tontec 7 raspberry pi lcd touch screen display price

When you want to have an easier time of connecting to different media and selecting it, a single-board computer is an efficient option. The Raspberry Pi single-board computers work with a variety of peripheral devices, including LCD display modules with touchscreens. On eBay, you can find a variety of sizes and features of affordable Raspberry Pi touch screen units to pair with the single-board computer for enjoying your favorite media.What are some features of Raspberry Pi Touch Screen modules?

Automatic power off: If the touchscreen is not used within 10 minutes, it automatically powers off. This time can be adjusted to turn off in less or more time.

Signal support: It accepts EGA, SVGA, WXGA, VGA, SXGA, and UXGA video signals from the computer.What are the sizes of Raspberry Pi touch screen modules?

The Raspberry Pi touch screen modules are available in sizes of three to seven inches when measured on the diagonal. Their frames can be set up in a vertical or horizontal orientation for viewing in a portrait or landscape setup. The stands for the touchscreens can also be angled for easier use and viewing. See the manufacturer site for details.What is the compatibility of a Raspberry Pi display module?

The following are compatibility options for a Raspberry Pi touch screen display module:USB: They can display the information that is stored on a removable USB drive plugged into the Raspberry Pi computer.

Consider the following features when you are shopping on eBay for a new or used Raspberry Pi touch screen:With computer case: Some have a case for holding both the computer and the display in one unit.

Frequently Asked Questions About Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board in INDIA

Where can I buy Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board online at the best price in the INDIA?

desertcart is the best online shopping platform where you can buy Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board from renowned brand(s). desertcart delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

Is Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board available and ready for delivery in INDIA?

desertcart ships the Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board to and more cities in INDIA. Get unlimited free shipping in 164+ countries with desertcart Plus membership. We can deliver the Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board speedily without the hassle of shipping, customs or duties.

Is it safe to buy Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board on desertcart?

Yes, it is absolutely safe to buy Tontec 7 Inches Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 with Touchscreen Kit HDMI VGA Input Driver Board from desertcart, which is a 100% legitimate site operating in 164 countries. Since 2014, desertcart has been delivering a wide range of products to customers and fulfilling their desires. You will find several positive reviews by desertcart customers on portals like Trustpilot, etc. The website uses an HTTPS system to safeguard all customers and protect financial details and transactions done online. The company uses the latest upgraded technologies and software systems to ensure a fair and safe shopping experience for all customers. Your details are highly secure and guarded by the company using encryption and other latest softwares and technologies.

Limitations : For products shipped internationally, please note that any manufacturer warranty may not be valid; manufacturer service options may not be available; product manuals, instructions, and safety warnings may not be in destination country languages; the products (and accompanying materials) may not be designed in accordance with destination country standards, specifications, and labeling requirements; and the products may not conform to destination country voltage and other electrical standards (requiring use of an adapter or converter if appropriate). The recipient is responsible for assuring that the product can be lawfully imported to the destination country. When ordering from Ubuy or its affiliates, the recipient is the importer of record and must comply with all laws and regulations of the destination country.

Have you ever envied your friends" sweet touch screen systems in their car? Do you look at the dash of your old and decrepit 1992 Isuzu Rodeo and dream of having a slick computer system in your car? Well, your in luck. This Instructable will be your guide on building a system that is low cost and easy to build; it doesn"t even require special tools.

The goal of this Instructable is to create a easy-to-build car computer based on the Raspberry Pi. It does not require special tools and very little knowledge of the Raspberry Pi. I chose not to use advanced tools like 3D printers or laser cutters because, while many do have access to these machines, I have been turned off of projects in the past for using such "out of reach" resources.

The CarPC runs off of a Raspberry Pi Model B running Xbian, a version of XBMC made for the Pi. The touch screen is resistive which, while not ideal, keeps cost down and is easily available through Amazon. It has the capacity to play music, watch videos, look at pictures, play games, and much more.

Raspberry Pi OS provides touchscreen drivers with support for ten-finger touch and an on-screen keyboard, giving you full functionality without the need to connect a keyboard or mouse.

