lcd panel ips vs tn made in china

When it comes todisplay technologies such asprojectorsand panels, factors such as resolution and refresh rate are often discussed. But the underlying technology is equally, if not more, important. There are tons of different types of screens, from OLED and LED to TN, VA, and IPS. Learn about the various monitor and television types, from operation to pros and cons!

1)Film layer that polarizes light entering2)glass substrate that dictates the dark shapes when the LCD screen is on3)Liquid crystal layer4)glass substrate that lines up with the horizontal filter5)Horizontal film filter letting light through or blocking it6)Reflective surface transmitting an image to the viewer

The most common form of monitor or TV on the market is LCD or Liquid Crystal Display. As the name suggests, LCDs use liquid crystals that alter the light to generate a specific colour. So some form of backlighting is necessary. Often, it’s LED lighting. But there are multiple forms of backlighting.

LCDs have utilized CCFLs or cold cathode fluorescent lamps. An LCD panel lit with CCFL backlighting benefits from extremely uniform illumination for a pretty even level of brightness across the entire screen. However, this comes at the expense of picture quality. Unlike an LED TV, cold cathode fluorescent lamp LCD monitors lack dimming capabilities. Since the brightness level is even throughout the entire array, a darker portion of scenes might look overly lit or washed out. While that might not be as obvious in a room filled with ambient light, under ideal movie-watching conditions, or in a dark room, it’s noticeable. LED TVs have mostly replaced CCFL.

An LCD panel is transmissive rather than emissive. Composition depends on the specific form of LCD being used, but generally, pixels are made up of subpixel layers that comprise the RGB (red-green-blue) colour spectrum and control the light that passes through. A backlight is needed, and it’s usually LED for modern monitors.

While many newer TVs and monitors are marketed as LED TVs, it’s sort of the same as an LCD TV. Whereas LCD refers to a display type, LED points to the backlighting in liquid crystal display instead. As such, LED TV is a subset of LCD. Rather than CCFLs, LEDs are light-emitting diodes or semiconductor light sources which generate light when a current passes through.

LED TVs boast several different benefits. Physically, LED television tends to be slimmer than CCFL-based LCD panels, and viewing angles are generally better than on non-LED LCD monitors. So if you’re at an angle, the picture remains relatively clear nonetheless. LEDs are also extremely long-lasting as well as more energy-efficient. As such, you can expect a lengthy lifespan and low power draw. Chances are you’ll upgrade to a new telly, or an internal part will go out far before any LEDs cease functioning.

Further segmenting LED TVs down, you’ll find TN panels. A TN display or Twisted Nematic display offers a low-cost solution with low response time and low input lag. TN monitors sport high refresh rates, so 100Hz, 144Hz, or higher. Thus, many monitors marketed toward gamers feature TN technology. Unfortunately, while an affordable, fast panel may sound ideal, TN panels suffer from inferior colour reproduction and horrible viewing angles. A TN panel works so that liquid crystal molecules point at the viewer, and light polarizers are oriented at 90-degree angles.

Like TN, IPS or In-plane Switching displays are a subset of LED panels. IPS monitors tend to boast accurate colour reproduction and great viewing angles. Price is higher than on TN monitors, but in-plane switching TVs generally feature a better picture when compared with twisted nematic sets. Latency and response time can be higher on IPS monitors meaning not all are ideal for gaming.

An IPS display aligns liquid crystals in parallel for lush colours. Polarizing filters have transmission axes aligned in the same direction. Because the electrode alignment differs from TN panels, black levels, viewing angles, and colour accuracy is much better. TN liquid crystals are perpendicular.

A VA or vertical alignment monitor features excellent contrast ratios, colour reproduction, and viewing angles. It’s a type of LED monitor with crystals perpendicular to the polarizers at right angles like TN monitors. Pricing varies, but response time isn’t as high as a TN monitor.

A quantum dot LED TV or QLED is yet another form of LED television. But it’s drastically different from other LED variants. Whereas most LED panels use a white backlight, quantum dot televisions opt for blue lights. In front of these blue LEDs sits a thin layer of quantum dots. These quantum dots in a screen glow at specific wavelengths of colour, either red, green, or blue, therefore comprising the entire RGB (red-green-blue) colour spectrum required to create a colour TV image.

QLED TV sets are thus able to achieve many more local dimming zones than other LED TVs. As opposed to uniform backlighting, local dimming zones can vary backlighting into zones for adjustable lighting to show accurate light and dark scenes. Quantum Dot displays maintain an excellent, bright image with precise colour reproduction.

An OLED or organic light-emitting diode display isn’t another variation of LED. OLEDs use negatively and positively charged ions for illuminating individual pixels. By contrast, LCD/LED TVs use a backlight that can make an unwanted glow. In OLED display, there are several layers, including a substrate, anode, hole injection layer, hole transport layer, an emissive layer, blocking layer, electron transport layer, and cathode. The emissive layer comprised of an electroluminescent layer of film is nestled between an electron-injecting cathode and an electron removal layer, the anode. OLEDs benefit from darker blacks and eschew any unwanted screen glow. Because OLED panels are made up of millions of individual subpixels, the pixels themselves emit light, and it’s, therefore, an emissive display as opposed to a transmissive technology like LCD/LED panels where a backlight is required behind the pixels themselves.

Image quality is top-notch. OLED TVs feature superb local dimming capabilities. The contrast ratio is unrivalled, even by the best of QLEDs, since pixels not used may be turned off. There’s no light bleed, black levels are incredible, excellent screen uniformity, and viewing angles don’t degrade the picture. Unfortunately, this comes at a cost. OLEDs are pricey, and the image isn’t as bright overall when compared to LED panels. For viewing in a darkened room, that’s fine, but ambient lighting isn’t ideal for OLED use.

As you can see, there are tons of different types of displays, each with their advantages and disadvantages. Although many monitors and TVs are referred to by different names like LED, IPS, VA, TN, or QLED, many are variations of LCD panels. However, specific technology such as the colour of backlighting and alignment of pixels dictates the picture quality. OLED is an entirely different form of display that’s not LED. Now that you understand the various types of monitors and televisions on the market, you can select the best TV to fit your needs!

Everyday, we look at LCD display, TV, cell phone, monitor. It becomes a necessity in modern society. LCD panel is the most important part of an LCD display. It determines LCD screen"s performance, e.g. brightness, contrast, color and viewing angle. Therefore, picking the right type of LCD panel is critical to your application.

