edge-lit lcd panel brands

LED-backlit LCD, which uses light-emitting diodes for backlighting is a common type of display on televisions and laptops. Unlike pure LED screens these LCDs are not self-illuminating and are reliant on the backlighting for illuminating the display. It is an advancement on the preceding cold cathode fluorescent technology and some manufacturers and retailers may advertise this type of screen as an LED TV.

Edge-lit is a type of screen backlighting that has LED lights lining either the top and bottom edges of the screen or the perimeter of the screen. This form of backlighting differs from others as the screen is not lit from behind, and often produces a more muted effect. An opaque piece of plastic called a diffuser light guide distributes the lighting across the rear of an LCD panel.

Edge-lit LEDs can be individually brightened or dimmed to provide the high degree of backlight control that screened content demands. Edge-lit screens can achieve this in one of two ways:

Direct-lit backlighting uses LED lighting across a television back panel. This form of backlighting initially used Cold Cathode Fluorescent Lamps (CCFLs) before transitioning to LED. The lighting is behind the LCD panel to provide consistent lighting across the entire screen.

Both types of backlighting provide the illumination LED screens required to produce a visible image. The main difference is that direct-lit backlights sit behind the LCD panel to provide the necessary lighting whereas edge-lit screens have LEDs sitting at the perimeter of the screen. Here are some other notable differences:

The first generation of LED backlighting was edge-lit. However, this early form of edge-lit technology caused the development of hotspots on the screen and the overall lighting was inadequate. As LED design became more efficient and effective, Samsung revisited this type of backlighting with a market-leading edge-lit LED television in 2009.

Direct-lit panels use a simple array of LEDs to provide uniform lighting across an entire LCD panel. The adoption of direct-lit screen technology in the 2000s was driven by the availability of white LEDs that could replace existing CCFL technology.

When comparing different models of televisions, you might see the term "edge-lit LED." All LED TVs are a type of LCD TV; the "LED" refers only to the kind of lighting source used to illuminate the LCD pixels in the television. There is more than one way to light the pixels. The two primary technologies are edge-lit and full-array.

In an edge-lit television, the LEDs that illuminate the LCD pixels are located only along the edges of the set. These LEDs face inward toward the screen to illuminate it.

In some poorer-quality edge-lit LEDs, uniform picture quality can be a problem. Because the LEDs are along the edges of the panel, quality declines as you approach the middle of the screen because a uniform amount of illumination is not reaching the pixels further from the edges. Again, this is more noticeable during scenes of darkness; the black along the sides of the screen is more gray than black (and corners can appear to have a flashlight-like quality of illumination emanating from the edges).

Full-array LED televisions use a full panel of LEDs to illuminate the pixels. Most of these sets also have local dimming, which means the LEDs can be dimmed in different regions of the panel while other areas are not. It helps improve black levels, which appear closer to black than dark gray.

In general, full-array LED is a superior technology when it comes to picture quality, but edge-lit sets have one significant advantage: depth. Edge-lit LED TVs can be much thinner than those lit with either a full LED panel or traditional fluorescent (non-LED) backlight. For that reason, most of the super-thin sets you see in stores will be edge-lit.

If you"re looking for the best possible picture quality, you are most likely to find it in a full-array LED display with local dimming. If you are primarily concerned about the appearance of the television and want an extremely thin screen, edge-lit is the style that will fit your needs.

LCD panels are backlit by LED lights, so they rely on a backlight behind the panel to make the picture visible, and the LCD layer can"t prevent all light from escaping out of the screen. This means that even in a black scene, the backlight is still on, and some light escapes, causing blacks to appear gray.

Frame dimming: Frame dimming, or CE dimming on Samsung TVs, is a basic version of local dimming, but it dims the entire backlight instead of zones. Usually found on edge-lit TVs, it causes small highlights to become dim as well. It may improve the contrast a bit, but it"s not very useful for most scenes.

Local dimming features on LED TVs are a way to improve the contrast ratio. Since these TVs consist of LED backlights behind an LCD panel, local dimming aims to turn off, or dim, certain zones of the LED backlight, making blacks look darker and highlights brighter. However, there may be some issues with local dimming on some TVs as it could cause blooming around bright objects or for entire zones to light up when there"s a small object. Overall, most local dimming features on modern TV do an effective job at improving the picture quality in dark scenes, and only some lower-end models will have glaring problems.

