printer that you want. You will have the option to make it your default printer. Depending on your computer, these steps may be different but are generally the same.

Some issues have the most obvious of fixes. Make sure the printer is plugged in, turned on and ready to print. If there are any error lights blinking, check the printer manual or online to see what the error means. Another option is to try printing an internal test page. If the internal test page does not print out then try turning the printer off and on, taking the toner cartridges out and reinserting them and then try printing the test page one more time.

If you have tried the test page and it has printed out fine, but are still having issues you could be dealing with a connection issue. Printers can be connected locally or through a network. Local printers are typically connected by a USB while printers use a parallel cable. If you are using a USB, ensure that the USB cable is connected to both the printer and the computer. Try changing the USB cable if you have another one handy, or use a different USB port if available. If the connection is still not working, then the USB or printer drive could possibly be corrupted. A corrupted USB is a software issue.

Parallel cables are hardly used anymore, but if you are using one then ensure that the cables are connected firmly to both the printer and computer. Unlike USB, the parallel cable either works or does not work.

Troubleshooting printers that are part of a network are more difficult. If you do not have experience with printers or computers, it is advisable to contact a specialist to assist you. If multiple computers / printers are affected, make sure that the connection is properly established. The issues could stem from the router / switch, the wrong IP address, or a misconfiguration. For one of these issues, contact your local IT specialist.

If only one computer is giving you a problem, it is possible that the printer is misconfigured with the computer. You can try to reconfigure it, but if that does not work then the issue may be more complex. Again, an IT specialist would be able to help you!

Software problems may be the most difficult of problems to solve. If you want to try to fix the problem before asking for help the first thing you will want to make sure of is that the drivers installed are correct. If the drivers are installed properly, you can try to uninstall the printer, disconnect it, and then reinstall it. If you are still having problems, contact an IT support specialist for more in-depth instruction.

If you find that you are having issues with your printer and none of the solutions mentioned above are applicable to your problem, check the basics. Ensure that the printer has power, it is connected and turned on. Double check that there is the paper in the paper tray and it is put in properly. Sometimes you can fiddle with the paper, take it out and put it back in, to solve the problem. If you are lucky the problem will be easily fixed just by checking the basics!

Sometimes printers will give an error and there is no explanation for what it means. Most printers have a “Doctor” which is a program that you can run which will check for problems and diagnose them. For example, HP has a program called the Print and Scan Doctor which can be used on any computer that used Windows. Unfortunately, for Mac OS X the program doesn’t work.

Depending on what type of printer you have, you might come across a 50.4 Error. Laser printers have a part called the fuser which is what fuses the toner to the paper. Just like the drum unit and the toner cartridge, the fuser will eventually need to be replaced during the life of the printer. According to HP, a fuser lasts about 100,000 so unless you are printing a lot, you won’t need to replace the fuser too often. Keep in mind that the fuser can wear out faster if there are a lot of problems with the printer including paper jams. The quality of the fuser is also important for longevity.

If only half the page is printing out, many things could be wrong. Unplug the printer, turn off the computer and restart both devices. Once everything is back up and running again, run a self-test page. If the self-test page doesn’t print normally, there may be additional error lights on the printer. You can search the web for what the lights mean and go from there. The problem could be concerning the printer or the toner or drum unit. The error message should explain what the problem is, but if it doesn’t you can always search for the error message online to get an in-depth explanation.

If printing photos are one of the main reasons you use a printer, then nothing is worse than blurry or pixelated images. Printing out photos can be tricky, though, because how they appear on the screen is not how they are going to look once you print them out. This occurs because of resolution. The resolution of a printed photo is a lot higher than the resolution of a computer screen. It is important to note that photos that are already blurry or don’t have the correct resolution, will not print out nicely. While it is important to make sure you have a printer that is capable of printing quality photos, if the photos are already blurry there is no way to fix that from the printer.

These signs might mean that the printhead is clogged. If you haven’t used your printer in some time, this can occur and it is important to clean the printhead by running the printer’s utility program. If you are having a hard time finding the program, you can try to access it from the printer device on your computer. Run it a few times and then print out a test sheet to see if the spots have disappeared.