These names reflect the alignment of crystal molecules inside the LCD, and how they change when they are charged electrically. All liquid crystal displays change the alignment of liquid crystal molecules to work, but the manner in which they do so can drastically affect the image quality and response time. Each panel type has its advantages and disadvantages. The easiest way to choose between them is to decide which attributes are most important to your project. It mainly depends on what you use your LCD display for, and your budget.

TN is the most mature technology in LCD panel manufacturing. When there is no voltage difference between the two transparent electrodes, liquid crystal molecules are twisted 90 degrees, in combination of upper and bottom polarizers, allows light to pass through LCD. As voltage applied, crystal molecules are untwisted and aligned to the same direction, blocking light.

In IPS panel, crystal molecules are parallel to the glass substrates at initial stage, LCD is off. When the in-plane electrodes is charged, crystal molecules are rotated, modifying light"s direction. Which lights up the LCD display.

As its name suggests, VA panel"s liquid crystals are aligned vertically without charged. When a voltage is applied, the molecules tilt and modifying light direction.

So in summary, TN panels twist, IPS panels use a parallel alignment and rotate, while VA panels use a perpendicular alignment and tilt. These difference create LCD display with distinctive performance.

IPS LCD is the clear winner in this aspect. It has 178/178 viewing angle ratings. Which means you can look at IPS LCD display from any angle without the image shifting in color and contrast. VA LCD has pretty wide viewing angle, too. But it has contrast shifts at off-center angles. As for TN LCD, viewing angle is its weakest point.

Most TN LCDs have 6-bits colors. Manufacturers use frame rate control (FRC) to enhance its color performance. For IPS and VA panels, you can still find 6-bits entry level LCD. But most of them are 8-bits. And IPS technology can provide natively 10-bits colors.

Color gamut is another part that VA and IPS panels shine at. The best TN LCD can reach sRGB gamut. VA panels typically start with full sRGB coverage, and get to around 90% DCI-P3 coverage. With IPS LCD panel, you could find the best ones full DCI-P3 and Adobe RGB coverage. That is why you see most professional grade LCD displays use IPS panel.

There is no inherent differences among the three panel technologies, because LCD backlight is the main factor here. However, there is a big gap in terms of contrast ratio. TN LCD panel tends to have the lowest value among the three. IPS LCD screen sits in the middle can reach 1500:1. For VA panel, the best one can exceed 4500:1 easily. VA LCD display provides far darker screen than TN & IPS. That is why they are used in vehicle dashboard.

TN panel does have an advantage when it comes to refresh rate. The panel offers the best refresh rate and response time. This is the reason why most gaming LCD monitors are made of TN panel.

TN LCD provides the best refresh rate and economic solution. If your application requires wide viewing angles and good color presentation, VA panel is probably the choice. While IPS has the best overall visual performance, in general it is more expensive than the other two.

TN stands for twisted nematic. This is a type of LED (a form of LCD) panel display technology. TN panels are characterized as being the fastest and cheapest among the other main types of display panels, VA (vertical alignment)and IPS (in-plane switching). As such, they work great for gaming monitors and gaming laptops. However, TN panels also offer the worst viewing angles and color when compared to VA and IPS panels.

PerformanceFastest: low response times, highest refresh rates, minimal motion blur; Low input lagLongest response times typically; Higher refresh rates possibleSlower response times than TN, faster response times than VA; Gaming-quality refresh rates are rare

DisplayWorst viewing angles;Worst colorViewing angles typically better than TN, worse than IPS; Good color; Best contrast;Best image depthBest viewing angles; Best color

You may be surprised to know that not all LCD panels are created equal. That’s because there’s more than one type of LCD screen. While their differences are subtle, the type of panel technology significantly impacts its image quality and display performance.

In this post, we’ll compare the three types of LCD panel technologies – IPS vs. TN vs. VA – and the pros and cons of each. Knowing the differences is critical to help you find the best type that fits your needs.

The main difference between them is how they arrange and move the liquid crystal display (LCD) molecules in their panels. This, in turn, has a profound effect on image quality, refresh rate, and other performance factors.

A twisted nematic or TN monitor is the oldest and most common type of LCD still used today. It uses a nematic liquid crystal, meaning it has its molecules arranged in parallel, but not on a level plane. These can twist or untwist themselves when a voltage runs through them, hence the name. This twisting effect either allows or blocks light from passing through, turning screen pixels “on” or “off.”

In-panel switching (IPS) panels work similarly to TN monitors, except that the liquid crystal molecules are parallel to the glass panel of the screen. Instead of twisting like in TN monitors, these molecules rotate when a voltage is applied.

Vertical alignment (VA) displays arrange their LCD molecules vertically, perpendicular to the glass panel. When voltage is present, they tilt themselves instead of twisting or rotating.

Being the oldest LCD technology still in use today, TN monitors undoubtedly have their share of benefits, otherwise they wouldn’t have this much longevity! Comparing TN vs. IPS and VA, TN panels are the cheapest and fastest to manufacture. As a result, they are better for the more budget-conscious user. They’re also the most versatile LCD type and have no real-world limits on size, shape, resolution, and refresh rate.

You’ll be hard-pressed to find a TN monitor in a reasonable price range that can display 24-bit (8 bits per channel) color at a wide color gamut, and contrast is limited. The second problem with TN monitors is that because the molecules are not oriented uniformly across the plane, it suffers from a narrow viewing angle. That is, anyone looking at the screen off-axis, such as from a 45-degree angle, will most likely find the image completely un-viewable.

Comparing IPS vs. TN, the former is a drastic improvement over the latter. IPS panels resolve some of the limitations and problems of TN monitors, specifically color accuracy and issues with viewing angles. However, IPS panels suffer from a phenomenon called “IPS glow,” where you can see the display’s backlight clearly if you view it from the side.

Another significant limitation of IPS panels, particularly for gamers, is that they have the lowest refresh rates of any LCD type. And while the color fidelity is fantastic with IPS vs. VA, the latter has superior contrast ratios over the IPS panels.

The biggest strength of VA panels lies in their excellent contrast ratio. Keep in mind that irrespective of the LCD technology used, a backlight is required; this is typically LED. The LCD’s ability to block this light will determine how well it can reproduce blacks, and it’s in this detail where VA excels. That is, blacks are dark and rich in a VA panel vs. IPS. They also lie somewhere in the middle regarding overall image quality, color reproduction, viewing angle, and refresh rate. Overall, VA is a good compromise between TN and IPS.