The 800 x 480 display connects to Raspberry Pi via an adapter board that handles power and signal conversion. Only two connections to your Raspberry Pi are required: power from the GPIO port, and a ribbon cable that connects to the DSI port on all Raspberry Pi computers except for the Raspberry Pi Zero line.

approx. ...6 hours total print time/ top piece or bezel screen holder with ribbon cable passage bottom hold 2 pcb boards Case to contain the 7" touch screen and 2 circuit boards Print Settings Printer: Prusa I2 Rafts: No Supports: No Resolution: 300

UPDATE1: Fitted to actual screen from https://grabcad.com/library/innolux-7-tft-lcd-at070tn83v-1. Anyway i had to fix bezels and size. Mine is 100x165 mm.

UPDATE1: Fitted to actual screen from https://grabcad.com/library/innolux-7-tft-lcd-at070tn83v-1. Anyway i had to fix bezels and size. Mine is 100x165 mm.

I have printed an excellent Tontec 7 inch LCD Panel Assembly (http://www.thingiverse.com/thing:721186) and designed pushbutton caps and spacers for the button PCB so buttons are kept at necessary distance for the enclosure. Here is my complete make...

I have printed an excellent Tontec 7 inch LCD Panel Assembly (http://www.thingiverse.com/thing:721186) and designed pushbutton caps and spacers for the button PCB so buttons are kept at necessary distance for the enclosure. Here is my complete make...

A case for a 7" LCD display (destined for the trashcan) with a cheap (chinese) controller board. This started as a test whether the board actually worked with this type of display, and additionally if i could fit all parts in a minimal case. The...

This is a case for a 7 inch LCD screen, this one right here: https://www.amazon.ca/gp/product/B071X8H5FB/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 There are other cases out there but I wanted something that used less material and didn"t take...

A case for [7-inch HDMI/VGA LCD module](https://www.aliexpress.com/item/7-inch-N070ICG-L21-IPS-LCD-screen-display-Control-Driver-board-HDMI-VGA-2AV-1280x800-tablet/32338411917.html?spm=a2g0s.12269583.0.0.74037a7cQFkUGe) that can take up to 1920x1080...

(Update 3/8/2019) A new version is posted here (Update 1/21/2019) Added a desktop foot. A case for 7-inch HDMI/VGA LCD module that can take up to 1920x1080 resolution (with auto scaling - the native resolution is 1280x800). This case supports VESA...

Enclosure for Alomejor 7 inch LCD TFT Display 1024600 HDMI VGA Monitor Screen Kit for Raspberry Pi 3/2 https://www.amazon.com/gp/product/B07VSG29J2/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1 Should be compatible with Adafruit HDMI 4 Pi: 7"...

HDMI/VGA/2AV+Reversing Driver board + 7inch AT070TN90 800*480 lcd display for sale on ebay.http://www.ebay.com/itm/HDMI-VGA-2AV-Reversing-Driver-board-7inch-AT070TN90-800-480-lcd-display-/180974436891 My printer has a small envelope so I cut the...

this is a simple case for the commonly found 7" LCD screen with cutout for connections to controller for raspberry pi or similar single board computers.

1-7 inch keyboard https://ko.aliexpress.com/item/453497000.html 2-raspberry pi 4 3- LCD 7 inch raspberry pi 4-powerbank 20000 add solidwork files I make this case with split parts, because my printer is mini

Case, which was made for Waveshare 7" HDMI LCD with touchscreen (http://www.waveshare.com/7inch-HDMI-LCD-C.htm). Hope it will be useful not for me only )

This is a case for the HT1621, 7 segment LCD"s, Sold in the uk by Hoby Components for just £3.99. https://hobbycomponents.com/newproducts/1001-ht1621-6-digit-7-segment-lcd-module The hobby components web site has a forum with the arduino code on it...

CAUTION: Be careful when removing the LCD board from the black HC Maker 7 control box. There are live mains voltage terminals inside the box so please make sure you unplug the power lead from the wall before you open the box. IT IS NOT SUFFICIENT TO...

If you like the projects I work on check out my YouTube channel at: https://www.youtube.com/channel/UCgItLzb2PnHYKeNAFSx0jpA This is the 7" monitor case by swehacker. The standoffs were detached from the model, and that"s repaired in this remix. I...