The Samsung QN90B QLED is the best TV with an LED panel we"ve tested. It"s an impressive TV with amazing picture quality and a great selection of gaming features. It uses a Mini LED backlight, with way more dimming zones than most LED TVs, which allows for greater control over the local dimming feature for better dark room performance, with less distracting blooming around bright objects. It also gets exceptionally bright, meaning it can handle lots of glare in a bright room.

What"s a backlight? Well, it"s the light source that is situated directly behind the LCD panel of the majority of TVs. It"s what makes the screen glow, what gives bright colors their vibrancy, and increasingly, what gives dark shadows their depth.

There"s a little more to the glowing panel of an LCD TV than you might expect. The LCD panel offers the shape and color components of an image, but it doesn"t actually produce any light of its own. And without light to produce the colors we see and project the image outward to the viewer, an LCD TV wouldn"t be worth much. Enter the humble backlight.

Behind the LCD panel is a backlight, and between the backlight and the LCD panel are usually a few layers of polarized filters, backlight diffusers, and other optical layers designed to turn this collection of tech components into a sharper viewable image.

You"ll have an LCD panel to provide much of the image content, and a backlight behind it to provide the light that makes that LCD panel visible and the colors vivid. But that backlight has undergone a lot of changes over time — several just within recent years. And a lot of the improvements we"ve seen in modern TVs can be traced to the humble backlight.

But with the advent of LCD-based flat screen TVs, the need arose for illumination, and originally that meant cold cathode fluorescent lamps (CCFL), a technology that"s similar to fluorescent and neon lighting. But because these lamps generate heat that can damage a display and aren"t terrible energy-efficient, they"ve pretty much disappeared from today"s TVs.

Instead, they were replaced by one of the biggest innovations in modern TV technology: LED backlighting. With this change, TV manufacturers started calling LCD TVs with LED backlight "LED TVs" to differentiate them from the older CCFL-lit models. But with the last CCFL TVs going off the market a decade ago, it"s just as likely that TV makers have kept the LED nomenclature around to blur the distinction between LCD TVs and OLED panels, which use a very different (and largely superior) display technology.

Edge-lit displays illuminate the LCD panel by setting a row of LEDs along the top and bottom edges of a screen, or ringing the perimeter of the TV frame with LED lights. This light is then distributed across the back of the LCD panel with a special diffuser light guide, a semi-transparent sheet of plastic that allows the light from the LED in the TV bezel to illuminate a larger portion of the display.

It"s a very cost effective way to light a TV, since it uses the least amount of LEDs. It also offers some level of dynamic backlight control for HDR support. On sets that are equipped to do so, portions of the edge lighting strips can be darkened or dimmed to provide deeper blacks, or brightened to accentuate brighter portions of the screen. However, since they don"t directly light the LCD panel from behind, the effect is considerably muted when compared to other backlight technologies.

Direct lit LED backlighting uses LED lighting across the back of the TV, directly behind the LCD panel, providing a fairly uniform amount of light across the screen. It also allows for a brighter picture, since it uses more LEDs, and is able to utilize more of the light coming from those LEDs.

However, an all-white back light alone has its limitations. Because the entire LCD panel is lit uniformly, there"s little to no dynamic range offered by the display.

Toshiba C350 Fire TV (2021 model)The Toshiba C350(opens in new tab) is one of the better Amazon Fire smart TVs we"ve reviewed, but the direct LED backlight is something of a double-edged sword. It"s better and brighter than a basic edge-lit LED backlight, and picture is better as a result, but the lack of local dimming means that – despite the TV"s support for Dolby Vision and HDR10 formats – HDR content just doesn"t look very good.

Local dimming has been further refined with the introduction of mini-LEDs. By shrinking the LED size down to about one-fifth the size – mini-LEDs measure 0.008-inch (200 microns) across – more LEDs can be packed into the backlight panel, and much smaller dimming zones to be used.