A drawback of VA vs. IPS and TN is it exhibits an relatively high response time. As such, VA displays are more prone to motion blur and ghosting if you’re viewing fast-moving visuals on a screen, such as when you’re playing a racing game.

It’s worth noting that there is no universal “right” choice for choosing a type of LCD panel. Which one you pick depends on your budget, your intended use, and your expected outcome.

A TN monitor is best if you’re looking for a low-cost, readily available display for tasks that don’t rely on contrast and color accuracy, such as sending emails or typing a document or spreadsheet. They are also the best choice for competitive gamers who want the best refresh rates and response times to give them an edge in online multiplayer games, despite a technically lower image quality.

With their superior color reproduction, IPS panels are best for graphic designers, film editors, photographers, and other visual design professionals. For them, image quality including contrast and color accuracy are more important than refresh rates. IPS panels are also fantastic for casual gamers who want the best visuals and don’t mind the compromise in refresh rate or response time.

Whichever LCD type you choose, make sure you get the right cable, a Premium High Speed HDMI® Cable, or an Ultra High Speed HDMI® Cable to ensure delivery of all the HDMI 2.1 features. Doing this ensures that you’ll get the best experience on your screen.

PC monitors and laptop screens come in all manner of shapes and sizes, but at their heart nearly all have one thing in common: an LCD panel. But not all LCDs are created equal. Some are better for gaming, some offer better contrast and some produce more accurate-looking colours. So, which is the best LCD type for your needs?

We’ll get to how the technology works below, but what you probably want to know off the bat is which technology is right for you. Here we’ll break down the main characteristics of each type: IPS, VA and TN.

Both IPS and VA have two main advantages over TN panels. The first is that they offer much better viewing angles. In other words, you can view both VA and IPS panels from far shallower angles and still be able to see what’s on-screen without much, or any, colour degradation. This is quite a big deal.

VA panels don’t tend to be quite as good as IPS, and as a result there can be a somewhat noticeable variation in brightness when viewed from different angles. ButIPS suffers from what’s known as ‘IPS glow’. This is where the backlight of the LCD shines through when the display is viewed from a certain angle.

Another advantage of IPS and VA panels is that both tend to present better colour reproduction – again, because they simply have a more controlled and precise ability to manage the light that passes through.

As for other differences, IPS tends to have a faster response time than VA since its crystals don’t have to tip over and then twist as they do with VA (see below). You can get fast-refreshing gaming monitors that use VA, but they offer a poor experience due to the slow pixel response time. IPS is slower than TN, but can be fast enough for responsive gaming.

Meanwhile, VA’s last hurrah is contrast. Since its resting state blocks light, its black level is the lowest of all LCDs, yet it can still produce bright colours when needed. A typical IPS or TN panel will have a contrast of 1000:1 or lower. VA panels can double that. This is the reason VA tends to be the best choice for TVs, where a deep black level is important for enjoying movies.

As for TN, it isn’t all bad news – it has a couple of key advantages. The first is that it’s easier to produce so can be used to make cheaper monitors.

If you’re after a monitor that offers great image quality for day-to-day work and image editing, but aren’t particularly bothered about super-competitive gaming, then go for an IPS screen. They deliver the best all-round experience for work and play, and you can still get gaming IPS monitors that refresh at over 100Hz, making them nearly as good as the best TN gaming screens.

However, if gaming is your be-all and end-all then TN is the way to go. Not only are they the most responsive – with the latest displays having refresh rates of 240Hz – but they also tend to be relatively affordable.

That leaves VA, which is the least suited for fast-paced gaming and isn’t as good as IPS for most day-to-day computing such as reading emails, browsing the web and writing documents. However, great contrast levels means it’s the best for watching video and playing some games. So, if you’re looking for a screen to be part of a a multimedia hub then VA might suit your needs.

In the case of LCDs, a grid of pixels made from liquid crystal is sandwiched between two polarising filters and placed in front of a backlight. As light passes through this assembly, it’s either blocked by the second filter or allowed to pass, depending on the orientation of the molecules in the liquid crystal. Vary the voltage and it varies the orientation of the molecules.

This basic principle is what controls the pixels of any LCD panel. Split each pixel into three and add colour filters for red, green and blue and you have yourself a colour LCD screen.

These fundamentals apply to all the different types of LCD available to buy. However, in order to improve certain characteristics of the displays, different types of LCD have been developed that tweak the way in which the liquid crystal, polarising filters and the electrodes are arranged and controlled.

The original and most basic version of a modern LCD is TN, or twisted nematic. This has the polarisers arranged at ninety degrees to one another, so that – normally – no light passes through them. However, the resting state of the crystal has the molecules arranged in a helix, which twists the polarisation of the light as it passes through, in turn allowing it to pass through the second filter.

When a voltage is applied to the liquid crystal the molecules point directly towards the viewer, so no longer twisting the light, resulting in it being blocked by the second polarising filter. TN works well enough, but famously suffers from poor viewing angles (see above), which is why alternative models were developed.

The most famous of these is IPS, or in-plane switching. Here the polarising filters are in the same orientation so that light is blocked when the crystal is in its resting twisted state, rather than allowed to pass through as it would in TN. Then, when activated, the crystals line up in the same direction as the polarising filters and parallel to their surface: for instance, when switched they’re in-plane.

There are several variations on IPS, such as S-IPS and H-IPS, that use slightly different pixel structures and layouts, and have optimisations for faster response times – most displays that are referred to as IPS are in fact S-IPS panels – but the fundamentals are the same.

Samsung has also developed PLS as an alternative to IPS. It’s basically a reworking of the technology that allows Samsung to manufacture the panels without infringing on existing patents.

The other most common variant is Vertical Alignment (VA). Here the crystals are arranged perpendicular to the polarisers, which are again orientated at right-angles as they are with TN. As such, in its resting state a VA panel blocks light as the light isn’t being twisted. When a voltage is applied the crystals tip to a more horizontal position and twist, allowing light to pass through.

When buying a gaming monitor, most consumers are not even aware of the existence of LCD panel technology. LCD display panels have different specs that can have a radical impact on  the user experience. Based on how you plan to use your LCD monitor, you may choose among three main gaming monitor panel types: TN, IPS, and VA.

At first, choosing the right monitor panel may seem tricky. In this article, we will present the pros and cons of each LCD display panel. After finishing reading this post, you will be knowledgeable enough to challenge any sellers and choose the most appropriate gaming monitor for your next playing section.