Puddling is a problem in which ink will create a puddle on the paper because the paper can’t absorb the ink properly. This can be easily fixed by using paper designed for the printer. If you are using glossy paper and the printer isn’t built for that type of printing than puddles will occur and there isn’t any other way to get rid of them. If the problem isn’t the paper, then it is problem the printer’s paper settings. Make sure to choose the type of paper from the list and then continue printing.

Most printer technology includes a printer utility tool that allows users to troubleshoot various issues. One of those issues would be jagged vertical lines. Unfortunately, over time the printer head becomes out of alignment. This is going to happen in almost all printers at some point in their lifetime and they will need to be realigned. The printer utility should include an option for correcting this.

If color is missing from a printout, there may be several different reasons. First, make sure the cartridge doesn’t need to be replaced. If the cartridges are full, then it could be a clogged nozzle. Another reason could be the ink has dried up due to inactivity. Inks dry quickly, quicker than toner powders in LED or Laser printers, therefore it might be time to change the ink out.

Banding is a term used to describe a heavy band of ink that forms on paper that are uncoated or art paper when printing at a high resolution. The printers will try to use more ink to adjust for the higher resolution. If banding occurs, it is probably because the printer can’t print at that resolution. Select a lower print quality setting and the banding should subside.

If you have a color printer, you may have the option of turning off the color when printing black and white documents. It might be surprising to learn that doing turning off the color can actually produce poor prints, even for black and white images. The reason is because using all the colors give the documents smoother gradations and richer tone in comparison to simply using black ink. Another issue could be the ink or toner itself. If a color is leaking then it will appear on the printed page. You will have to remove the leaking ink, clean the printer, and replace it with a new one.

If you print out something and it looks similar to the photo shown here, it is normally a sign of stray ink accumulating on the rollers. It may be necessary to clean the printer. Whenever replacing a toner cartridge or drum unit, it is important to be careful not to touch the roller or the toner as it can mess up prints.

A buildup of dust can be a hassle to avoid, but it is important in order to avoid potential problems. Taking care of the equipment and workspace is one way to ensure problems don’t occur. Wipe surfaces down with a lint-free cloth. If the paper feed is not enclosed, brush away the dust made for computer surfaces. Some papers, such as art quality papers, attract more dust than normal paper so it is especially important to clean prior to use with this type of paper.

Printing is performed by the equipment’s graphic processing function. There are many reasons this could be happening. Prior to printing, make sure you have viewed the print preview and if the preview is off, then something with the layout needs to be fixed. Enlargement or reduction of the printed image will be different than what is displayed on the monitor

Images will be cut off if the paper size that is used is not the same as the paper size that is selected in the print settings. Make sure the correct paper is being used. Also, use print preview to see whether the image is being cut off. The image itself may need to be resized in order to fit the page.

In some settings, printers can be connected to more than one computer. This makes for an efficient office setting. However, if the print instruction from one computer was issued, but the printer did not print then there may be a problem with the user authentication. If you are the primary administrator, then it can easily be fixed by authorizing the printer. Otherwise, you will need to contact the administrator to have access.

When printing it is possible that the text or image can be cut off. This occurs when fonts are being mapped incorrectly, or for a different printer that has different metrics. This issue can be resolved by changing the style of the font. In Microsoft Excel or Word, users can select “Normal Style” or a Truefont type. Ensure that either one of those options is selected. Users can find the correct tab under “Format” and “Style.” Picking the appropriate size font may be slightly different with different versions of Microsoft Office.

Missing characters is similar to text truncating. The issue is not with the printer itself, but with the format of the file being printed. When printing with a Truetype font, the fonts can be selected to print as graphics. This setting will fix the issue of missing characters. First, ensure that the font style is either Normal or Truefont type. No matter which version of Microsoft Office that you have you can go to the Setup for the printer and select the options button. Select Print font as graphics and then click ok. The missing character should now print without a problem.

