3.3 v lcd display pricelist

ERM1602FS-6 is 16 characters wide,2 rows character lcd module,SPLC780C controller (Industry-standard HD44780 compatible controller),6800 4/8-bit parallel interface,single led backlight with white color included can be dimmed easily with a resistor or PWM,fstn-lcd positive,black text on the white color,high contrast,wide operating temperature range,wide view angle,rohs compliant,built in character set supports English/Japanese text, see the SPLC780C datasheet for the full character set. It"s optional for pin header connection,5V or 3.3V power supply and I2C adapter board for arduino.

It"s easily controlled by MCU such as 8051,PIC,AVR,ARDUINO,ARM and Raspberry Pi.It can be used in any embedded systems,industrial device,security,medical and hand-held equipment.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and Development Kit at the bottom of this page.

At first I couldn"t get it to work, then as I dug around the arduino.cc tutorials I noticed in the graphics they had that the board was rotated 180° from how I was attempting to use it. I had interpreted the - and + symbols on the board as being ground and Vcc respectively, going off of Peter Fleury"s webpage linked in the article, when in fact they were actually the backlight LED cathode and anode (respectively). For anyone who might have less technical knowledge than me, I"ll simplify this paragraph by saying that the LCD screen"s letters rightside-up have the pins above them, and said pins are numbered increasing left to right, so that if you number the screw-hole closest to the pins as 0, the rest work out correct in accordance with Peter Fleury"s page, with the addition of pins 15 and 16 as backlight LED + and - respectively

Also I"m curious to know how consistent the contrast-voltage-to-actual-contrast ratio is so I"ll share that my LCD screen works close to best with a 0V - 820Ω - Vcontrast - 3300Ω - 3.3V voltage divider setup.

Also also, when Sparkfun says you"ll "need ~11 general I/O pins to interface to this LCD screen" that doesn"t account for the fact that you mostly don"t need to "read" data from an LCD display and that it works fine for everything I"ve tried it out with in 4-bit mode, so you really only need Register Select (R/S pin 4), Enable Clock (E pin 6), and Data 4-7 (pin 11, 12, 13, 14), with Read/Write pin 5 driven to ground which adds up to 6 pins, 8 including ground and 3.3V. I"ve found it quite useful that it can be run entirely over a spare ethernet (8P8C RJ-45 tested with Cat5e) cable with the proper breakout boards.

Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Please visit www.P65Warnings.ca.gov for more information. This item was manufactured prior to August 31, 2018.

This website is using a security service to protect itself from online attacks. The action you just performed triggered the security solution. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data.

The CFA533-***-KC series is a 16x2 I2C LCD with keypad. The I2C interface allows you to use just two lines (SDA & SCL) to have bi-directional communication with the I2C LCD. Other devices can also share those two I2C control lines with the LCD. Only 4 wires are needed to connect this I2C LCD: power, ground, SDA (I2C Serial DAta) and SCL (I2C Serial CLock).

The CFA533 can run on 3.3v to 5.0v directly, with no changes needed, so you do not need to do any level translation between your embedded processor and the I2C LCD. Simply power the CFA533 from the same supply as your processor and the I2C signal levels will match up.

Using only one address on your I2C bus, you can add all the elements that you need for your front panel. The CFA533 I2C LCD can also read up to 32 DS18B20 digital temperature sensors, giving you an easy way to integrate temperature sensing over the I2C bus. No additional firmware or pins are needed on the host system.

This CFA533-YYH variant shows crisp, dark letters against a yellow-green backlit background. The keypad is backlight in a matching yellow-green. Since the LCD is a backlit positive STN, the CFA533-YYH I2C LCD is easily viewable in all lighting conditions, from direct sunlight to a completely dark room.

Girgaon, Mumbai whats app number 9819869583 //No. 85, 3rd Floor, New Hanuman Building, Shamrao Vithal Marg, Lamington Road, Girgaon, Mumbai - 400007, Dist. Mumbai, Maharashtra

Mumbai 23, Ground Floor, Gandhi Bhavan, Chunam Lane,Lamington Road, Grant Road East Chunam Lane, Lamington Road, Mumbai - 400007, Dist. Mumbai, Maharashtra

Grand Road (East), Mumbai 7/16, Ground Floor, Kamat Building, Shamrao Vitthal Lane, Lemington Road, Grand Road (East), Mumbai - 400007, Dist. Mumbai, Maharashtra

Kandivali, Mumbai I/1103, 11th Floor, Agarwal Nimit Tower Subh Shanti Complex, M G Road Kandivali West,, Kandivali, Mumbai - 400067, Dist. Mumbai, Maharashtra

AOur production quality follow ISO9000 standard system, stable design team,22 years experience of QC team and strictly quality control system guarantee the production quality. accept third part inspection,we have mechanical checking,display checking,high&low temperature storage&operating test during high humidity condition,EMC test(optional) for every design .

0.91 inch 128×32 OLED LCD Display Module. IC I2C DC 3.3V 5V For Arduino PIC: This mini OLED display module is equipped with an SSD1306 chipset and 128X32 white or blue color display. On-board standard IIC serial communication interface with 3.3V-5V wide voltage input enables you to connect it with the MCU development board easily to develop your OLED display projects.

Innolux is one of the most professional LCD screen manufacturers in the world,belongs to Foxconn Group.Innolux was founded in 2003 and went public in Taiwan in 2006. In March 2010, its merger with Chi Mei Optoelectronics and TPO Displays marked the largest merger in the history of the panel industry.