Let’s begin with the most popular LCD display panel on the market today. TN panels are generally installed in most gaming monitors, especially in those with a high refresh rate.  These kinds of LCD monitors are specially designed for very competitive video games.

One of the advantages of these panels is their relatively lower price compared to their counterparts. Another quality that makes TN panels a top pick is their fast response time. This means that there is a much lower delay between a click of the mouse or a keyboard touch and the command reproduced on the screen. This feature makes the TN panels ideal for those who love action shooters and video games that require very fast reactions. Besides, there are other benefits to having a shorter response time. Overall, there are fewer unpleasant phenomena such as blurring and ghosting. As a result, the final image is much clearer and sharper.

When buying TN panels, you will probably hear the terms ‘black-to-black’ or ‘grey-to-grey’ (GTG). Black-to-black is the standard response time measure. BTB refers to the amount of time it takes a pixel to go from black to white and then back to black. This indicator is considered among the most accurate to evaluate the response time of a device.

Monitors with IPS panels, rely on high colors definition. Looking at this type of LCDs, the quality that stands out the most is the exceptional color accuracy coupled with the wide viewing angles. The wide angularity makes these monitors more suitable for jobs that require a high intensity of colors displayed such as photo and video editing. In gaming, IPS panels are often preferred for RPGs with astonishing visuals.

IPS panels allow you to look at the screen perfectly from any position. These screens do not have the usual problems of changing colors or contrast as with most monitors. Unfortunately, to reach such a high definition of images, the response time must be sacrificed. When compared to TN panels, the response rate is much lower. Technology has undoubtedly updated itself in recent years leading to newest iteration improvements. Besides, most people do not encounter lag problems when playing video games on these screens.

Ultimately, for many casual gamers, image quality is much more important than a couple of milliseconds of delay in the panel’s overall response time. A disadvantage that we have to mention though is the high price. This is one of the critical aspects that turns costumers away from IPS to buying a TN solution.

Finally, there are the VA or Vertical Alignment panels. Much more similar to IPS, there are many types of VA panels, but the ones we will focus on are MVA (Multi-domain Vertical Alignment) panels and AMVA (Advanced MVA) panels.

MVA panels were initially designed to be in the middle between TN and IPS displays, as they offered a better viewing angle than TN screens and a higher contrast ratio and deeper blacks than IPS displays. However, their color accuracy is not as precise as the one of IPS monitors, and they do not have a particularly fast response time.

AMVA panels, on the other hand, focus precisely on a higher color definition. As a matter of fact, they have better color accuracy while preserving ultra-high contrast ratios and deep blacks. Their viewing angle is not as wide as that of IPS panels, and their response time is still a bit slow.

Consequently, monitors with VA panels can be seen as a good compromise among all the market monitors. Their flagship features are the excellent black levels – which is the best in the category of gaming monitors – and their amazing contrast ratio. Moreover, compared to TN panels, they have a better viewing angle and greater color accuracy.

On the downsides, despite apparently trying to correct and eliminate the weaknesses of their competitors, VA solutions do not have a color accuracy comparable to that of IPS panels or a response rate higher than TN screens.

To sum it up, for competitive online gamers, we would suggest TN panels. For non-competitive PC games, VA panels will work much better. If you just want to focus on visuals, IPS displays are a better choice. At Aiwa, we are dedicated to providing the best user experience to our customers.

If you are interested in LCD display panels and screens, you need to go any further. Hopefully, this guide was helpful in sharing more useful information for your next purchase. Come to check our solutions or contact us at any time!

IPS (In-Plane Switching) lcd is still a type of TFT LCD, IPS TFT is also called SFT LCD (supper fine tft ),different to regular tft in TN (Twisted Nematic) mode, theIPS LCD liquid crystal elements inside the tft lcd cell, they are arrayed in plane inside the lcd cell when power off, so the light can not transmit it via theIPS lcdwhen power off, When power on, the liquid crystal elements inside the IPS tft would switch in a small angle, then the light would go through the IPS lcd display, then the display on since light go through the IPS display, the switching angle is related to the input power, the switch angle is related to the input power value of IPS LCD, the more switch angle, the more light would transmit the IPS LCD, we call it negative display mode.

The regular tft lcd, it is a-si TN (Twisted Nematic) tft lcd, its liquid crystal elements are arrayed in vertical type, the light could transmit the regularTFT LCDwhen power off. When power on, the liquid crystal twist in some angle, then it block the light transmit the tft lcd, then make the display elements display on by this way, the liquid crystal twist angle is also related to the input power, the more twist angle, the more light would be blocked by the tft lcd, it is tft lcd working mode.

A TFT lcd display is vivid and colorful than a common monochrome lcd display. TFT refreshes more quickly response than a monochrome LCD display and shows motion more smoothly. TFT displays use more electricity in driving than monochrome LCD screens, so they not only cost more in the first place, but they are also more expensive to drive tft lcd screen.The two most common types of TFT LCDs are IPS and TN displays.

Panel type names are based on the molecule arrangement on a liquid crystal display - LCD monitor - and the changes that occur upon voltage application. LCD monitors - see also LED vs LCD review - adjust the molecule positioning to function, though the way the changes occur immensely impacts your response time and image quality.

While it is the oldest panel technology, a TN panel still has some advantages over the newer VA and IPS panel technologies (see QLED and IPS). For one, they are the cheapest and suitable if you want budget-friendly options . If the extent of color reproduction or better viewing angles is not essential, a TN screen might suit you.

Moreover, TN panels have the least input lag of about one millisecond. A TN computer can operate at fast refresh rates reaching 240 Hz (see 1440p - 240Hz monitors review). For this reason, they are ideal for competitive players seeking gaming monitors (check out the best monitors for Xbox One X and Xbox Series X) that enable them to take advantage of each second. The Benefits of a good monitor for gaming are shown also in our review of monitors for League of Legends.

Nevertheless, TN display technology has notable disadvantages starting with the small viewing angles on the perpendicular axis. The changing of your TN computer"s colors is common when seated at extreme angles.

TN screens also have poor color reproduction. Most TN displays cannot function at 24-bit true color, so they depend on interpolation for accurate shade simulation. This performance can lead to color banding and lower contrast ratios than VA and IPS panel technologies.