Multifunction printers are able to scan and send faxes. When sending a fax, a message will pop u saying “Awaiting redial.” If a fax doesn’t go through, the machine will redial in 5-minute intervals and then print out a busy or no response report. Users should ensure the following:

Ensure that the telephone line is correctly connected to the printer where it says “Line.” Disconnect and then reconnect to make sure the connection is secured.

On the LCD display of the printer, a message will pop up that reads “Cannot Detect.” This error message will occur after installing a new ink if it was installed too quickly, if it was broken, or if the printer simply needs to be reset. Take out the ink cartridge and replace it into the printer, ensuring that it is in the correct position. For color printers, the color inks need to be placed in the correct positions for the printer to operate. If the error message is still showing, the printer can be reset. Each printer model will have slightly different reset procedures, so it is important to look for the correct reset instructions for the model that you have.

If the LCD display on the machine shows a message that says “Standing by ON/OFF to resume” the machine is going into Save mode. In Save or Off mode, the display will turn black and shut off. Turn the machine on again by pressing the On button or the Power save key. The purpose of Save mode is to preserve the life of the machine if it is not in use every day. During off mode, the printer can still clean the printhead and any connected telephone lines will still be active.

Print Unable 46 is an error message that will occur if the ink absorbers are almost full. When the printhead is cleaned, the ink absorbers hold the ink that is clean from them. Typically, the ink absorbers should last for the life of the machine. If this message appears, it is possible that it is not correct. By updating the machine’s firmware the message should go away.

A multifunctional printer can have problems with communicating between different devices or phone lines. When sending or receiving a fax there could be an interference with the phone line. In this case, try resending the fax. If the message persists, the problem may be because of an incorrect setup of the printer or the phone line. Disconnect the other lines to try to identify what is causing the problem. Ensure that the machine is connected accurately and reconnect the different lines individually.

If the documents being printed are being sent to fax instead of printing, the problem can be easily resolved. The printer setting needs to be changed. Right click on the printer icon in the control panel menu. Click to make it the default device.

The LCD display screen on the printer will show an error message that says “Media full” when a memory card is used that is full. Printers can only save a certain amount of files, therefore if the memory card contains too many it will be able to work with the printer. Try deleting any unnecessary files to free up space on the memory card.

The printer will display messages when it is unable to follow through on a command, whether that is to clean, print, init, or scan. To resolve these issues first, clean the encoder strip. Dirt or foreign particles on the strip is a common cause for many issues. It is important to look up specific directions since each printer model will be slightly different. To clean the strip use a lint-free cloth such as a dry monitor cloth or a T-shirt. It is important to NOT use any paper products. The encoder strip is a clear plastic strip that is located in front of a white band. There will usually be a warning to not touch this strip. That is because it shouldn’t be touched with hands since the oils can damage it.

Sometimes when you go to hit print and the printer begins to warm up, you might hear a disturbing clicking sound. In some cases, the click will begin when you hit print, but then stop and continue printing. In other cases, the clicking will continue and you might not be able to print at all. There are a few possible reasons for the noise. First, if you just replaced your drum unit it is possible that the unit is defective. If the problem persists, the drum unit will need to be replaced for one that works. In other cases, there could be something that is out of alignment of calibration. There is a slider on the drum unit that might be out of alignment. Try sliding it back and forth and make sure it is in the proper position before reinserting it back into the printer. Another possible solution is to check for any obstructions, such as paper. Make sure nothing is blocking the drum unit before trying to print again.

With an HP LaserJet printer, this error might occur when the memory or file system failures will not allow a mopy job to occur. The term mopy may seem like a typo at first, but it is a term for multiple original copies, multiple original prints, or multiple original outputs. A mopy enabled printer produces “mopies” while a photocopier produces copies. A computer user will select an option to print a certain amount of copies of a document via an application or the printer driver interface. When a mopy job error appears, only one copy will be a printer. To resolve this issue, reset the RAM DIMMS and/or the EIO hard disk. Additional memory may need to be installed.