Samsung QN90A Neo QLED TVWhen it comes to the several TVs on the market that have mini-LED backlight, the Samsung Neo QLED takes the top spot, holding the top position among the best TVs we"ve reviewed. It"s a great TV for many reasons, but the impeccable backlight and HDR performance of the Samsung QN90A Neo QLED TV(opens in new tab) makes it one of the best LCD TVs we"ve ever seen.

OLED displays have individual pixels that light up without the need for a separate illumination source, creating a self-emissive display panel that doesn"t need any sort of backlight.

Most television companies, as well as sellers, misguide consumers by saying that this particular TV is not LCD but LED. So, first of all, we need to understand that all TVs are basically only

LCDs. What we refer to as LED is simply an update to the existing LCD panels. The panel technology is the same, however, the backlight is entirely different. Those LCDs that use LEDs as a light source are generally termed as LEDs. In short, a LED-backlight is a replacement for the uniform CCFL (Cold Cathode Fluorescent Light) backlight that previously gave LCD TVs its brightness.

Initially, there were only CCFL-backlit LCDs, but with advancement in technology, these CCFL were replaced by LEDs, as not only they dramatically reduced power consumption by over 40 percent compared to conventional CCFL-backlit LCDs, we got more control over the image quality by modulating these individual LEDs.

In the LED-backlit LCDs, LED lights can switch on and off individually, which allows the image to have greater contrast, bright whites and deep black in the same image. Thus, producing a superior picture when compared to CCFL-backlit LCDs. LCD TVs with LEDs also offer better response time in comparison to CCFL-backlit LCDs.

In the traditional LCDs, the CCFL lights were spread all across the surface behind the display screen, but there was no control over them. It means that when we switched on our TV, the entire surface behind the screen used to get illuminated by these CCFL lights that were always ON, and we were unable to control their dimming in specific areas of the screen.

Because of this, even the dark part of the picture used to be illuminated like the rest and we were unable to achieve images with convincing blacks, as light passed through the dark part of the picture and made it appear grey. In other words, the contrast of CCFL-backlit LCD panels isn’t very good. However, a plasma TV doesn’t have this problem as each pixel can light up or switch-off according to the demand of the picture.

Now coming to LCDs that use LEDs as the source of illumination, there are basically three types. One is Full-array backlighting, another is Edge-lit backlighting (ELED) and third is direct-lit LED backlights (DLED).

The term full-array is used where LEDs cover the entire back-side of the LCD panel. Full-array TVs are high-ends TVs that are heavier and often thicker, but they provide better picture quality as all parts of the screen are evenly backlit. They offer the most effective local dimming, as the LEDs are more in number and are spread over the entire back surface of the panel. The independent dimming of each LED in these TV sets helps in achieving perfect blacks. But, as they are costlier to manufacture, they are rare.

This technology allows the designing and manufacturing of exceptionally thin TV sets. Edge-lit sets also have a cost-benefit over direct, local dimming versions (DLED) as fewer LEDs are used in them. Because of which, they are power efficient too.

Direct-lit LED backlights are an offshoot of full-array backlighting, though they use significantly fewer LEDs across the back of the panel. In this technology, several rows of LEDs are placed behind the entire surface of the screen.

As the LEDs are behind the LCD panel in DLED TVs, dual modulation works far more efficiently and the TVs can have better overall brightness and contrast. Using a feature called local dimming, the LEDs are divided into a number of zones that can be individually controlled, so some portions of the backlight can be dimmed while other remain illuminated.

Though different brand TVs might be using the same DLED or ELED backlighting, their image quality might differ considerably depending on how many lights are used and how they are aligned. In some budget Edge-lit TVs, LEDs are aligned on only one side, either upper or lower edge of the TV panel, while others might have LEDs on both upper and lower edges of the panel. The high end TVs might even have a row of LEDs on all four edges of the panel. Some manufacturers use both Edge and Direct LED systems for LCD TVs. The best professional monitors use direct LEDs.

Though bigger brands like Sony, Samsung and LG also prefer EDGE-lit LED backlighting in their TVs, they complement it with some of their indigenously formulated technology to enhance the picture quality.

TV manufacturers lay more stress on producing TVs with ELED technology as it not only cut down upon their expenditure but allows them the liberty of producing ultra-slim TV sets that can appeal the masses with their aesthetically designed panels.