TN panels also have a relatively lower color gamut. Only high-end TN monitors display wide color ranges. Many lack a wide-gamut and therefore are unideal for color grading, web design, photo and video editing, or other usages demanding color accuracy.

With their much wider viewing angles compared to TN screens, IPS panels allow you to sit at extreme angles while getting accurate color displays. Those characteristics are also the reason why IPS displays are good for touchscreens in tablets and portable monitors suh as this ZenScreen Touch monitor from Asus or this from Elecrow, an open hardware facilitation company based in China. Unlike a TN screen, you"ll hardly notice a color shift when looking at the screen from an unideal perspective.

IPS panels also have excellent performance in black reproduction, vital in eliminating the washed-out displays typical on TN panels. Regardless, IPS monitors don"t have as high contrast ratios as VA panels.

While TN panels dominate in terms of the refresh rate, IPS panels are now available that support refresh rates even over 240 Hz. For instance, the ASUS TUF VG259QM 24.5-Inch has a 280 Hz refresh rate and features an IPS monitor (see also this 23.8-inch monitor from HP).

TN displays previously had lower lagging than any other panel type, but IPS displays are now at per. LG launched their Nano IPS UltraGear screens boasting of the fastest response times on IPS at one millisecond. Moreover, Samsung"s quantum dot technologies, which will be covered in another post, are more energy-efficient and offer enhanced color accuracy over IPS, as well.

Despite measuring up, you"ll still spend more to get an IPS screen with a one millisecond response time than a similar-rated TN monitor. If you want to benefit from IPS technology at a budget cost, expect an LCD panel at approximately four milliseconds. Dell S2318HN here has gone a step further though, combining IPS and LED - see also "What is OLED?" - technology for some great results.

Another notable demerit dominant in IPS panels is the IPS glow. If this phenomenon occurs, your screen"s backlight shines and blurs your view when sitting at extreme viewing angles. While not the biggest issue, it is something to consider if you like sitting on the side. On the other hand, these types of monitors are thin and lightweight (see "Auzai"s portable monitor", or this Desklab monitor), as well as energy-efficient. Speaking of portability, ASUS mb168b monitor and AOC e1659fwu are also easy to carry and offer good quality at an affordable price.

VA panels form a middle ground between IPS and TN monitors. They have the highest contrast ratios, making them a go-to option for TV manufacturers. While an IPS screen can have 1000:1, comparable VA alternatives may reach up to 3000:1 or 6000:1 contrast ratios.

A VA monitor won"t offer you as good of a performance as an IPS screen in viewing angles (see Lenovo Thinkvision m14). Depending on your sitting arrangement, you may experience some brightness, though not as glaring as the IPS glow.

VA panels feature slower response times than TN and IPS monitors at their best performance. While some VA monitors refresh at up to 240 Hz, they tend to have latency that can cause motion blur and ghosting.

As a result, if you are in a VS vs IPS monitor dilemma, it is wise to refrain from VA displays for competitive gaming, and go for top gamers" choice displays like in these monitors for CS: GO or these monitors for racing games.

Compared to TN panels, VA screens provide better color reproduction, often supporting full sRGB spectrum even on budget options (see the best monitors under $200 review).

Because of their attributes, VA panels are suitable for general use. However, these panels tend to perform lower in most specs apart from the contrast ratio. VA monitors are pretty excellent in single-player action, flight simulations, or casual gaming.

Media professionals prefer IPS panels to VA panels, given their wider color gamut, though professionals like music producers require different features in their monitors.

Again, IPS is the clear winner here. The vertical viewing angles are very similar to the horizontal ones on both IPS and VA panels. Unfortunately, this is one area where TN panels are usually much, much worse. TN monitors degrade rapidly from below, and colors actually inverse - resulting in a negative image that can be distracting. For this reason, if you decide to buy a TN monitor, look for one with an excellent height adjustment, or consider buying a VESA mounting arm, as you should mount TN monitors at eye level. Even when mounted properly, larger TN displays can appear non-uniform at the edges.

There"s usually not much difference between VA and IPS panels in terms of gray uniformity. It"s rare for monitors to have uniformity issues, and even on monitors that perform worse than average, it"s usually not noticeable with regular content. TN monitors tend to perform a bit worse than usual, though, and the top half of the screen is almost always darker than the rest, but that"s an artifact of the bad vertical viewing angles.

Black uniformity tends to vary significantly, even between individual units of the same model, and there"s no single panel type that performs the best. It"s rare for monitors to have good black uniformity, and almost every monitor we"ve tested has some noticeable cloudiness or backlight bleed. IPS and TN panels can look slightly worse due to their low contrast ratios, as the screen can take on more of a bluish tint when displaying dark scenes. Like with contrast, black uniformity issues usually aren"t very noticeable unless you"re looking at dark content and you"re in a dark room. If you only use your monitor in a bright environment, generally speaking, you don"t need to worry about black uniformity.

Historically, TN panels used to have the worst colors, as many of them were cheaper models that only supported 6-bit colors or used techniques like dithering (FRC) to approximate 8-bit colors. Most displays today, including TN models, are at least 8 bit, and many of them are even able to approximate 10-bit colors through dithering. New technologies, like LG"s Nano IPS and Samsung"s Quantum Dot, add an extra layer to the LCD stack and have significantly improved the color gamut of modern IPS and VA displays, leaving TN a bit behind. Between them, NANO IPS is slightly better, as it tends to offer better coverage of the Adobe RGB color space. Although the difference is minor, IPS panels still have a slight edge over VA and TN displays.

Although TN panels have caught up a bit in the SDR color space, they"re far behind when it comes to HDR, so if you"re looking for a good HDR color gamut, avoid TN panels. Between VA and IPS panels, the difference isn"t as significant; however, IPS panels still have a slight edge. The best VA panels top out at around 90% coverage of the DCI P3 color space used by most current HDR content. IPS panels go as high as 98% coverage of DCI P3, rivaling even some of the best TVs on the market. Due to the very high coverage of DCI P3 on both VA and IPS, the difference isn"t that noticeable, though, as most content won"t use the entire color space anyway.

Although not necessarily as noticeable to everyone as the differences in picture quality, there can also be a difference in motion handling between IPS, VA, and TN displays. TN panels historically offered the best gaming performance, as they had the highest refresh rates and extremely fast response times. Manufacturers have found ways to drastically improve the motion handling of VA and IPS panels, though, and the difference isn"t as pronounced.