A cleaning page is a process that helps clean the inside of the printer. The process is usually the best when using a sheet of transparency or copier grade paper (18 to 24 lb) with a smooth surface. The printer should be idle and the ready light should be on before processing a cleaning page. The wait time for the cleaning page to process may vary. It can take anywhere from 2 minutes to 5 minutes to be completed.

If the printer produces a page of gray text instead of black it may be because of the print density setting or the photoreceptor. Many laser printers have a print density control that allows users to manipulate the tones of the printed ink. Increase the print density for a deeper and blacker hue. The photoreceptor may also be the culprit of the problem. Over time, the photoreceptor will wear out, hold less of a charge, and ultimately transfer less toner from the developer to the page. This means that the print will look gray. Increasing the print density setting will most likely solve the problem, but eventually, it will need to be replaced. On the other hand, if the print density is too high then a gray background will be produced from an excess of toner. Try adjusting the print density slowly to find the best setting.

If the printed page has spots on it which are spaced at large intervals there is a possibility of a hole, scratch, dent or other flaws on the surface of the photoreceptor. If this piece of the printer can be removed, do so and examine it to determine if there is a flaw. If one is found, then this unit will need to be replaced entirely. If the photoreceptor can’t be removed then it will be necessary to call a service technician to inspect the machine.

The way spots appear on a printed page is important in determining how they are being made and finding a possible solution. Spots that happen at close intervals may be caused by a deposit of toner that is on the fuser. Turn the printer off for at least 15 minutes to allow the fuser to cool off.  The fuser is extremely hot so be caution and ensure that it has cooled properly. Examine the fuser cleaning pad for deposits of toner and replace the cleaning pad if necessary. Unfortunately, the fuser typically can’t be examined by itself and if the problem continues a

If you tried to print out an image, but it was split over two pages it is probably because of a lack of memory to process the page. More memory is required by the printer to print more complex pages and large graphics. Add additional memory if the problem continues to occur. If the printer does not need additional memory, then print a status sheet. A status sheet will show you how much memory is installed and if there are any memory errors. The issue could also be a formatting issue. Make sure that the document is formatted to fit one page. Before printing, check the print preview button to see if the image takes up one or two pages.

The split text is another error similar to split graphics. There may be a setup error in the software application that sends the text. Make sure that the program setup is set to the correct page length, margins, and font size. The split text is hardly caused by the printer itself, therefore look to the computer and the programs that you are printing from for a setup error.

On many multifunction printers, duplex printing is an option. This type of printing allows users to print on both sides of the paper. There are many common errors that can occur with double sided printing. One of the most famous problems is that the pages print upside down and on the backside of the paper. The solution is to select the landscape or portrait produces vertical flipping option. This should change the print job to be the correct orientation. Another annoying problem is that the pages have to be put in order after they have printed. There should be an option for print pages in reverse in the Advanced settings box. Only select this if the pages must be put in order once the printing is complete.

No matter what problem you might be dealing with, we at the Ink Toner Store strive to give you not only the best quality products but also the best service. This overview guide is here to assist you, but if you need further help please don’t hesitate to call our customer service line at 888-720-7888, our representatives are here to help you in any way possible!

The LCD screen is vital for operating the printer. Should you encounter any kind of trouble, such as a dead screen, corrupted text, or other issues, please refer to the guide below.

First of all, unscrew the LCD screen from the printer frame, remove both M3x10 screw holding it the LCD board in the plastic casing, and remove it from the casing. See if the problem still appears when the LCD is not pressed by the casing.

Firmware updates are necessary to keep your printer up to date. However, the installation of incorrect firmware can lead to letter corruption on the LCD screen. There"s an easy fix, though:

There is a small chance the printer"s LCD screen can glitch out by electrostatic discharge when inserting the SD card. Try to turn the printer off and on again.

This problem usually appears only on user-assembled printers. If your printer"s LCD screen remains blank or displays corrupted symbols after you turn on the printer, there is a chance it is caused by incorrect wiring. Follow these steps to fix the issue.