Case for official LCD 7" with stand. You need to purchase a tape longer than that attached to the LCD (fits the standard tape from the Camera) Pin can normal connect or solid. ...

43.13US $ 28% OFF|Original 7"Inch Raspberry Pi LCD Touch Screen Display TFT Monitor AT070TN90 TouchScreen Kit HDMI VGA Input Driver Board Set|touch screen|hdmi display monitortouch 7 - AliExpress

2) Log into the command line interface for Raspberry Pi（Initial user name: pi, Password: raspberry）, Get the latest drive from GitHub (the raspberry pie needs to connect to the Internet), Execute the following commands:

init = <0x10000b0 0x0 0x1000011 0x20000ff 0x100003a 0x55 0x1000036 0x28 0x10000c2 0x44 0x10000c5 0x0 0x0 0x0 0x0 0x10000e0 0xf 0x1f 0x1c 0xc 0xf 0x8 0x48 0x98 0x37 0xa 0x13 0x4 0x11 0xd 0x0 0x10000e1 0xf 0x32 0x2e 0xb 0xd 0x5 0x47 0x75 0x37 0x6 0x10 0x3 0x24 0x20 0x0 0x10000e2 0xf 0x32 0x2e 0xb 0xd 0x5 0x47 0x75 0x37 0x6 0x10 0x3 0x24 0x20 0x0 0x1000036 0x28 0x1000011 0x1000029>;

gpio = "/fragment@1:target:0", "/fragment@2/__overlay__/tft35a@0:reset-gpios:0", "/fragment@2/__overlay__/tft35a@0:dc-gpios:0", "/fragment@2/__overlay__/tft35a-ts@1:interrupt-parent:0", "/fragment@2/__overlay__/tft35a-ts@1:pendown-gpio:0";

fixup = "/fragment@2/__overlay__/tft35a@0:pinctrl-0:0", "/__overrides__:speed:0", "/__overrides__:txbuflen:0", "/__overrides__:rotate:0", "/__overrides__:fps:0", "/__overrides__:bgr:0", "/__overrides__:debug:0", "/__overrides__:swapxy:0";

init = <0x10000b0 0x0 0x1000011 0x20000ff 0x100003a 0x55 0x1000036 0x28 0x10000c2 0x44 0x10000c5 0x0 0x0 0x0 0x0 0x10000e0 0xf 0x1f 0x1c 0xc 0xf 0x8 0x48 0x98 0x37 0xa 0x13 0x4 0x11 0xd 0x0 0x10000e1 0xf 0x32 0x2e 0xb 0xd 0x5 0x47 0x75 0x37 0x6 0x10 0x3 0x24 0x20 0x0 0x10000e2 0xf 0x32 0x2e 0xb 0xd 0x5 0x47 0x75 0x37 0x6 0x10 0x3 0x24 0x20 0x0 0x1000036 0x28 0x1000011 0x1000029>;

Kernel command line: bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=tty1 console=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo

[ 44.756917] fb_ili9486 spi0.0: fbtft_write_spi(len=15360): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...

I"m using it to run a lighting and irrigation system for my house. The color graphical interface allows me to use BMP images of my house and yard for control screens, and its built into an enclosure set into the wall for a slick professional look. I even put an access from the backside of the wall for wiring it without having to remove the Pi or the touchscreen.

Great responsiveness, inexpensive, can"t beat 10-finger multi touch! The python demos are really neat, too. Only gripe is that the screen isn"t oleophobic, but for the price I"ll take it!

This was easy to install and it looks good. The Touchscreen is responsive and clear, but you might want to use a stylus. The only issue i had is finding a case for it. You"ll want to get one right away, unless you have a 3D printer to make one yourself. The screen is really thin, so I didn"t want to carry it around without some protection. Overall, it"s a great touchscreen, especially for the price, and I like that it is Raspi-branded.

I purchased 5 touchscreen. Two before and three in January. Touch and display quality is superb. After two-three month of use (no rough use; handled with care), display LCD and front touchpanel (black bezel) break apart. They both are connected using a thin double sided tape. I was planning to use in industrial environment but after such issue, I dropped my plan to use it in industrial environment.