LCD panel technology has changed drastically over the last few years, and the historical expectations for response time performance don"t necessarily hold anymore. For years, TN monitors had the fastest response times by far, but that"s started to change. New high refresh-rate IPS monitors can be just as fast.

VA panels are a bit of a strange situation. They typically have slightly slower response times overall compared to similar TN or IPS models. It"s especially noticeable in near-black scenes, where they tend to be significantly slower, resulting in dark trails behind fast-moving objects in dark scenes, commonly known as black smear. Some recent VA panels, such as the Samsung Odyssey G7 LC32G75T, get around it by overdriving the pixels. It results in much better dark scene performance but a more noticeable overshoot in brighter areas.

Within each of the three types of LCD we mentioned, other related panel types use the same basic idea but with slight differences. For example, two popular variants of IPS panels include ADS (technically known as ADSDS, or Advanced Super Dimension Switch) and PLS (Plane to Line Switching). It can be hard to tell these panels apart simply based on the subpixel structure, so we"ll usually group them all as IPS, and in the text, we"ll usually refer to them as IPS-like or IPS family. There are slight differences in colors, viewing angles, and contrast, but generally speaking, they"re all very similar.

There"s another display technology that"s growing in popularity: OLED. OLED, or organic light-emitting diode, is very different from the conventional LCD technology we"ve explored above. OLED panels are electro-emissive, which means each pixel emits its own light when it receives an electric signal, eliminating the need for a backlight. Since OLED panels can turn off individual pixels, they have deep, inky blacks with no blooming around bright objects. They also have excellent wide viewing angles, a near-instantaneous response time, and excellent gray uniformity.

OLED panels aren"t perfect, though. There"s a risk of permanent burn-in, especially when there are lots of static elements on screen, like the UI elements of a PC. There aren"t many OLED monitors available, either, but they"ve started to gain popularity as laptop screens and for high-end monitors, but they"re very expensive and hard to find. They"re also not very bright in some cases, especially when large bright areas are visible on screen. The technology is still maturing, and advances in OLED technology, like Samsung"s highly-anticipated QD-OLED technology, are promising.

As you can probably tell by now, no one panel type works best for everyone; it all depends on your exact usage. Although there used to be some significant differences between panel types, as technology has improved, these differences aren"t as noticeable. The two exceptions to this are viewing angles and contrast. If you"re in a dark room, a VA panel that can display deep blacks is probably the best choice. If you"re not in a dark room, you should focus on the other features of the monitor and choose based on the features that appeal to your exact usage. IPS panels are generally preferred for office use, and TN typically offers the best gaming experience, but recent advancements in VA and IPS technology are starting to change those generalizations. For the most part, the differences between each panel type are so minor now that it doesn"t need to be directly factored into your buying decision.

In order to understand this problem, we first need to know the panel type of LCD. At present, the LCD panels are mainly divided into three categories, which are TN, VA and IPS.

TN panel, full name Twisted Nematic (twist nematic), because the production cost is relatively low, so it is the first popular panel in LCD. The advantage of TN panel is that the response time of GTG panel is very fast, and the gray scale response time of GTG is often up to 1ms, which is the lowest among all LCD panels, so many e-sports / game monitors use TN panel.

However, the shortcomings of the TN panel are also obvious, such as less output gray scale, white color, small visual angle and so on. 1080p is the most common resolution in the TN panel, and there are also some 27-inch QHD panels, and the latest panel can do 28-inch UHD. At present, the main manufacturers of TN panels are Samsung display (Samsung Display), LG, Youda Optoelectronics, Qunchuang Optoelectronics, China Picture Tube and so on.

Let"s talk about the VA panel. VA panel full name Vertical Alignment (vertical arrangement), its advantage lies in the contrast, VA panel is the highest contrast of all LCD panels, usually can reach 3000 VA 1, while the contrast of TN, IPS is only about 1000 VA 1, the intuitive feeling of high contrast is that black looks purer and the picture is more layered.

The gray scale response time of VA panel is faster than that of IPS, and some of them even reach the same 1ms as TN, while the visual angle of TN is much better than that of TN, which is consistent with the visual angle of IPS panel, and there is no light leakage problem of VA panel.

Finally, let"s talk about the IPS panel. IPS full name In-Plane Switching (plane conversion), its advantage is that the color performance is relatively good, and the visual angle is also relatively wide, horizontal and vertical visual angle can reach 178°, but the contrast is not as good as VA panel, and the problem of light leakage is also more prominent.

From the above carding, it is not difficult to see that each panel has its own advantages, but also some inherent shortcomings. For example, TN panel is better than fast response time, but the color and visual angle is not good; VA panel contrast is high, but there are still some differences in response time and color; IPS color is good, but there are long response time and light leakage problems.

So which panel to choose depends on the specific requirements, you can"t simply think that IPS must be better than VA, or VA must be better than TN. For example, heavy players of FPS games who value response time can choose the display of TN panel, designers who value visual angle and have certain requirements for color can choose the display of IPS panel, and friends who like to watch some high-contrast and more powerful pictures can choose the display of VA panel.

A thin-film-transistor liquid-crystal display (TFT LCD) is a variant of a liquid-crystal display that uses thin-film-transistor technologyactive matrix LCD, in contrast to passive matrix LCDs or simple, direct-driven (i.e. with segments directly connected to electronics outside the LCD) LCDs with a few segments.

In February 1957, John Wallmark of RCA filed a patent for a thin film MOSFET. Paul K. Weimer, also of RCA implemented Wallmark"s ideas and developed the thin-film transistor (TFT) in 1962, a type of MOSFET distinct from the standard bulk MOSFET. It was made with thin films of cadmium selenide and cadmium sulfide. The idea of a TFT-based liquid-crystal display (LCD) was conceived by Bernard Lechner of RCA Laboratories in 1968. In 1971, Lechner, F. J. Marlowe, E. O. Nester and J. Tults demonstrated a 2-by-18 matrix display driven by a hybrid circuit using the dynamic scattering mode of LCDs.T. Peter Brody, J. A. Asars and G. D. Dixon at Westinghouse Research Laboratories developed a CdSe (cadmium selenide) TFT, which they used to demonstrate the first CdSe thin-film-transistor liquid-crystal display (TFT LCD).active-matrix liquid-crystal display (AM LCD) using CdSe TFTs in 1974, and then Brody coined the term "active matrix" in 1975.high-resolution and high-quality electronic visual display devices use TFT-based active matrix displays.