Double-check that all cables are properly seated and they are not visibly damaged. Depending on the model of your printer, please refer to the following guides for information on how to make sure the cables are properly connected: Einsy RAMBo electronics wiring (MK3/MK3S/MK3S+) and Mini RAMBo electronics wiring (MK2S, MK2.5, MK2.5S).

If you suspect that the LCD ribbon cables connectors are not firmly seated in the slots, disconnect the LCD ribbon cables and check the slots for any bent pins. If there are bent pins, you can use tweezers to fix them. However, be very careful not to break the pin(s) completely.

If none of the above resolved the problem, turn the printer off again and try to unplug both of the cables, lay them down on a flat surface and gently stretch them. Then plug them back in and turn on the printer.

I’ve recently acquired a few printers for salvaging the stepper motors out of them. In taking one apart (specifically a Brother MFC-5860CN), I found that the LCD had a 6 pin ribbon cable connected to it. I figured it wouldn’t be too hard to figure out the communication protocol and talk to it so I gave it a shot. Well it wasn’t too hard, but it did take some time and effort.

In case you can’t read upside down and backwards, it says “Please Wait”. I needed to figure out how it was sending those words over the 6 wires that the LCD was connected with. So then I connected my logic analyzer to my computer and started capturing data. The logic analyzer only captures logic for a short window of time, and the message seen above only appears on the screen for about 2 seconds so I had to be quick and precise. I would plug the printer in, then wait a second or so, and then hit capture on the logic analyzer software. This was not easy. After struggling for about an hour I finally got something that looked like the data I was looking for, but I wasn’t sure.

Another quick Google search of “spi tutorial” lead me to a couple of tutorials (first one, second one). Turns out that mysterious line that would go logic low when data was sent was the slave select line. Plugging what I learned into the logic analyzer software and tweaking the settings a bit led me to a really geeky point in my life. I saw the following on the screen and was more excited than I’d like to admit:

“Please Wait” it said. I had learned the language of the LCD. It was using SPI! Now it was time to rig up my arduino to talk to the LCD. So then I did this:

Don’t worry, this isn’t the same connector from before that I soldered wires to for use with the logic analyzer (you were worried weren’t you). Luckily I had a similar Brother printer that used the same LCD and connector. I desoldered the connector from that printer very carefully since it’s mostly made of plastic and plastic tends to melt when you poke it with a soldering iron. Then I soldered on some wires and plugged it in to a breadboard with a 16MHz/5v Arduino pro mini on it. And then, I wrote some code using the SPI library to recreate what I was seeing on the logic lines. And then, I wired everything up and uploaded the code… And then it didn’t work.

My best guess was that, even though I was dividing the clock frequency by 128, 125kHz (16MHz / 128) was just too fast for the little LCD. hrm. Measuring the wavelength of the clock signal in the logic analyzer software showed me that the printer was sending data at 33kHz-ish. I had a 4.096MHz crystal lying around which, with the same setup, would get me to 32kHz. Close enough. I busted out my DIP Atmega328P, wired it up with the crystal, wired it to my Pocket Programmer, plugged it in, tried to program it, remembered that for some reason the pocket programmer only works with the old version of the arduino software, opened arduino version 22, sucessfully programmed the Atmega, and… no luck. Now I was really confused.

My best guess now was that I missed something when looking at the logic. Maybe there was something required at start up for the LCD to work. But I wasn’t about to try and get the timing perfect by plugging in the printer manually and manually clicking capture. That was ridiculous last time, and it took way too long to find the window of logic where the communication was happening. If I tried that method again, frustration and anger would happen, and something might be destroyed. I previously had an idea that I could use my controllable power outlet and some Java code to automate the process of plugging the printer in and pressing the capture button on the logic analyzer software.

I figured I could use some keyboard simulation to press the enter key with focus on the capture button, and that didn’t turn out to be very hard at all. I found that Java’s Robot class made it really easy to simulate the enter key being pressed. Now I needed to figure out how to connect to a device on a COM port, and read from it. This device would be an arduino connected to my controllable power outlet. However, doing this in Java turned out to be not so easy. In fact, apparently this is no longer supported in Java. That sucks. Now what to do.

