3.5 tft lcd shield arduino mega manufacturer

This TFT 3.5 Inch LCD display support 480x320 pixel resolutions. The display uses the ILI9481 graphics controller. The module includes the 5V-3.3V power conversion circuit and no additional level conversion circuitry is required. This Module can be inserted directly into the Arduino Mega2560 Board.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (3.5" diagonal) bright (6 white-LED backlight) and colorful (18-bit 262,000 different shades)! 320x480 pixels with individual pixel control. As a bonus, this display has a optional resistive touch panel with controller XPT2046 attached by default and a optional capacitive touch panel with controller FT6236 attached by default, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover.

The pin32 (SDO) of 3.5 display module is also used by touch panel or SD card SPI interface, so we must cut off this pin to avoid conflict with the touch panel or SD card.

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you"ll have it running in under 10 minutes! Works best with any classic Arduino (Due/Mega 2560).

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. You can connect more sensors, buttons and LEDs.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!" - we"ve written a full open source graphics library at the bottom of this page that can draw pixels, lines, rectangles, circles and text. We also have a touch screen library that detects x,y and z (pressure) and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

If you"ve had a lot of Arduino DUEs go through your hands (or if you are just unlucky), chances are you’ve come across at least one that does not start-up properly.The symptom is simple: you power up the Arduino but it doesn’t appear to “boot”. Your code simply doesn"t start running.You might have noticed that resetting the board (by pressing the reset button) causes the board to start-up normally.The fix is simple,here is the solution.

The 3.5inch TFT LCD Module is based on ILI9481 LCD driver that includes Micro SD slot. This module gives nice picture quality and works well with Arduino Uno and Arduino Mega controllers. This kind of module is not a touch screen display. No...

As it stands I am not able to use the LCD screen. When I run the program graphictest_kbv I get an "image" but it is full static (like an old VCR player)

This 3.5 inch TFT LCD Display is the larger version of the 2.4″ display designed specifically for Arduino Mega. This Arduino shield contains a 16 bit color TFT screen with a large 3.5″ display and is designed to fit directly into the standard headers of an Arduino Mega requiring no additional interface hardware. It support a relatively high resolution of 480 x 320 pixels.

This TFT LCD Screen Module , not just a LCD break but include the Touch , SD card and Flash design. So it"s a powerful extension module for your project.

Kuongshun Electronic, one of the international well-known manufacturers and suppliers of 3.5 inch tft touch screen module for mega 2560 r3 which is situated in China, now has quality products for sale. We are equipped with a group of professional and experienced workers, as well as advanced equipment. You can rest assured to buy discount and low price 3.5 inch tft touch screen module for mega 2560 r3 made in China from us and check the pricelist with us.

Now, I have bought 3.5" TFT LCD display for my Arduino Mega 2560 R3 to try whether I could run the screen or not, and it is not working now! I am so depressed and angry for these two"s misbehaviors. I have already checked website and a lot of Arduino IDE code examples and libraries such as UTFT.h, UTouch.h, UTFT_MEGA, UTFT_CTE, TFTLCD. I tried these and I can not run my 3.5" screen. Where am I faulty? There is something below the screen shield: www.mcufriend.com and 3.5" TFTLCD for Arduino 2560. Are there any basic code or have anyone tried to run Mcufriend"s displays correctly?