The circuit layout process of a TFT-LCD is very similar to that of semiconductor products. However, rather than fabricating the transistors from silicon, that is formed into a crystalline silicon wafer, they are made from a thin film of amorphous silicon that is deposited on a glass panel. The silicon layer for TFT-LCDs is typically deposited using the PECVD process.

The twisted nematic display is one of the oldest and frequently cheapest kind of LCD display technologies available. TN displays benefit from fast pixel response times and less smearing than other LCD display technology, but suffer from poor color reproduction and limited viewing angles, especially in the vertical direction. Colors will shift, potentially to the point of completely inverting, when viewed at an angle that is not perpendicular to the display. Modern, high end consumer products have developed methods to overcome the technology"s shortcomings, such as RTC (Response Time Compensation / Overdrive) technologies. Modern TN displays can look significantly better than older TN displays from decades earlier, but overall TN has inferior viewing angles and poor color in comparison to other technology.

Most TN panels can represent colors using only six bits per RGB channel, or 18 bit in total, and are unable to display the 16.7 million color shades (24-bit truecolor) that are available using 24-bit color. Instead, these panels display interpolated 24-bit color using a dithering method that combines adjacent pixels to simulate the desired shade. They can also use a form of temporal dithering called Frame Rate Control (FRC), which cycles between different shades with each new frame to simulate an intermediate shade. Such 18 bit panels with dithering are sometimes advertised as having "16.2 million colors". These color simulation methods are noticeable to many people and highly bothersome to some.gamut (often referred to as a percentage of the NTSC 1953 color gamut) are also due to backlighting technology. It is not uncommon for older displays to range from 10% to 26% of the NTSC color gamut, whereas other kind of displays, utilizing more complicated CCFL or LED phosphor formulations or RGB LED backlights, may extend past 100% of the NTSC color gamut, a difference quite perceivable by the human eye.

The transmittance of a pixel of an LCD panel typically does not change linearly with the applied voltage,sRGB standard for computer monitors requires a specific nonlinear dependence of the amount of emitted light as a function of the RGB value.

In-plane switching was developed by Hitachi Ltd. in 1996 to improve on the poor viewing angle and the poor color reproduction of TN panels at that time.

Initial iterations of IPS technology were characterised by slow response time and a low contrast ratio but later revisions have made marked improvements to these shortcomings. Because of its wide viewing angle and accurate color reproduction (with almost no off-angle color shift), IPS is widely employed in high-end monitors aimed at professional graphic artists, although with the recent fall in price it has been seen in the mainstream market as well. IPS technology was sold to Panasonic by Hitachi.

Most panels also support true 8-bit per channel color. These improvements came at the cost of a higher response time, initially about 50 ms. IPS panels were also extremely expensive.

IPS has since been superseded by S-IPS (Super-IPS, Hitachi Ltd. in 1998), which has all the benefits of IPS technology with the addition of improved pixel refresh timing.

In 2004, Hydis Technologies Co., Ltd licensed its AFFS patent to Japan"s Hitachi Displays. Hitachi is using AFFS to manufacture high end panels in their product line. In 2006, Hydis also licensed its AFFS to Sanyo Epson Imaging Devices Corporation.

It achieved pixel response which was fast for its time, wide viewing angles, and high contrast at the cost of brightness and color reproduction.Response Time Compensation) technologies.

Less expensive PVA panels often use dithering and FRC, whereas super-PVA (S-PVA) panels all use at least 8 bits per color component and do not use color simulation methods.BRAVIA LCD TVs offer 10-bit and xvYCC color support, for example, the Bravia X4500 series. S-PVA also offers fast response times using modern RTC technologies.

A technology developed by Samsung is Super PLS, which bears similarities to IPS panels, has wider viewing angles, better image quality, increased brightness, and lower production costs. PLS technology debuted in the PC display market with the release of the Samsung S27A850 and S24A850 monitors in September 2011.

Due to the very high cost of building TFT factories, there are few major OEM panel vendors for large display panels. The glass panel suppliers are as follows:

External consumer display devices like a TFT LCD feature one or more analog VGA, DVI, HDMI, or DisplayPort interface, with many featuring a selection of these interfaces. Inside external display devices there is a controller board that will convert the video signal using color mapping and image scaling usually employing the discrete cosine transform (DCT) in order to convert any video source like CVBS, VGA, DVI, HDMI, etc. into digital RGB at the native resolution of the display panel. In a laptop the graphics chip will directly produce a signal suitable for connection to the built-in TFT display. A control mechanism for the backlight is usually included on the same controller board.

The low level interface of STN, DSTN, or TFT display panels use either single ended TTL 5 V signal for older displays or TTL 3.3 V for slightly newer displays that transmits the pixel clock, horizontal sync, vertical sync, digital red, digital green, digital blue in parallel. Some models (for example the AT070TN92) also feature input/display enable, horizontal scan direction and vertical scan direction signals.

New and large (>15") TFT displays often use LVDS signaling that transmits the same contents as the parallel interface (Hsync, Vsync, RGB) but will put control and RGB bits into a number of serial transmission lines synchronized to a clock whose rate is equal to the pixel rate. LVDS transmits seven bits per clock per data line, with six bits being data and one bit used to signal if the other six bits need to be inverted in order to maintain DC balance. Low-cost TFT displays often have three data lines and therefore only directly support 18 bits per pixel. Upscale displays have four or five data lines to support 24 bits per pixel (truecolor) or 30 bits per pixel respectively. Panel manufacturers are slowly replacing LVDS with Internal DisplayPort and Embedded DisplayPort, which allow sixfold reduction of the number of differential pairs.

The bare display panel will only accept a digital video signal at the resolution determined by the panel pixel matrix designed at manufacture. Some screen panels will ignore the LSB bits of the color information to present a consistent interface (8 bit -> 6 bit/color x3).

With analogue signals like VGA, the display controller also needs to perform a high speed analog to digital conversion. With digital input signals like DVI or HDMI some simple reordering of the bits is needed before feeding it to the rescaler if the input resolution doesn"t match the display panel resolution.

Kawamoto, H. (2012). "The Inventors of TFT Active-Matrix LCD Receive the 2011 IEEE Nishizawa Medal". Journal of Display Technology. 8 (1): 3–4. Bibcode:2012JDisT...8....3K. doi:10.1109/JDT.2011.2177740. ISSN 1551-319X.