I combined some proof of concept python scripts and created a script that would allow you to specify waiting times (in milliseconds) for the turning on of the power outlet and the pressing of the enter button. By changing these times (mostly just the power outlet time) I was able to capture data from right after the printer was turned on. There ended up being nothing really useful there, however I kept playing and found a set of wait times that would capture the beginning of the data transmission (which I had seen before when I found it manually). Looking more closely at this logic, I found a sequence of numbers (13, 72 ,9) being sent before each transmission. When I uploaded the program with this sequence of numbers at the beginning of the transmission and did some rewiring it said “Hi”.

I had done it! I successfully reverse engineered the LCD. I turned it on and off a couple of times, dragged my wife over to show her my accomplishment, and then realized that there was something wrong. Occasionally when I turned it on, the letters would smear down so that there were ugly lines showing on the screen instead of the text that was supposed to be showing. It was great that I had figured out how to make something show on the screen, but I wasn’t finished. This project was not complete (are you tired of reading yet?).

My first guess this time was that there was noise in the lines and I needed some filtering caps. After looking at the PCB from the printer, I found that there were some capacitors on there that I had missed when recreating the circuit. So then, I measured the values with a multimeter and found some lying around that had the same value. But inserting these capacitors into my circuit did not fix the problem.

In my original measurements to figure out the ground and power lines of the LCD, I had found that there were 2 lines that read as 5v which were pin 1 and pin 3. I had previously noticed that with only pin 1 connected to 5v the LCD would not work at all, so I had connected pins 1 and 3 together so that they were both at 5v. This was my current setup. I tried the only other option of connecting only pin 3 to 5v, and voila!, the LCD was turning on and printing the text (now “Hello World?”) every time. However, the screen was much more dim than it was when it had occasionally worked with the previous setup.

I was starting to get the idea that pin 1 was the contrast pin, and, after testing my theory by plugging pin 1 into my 5v line on my breadboard after the text was already showing, I found that to the best of my knowledge that pin 1 was indeed a contrast pin. So now my idea was that I needed to pull pin 1 high after the text was already being displayed. I wired pin 1 to pin 12 on my ATMega chip (arduino pin 6) and rewrote my program to turn on pin 6 after the text was being displayed. At this point I’m feeling like I should be really close to just stomping on the whole thing if it doesn’t work. It didn’t work (however it was surprisingly not that frustrating).

I had one last idea to try before I was ready to quit and write this project off as beyond my current knowledge. There were periods of hundreds of milliseconds that I had not seen in the logic. It was time to stop taking shortcuts and just figure the whole thing out, so I, once again, got out my controllable power outlet setup, and started precisely writing down everything that I saw in the logic. What I found (from my notes):

UPDATE: Here’s a pinout to for the ribbon connector. Also I’ve added my arduino library and demo code to Github. For immediate use, you can download the BroLCD library and demo code as a zip file here.

If you"re using the Sign In App free trial you might not have a compatible Brother label printer, don"t worry you can make use of all of the other features included in the free trial. You can check the list below to see which badge printers are compatible with Sign In App.

Tap Add a Bluetooth printer to see a list of the available Bluetooth printers. Select Add a network printer to see the availble network printers, you can also enter your IP address manually from here.

While it churns out 110 address-sized labels per minute like the comparable QL810W Wireless Printer (UBRO4), this wireless label printer features an LCD display that makes connecting to WiFi a breeze. As a stand-alone unit, it requires no computer or configuration software.

This wireless label printer requires drop-in label rolls; print names on white labels, or for last minute attendees, prints on clear labels for affixing to logo-only Event Badges. Free Apple and Android app included is ideal for iPhone, iPad and Android devices. Also connects via Bluetooth and Ethernet.

Returnable within 15 days: All technology products including, without limitation: printers, scanners, wireless technology, and accessories. These products cannot be returned if they have been used or are not in the original packaging. A restocking fee will apply to all technology products that have not been used but have opened boxes: 15% of the current retail price.  View ourReturn Policyfor more details.

This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.