Brody, T. Peter; Asars, J. A.; Dixon, G. D. (November 1973). "A 6 × 6 inch 20 lines-per-inch liquid-crystal display panel". 20 (11): 995–1001. Bibcode:1973ITED...20..995B. doi:10.1109/T-ED.1973.17780. ISSN 0018-9383.

K. H. Lee; H. Y. Kim; K. H. Park; S. J. Jang; I. C. Park & J. Y. Lee (June 2006). "A Novel Outdoor Readability of Portable TFT-LCD with AFFS Technology". SID Symposium Digest of Technical Papers. AIP. 37 (1): 1079–82. doi:10.1889/1.2433159. S2CID 129569963.

IPS displays are highly popular for their eye-catching color and wide viewing angles. In fact, Lenovo now offers more laptops, tablets and monitors based on In Plane Switching or IPS display technology than with the earlier TN (Twisted Nematic) construction – although TN models are still prized by some users, such as hyper-competitive PC gamers.

So, what does an IPS display really deliver? Which laptop and monitor buyers are most likely to benefit from IPS technology? And why do some users still prefer older-style TN displays? Read on for answers to these and other questions.

IPS and TN are different kinds of TFT LCDs (Thin Film Transistor Liquid Crystal Displays). At the simplest level, LCDs rely on the light modulating properties of energized liquid crystals – along with coordinated light filtering polarizers (both behind and in front of the crystals) -- to control what appears on the screen. By applying voltage to each crystal (or not), light is made to pass through the polarizers (or not). When these changes are managed at microsecond intervals, you get smooth moving images.

TN and IPS displays differ in how their light-influencing polarizer layers are aligned. If this sounds too technical, just know that when polarizers are aligned similarly, light can pass through, but when they’re put in different orientations, light is blocked. And when you place liquid crystal molecules between the polarizer layers and apply voltage, interesting things happen:

TN polarizers are aligned perpendicular to each other. Without voltage, the liquid crystal molecules naturally “twist” the light so it can go from a vertically-aligned polarizer, be twisted in the crystals, and then pass through the associated horizontal polarizer. But if you apply voltage (in other words, if you disrupt the crystals’ natural properties), the light no longer gets twisted and the perpendicular polarizer orientations block light from passing through.

IPS polarizers are aligned in parallel, which would normally allow all light to pass through. But again, the resting liquid crystal molecules twist the light to disrupt the normal flow. So IPS displays work in an opposite manner from TN ones. Rather than the application of voltage blocking light, the voltage lets light get through. It prevents the liquid crystals from twisting the light so it can pass through the parallel polarizers as usual.

There’s a lot more to it, of course. But this gives you the general idea of how TN and IPS displays differ. And it’s these differences that give each type of display distinct advantages for specific customers. For example, the parallel polarizer alignment on IPS displays is one reason they can be viewed from extreme angles compared to their TN counterparts. Meanwhile, the way TN displays let light through by default (without applying voltage to disrupt the flow) is one reason TN displays have faster response times and refresh rates than similar IPS models.

Your need for IPS technology depends on how you will use your laptop display or standalone monitor. Here’s a quick run-down of the relative advantages of IPS and TN displays. How does each type match your requirements?

Wider viewing angles: The parallel orientation of an IPS display’s crystals and polarizers make them far easier to see from extreme angles, such as for viewing by large groups. Only those farthest to the side of the display will see any big diminishment in color and contrast.

Greater variety of colors: Most IPS displays feature 8-bit panels (8 bits red, 8 bits green, 8 bits blue), so they can better reproduce the full 24-bit color palette of a typical graphics processor (8 x 3 = 24). Many TN displays have 6-bit panels (6 x 3 = 18) and use extra steps to emulate the full color range.

Improved color accuracy: IPS displays are generally built to meet a higher price point than TN ones and use better backlights capable of generating far wider color gamuts (for example, Adobe RGB versus the older sRGB). The additional hues and shades allow more realistic, true-to-life colors.

One perceived disadvantage of IPS monitors compared to TN ones is their relatively slower refresh rates (the time needed to reconfigure each on-screen image) and response times (the delay when a pixel changes from an active to inactive state). But these delays are measured in milliseconds, so the vast majority of users – say, everyone but advanced PC game players -- will not be impacted. IPS is plenty fast enough for streaming movies, making video calls, and so on.

Faster response times and refresh rates: As stated above, the nature of a TN display makes it faster at refreshing the on-screen imagery and activating/deactivating each pixel. And while the difference is only a few milliseconds (the best TN panels boast response times as fast as 1 ms -- 2-3 ms faster than top-end IPS models), competitive PC gamers typically want the fastest refresh rates and response times.

Lower prices (generally): It’s broadly accepted that a TN display will cost less than an IPS one with equivalent resolution, features, and so on. However, the price difference has narrowed over time, with some IPS monitors now available for $200 USD or less. Still, be wary of IPS displays that seem too inexpensive. Some users complain about so-called “IPS glow” on low-end IPS displays, with the backlight appearing brighter in some parts of the screen than others.

Ready to shop? Lenovo offers a full line of laptops, tablets, standalone monitors, and all-in-ones with different display technologies. Now that you know how IPS and TN displays differ, you’re ready to make your choice.

Display technology has been evolving for more than a century and continues to drive innovations in the electronic device market. IPS technology was developed in the 90s to solve color and viewing angle issues.

IPS display panels deliver the best colors and viewing angles compared to other popular display planes, including VA (vertical alignment) and TN (twisted nematic).

LCDs (liquid crystal displays). IPS changes the behavior of an LCD’s liquid crystals to produce a sharper, more accurate picture. This technique allows IPS displays to deliver a higher quality viewing experience than other screen types like TN or VA.

IPS acts on the liquid crystals inside an LCD, so when voltage is applied, the crystals rotate parallel (or in-plane), allowing light to pass through them easily. By reducing the amount of interference in the light being produced by the display, the final image on the screen will be much clearer.

One of the leading advantages that IPS offer is its ability to deliver wide angles while preserving colors and contrast. This means you can view an IPS screen from nearly any angle and get an accurate representation of the image on-screen.

IPS display screens and monitors offer the best quality in different environments (direct sunlight, low light, indoors, or outdoors) compared to TNs or VAs.

IPS LCDs require about 15% more power than a standard TN LCD. OLED displays require much less power than IPS types due to the fact that they don’t require a backlight. The LCD IPS technology is not the ideal solution if you need an energy-efficient display. You’re better off choosing an OLED or TN TFT for a low-power solution.

Becaus