Five of two displays are not in good condition. First display"s touch-panel and display LCD was break apart after two-three month. The second among five displays had another issue. Display LCD was mounted slightly right side of the touchpanel. Once you power-up display, it is easily be seen that LCD panel was a bit off-side. The other display"s screen guard having so many scratches on them which seems mishandling.

I got a couple of these for several RPi projects that Im developing and they are working amazingly well for the application. If these fit your application needs I wouldn"t hesitate to recommend them.

This screen worked right out of the box! Touch worked great with my new pi 3! However aside how fragile the (non functional) edges are, the only real issue I see is upon shutdown of the pi... The screen goes through a series of screen washes/whiteouts and never really shuts off.. I have to pull power to get it to turn off.. I"ve even tried usb/provided jumper wires.. And both results in the same thing. Not sure if this an issue per se, but it is bothersome.. I can just turn the unit off, I need to unplug it too..

I am using Raspberry Pi 3. The display came up with no problems. I am just waiting for the Smarti Pi Touch enclosure (pre-ordered after the Kickstarter project closed) before continuing to work with it.

Basically, it "does what it says on the tin". It"s bright, relatively responsive and has acceptable color. Haven"t played much with the touch screen part of it yet, but very pleased so far!

The only question(s) that I have are regarding what sort of additional processor power is inside the screen, and whether powering it from the micro-usb connection whilst also bridged from the RPi3 is an issue (it hasn"t hurt anything, yet!).

I WAS DISAPOINTED THAT THE UNIT DISPLAYS EVERYTHING UPSIDE DOWN. I HAD TO USE THE LCD_ROTATE=2 COMMAND IN CONFIG.TXT TO FIX IT. THE INITIAL BOOT IS STILL UPSIDE DOWN BUT I GUESS AFTER IT READ THE CONFIG.TXT, IT FLIPS. SHOULDN"T IT COME STANDARD RIGHT SIDE UP?

Hmmm, it should, and this isn"t an issue we"ve seen before. I would suggest getting in touch with our Tech Support team, they should be able to help you out.

With so many, phone and tablets that have hi res screens, this is disappointing. It does what it"s supposed to, but has a retro look. Non techy relatives are not impressed.

The must annoying feature is the bright white screen when it loses signal as the OS shuts down. The touch input is inconsistent as input. I was using the I2C for a device was not able to get it going on the alternate I2C, but fortunately the required clock and data are on the DSI cable ... wasted hours finding that out. An OLED display, higher res, and lower current draw would be really nice in the next version.

I forgot to check that this LCD touchscreen don"t have a case. Much better that you have a notification (e.g. recommending the user to purchase also a case) when purchasing this kind of product. But thank you for this product, I will purchase again soon.

The only minor drawback that everyone should be aware (which is to be expected, honestly) is that the display draws quite a noticeable amount of current. The SmartiPi case comes with an splitter USB cable for the power source, but if you expect to use that, be prepared with a (very) beefy power supply, else you"ll get the thunder icon on the screen all the time and a very reduced performance (Just discovered that the RPi3 reduces its own clock when power is low).

I currently power this with a separate 1.5Amp supply for the screen and a 2Amp supply for the RPi3 and everything works just nice. This totals to a whopping 3.5A, which may be overkill, but keep that in mind as a reference.

I am impressed with this screen, I also got the mating case (SmartPi Touch) and it assembled nicely. With the separate case, the included jumpers and cable are not needed. The PCB was already attached with the standoffs. The packaging was super! The screen is slightly larger than 7 inches. I measured it as 7 5/8" wide X 4 3/8 high with a diagonal measurement of 8 9/16.

This official Raspberry Pi 7" touchscreens now come with the display controller already connected and mounted to the back of the display. You still need to be careful pulling forward the small black tab ends that connect a ribbon cable to the RPi.

I bought the companion enclosure as well. This Touchscreen works exactly as described. I am very pleased with the display. I ended up using a mouse anyway as the icons (while clear are very tiny) and selection areas are a bit small for fat fingers.

I connected it to a Raspberry Pi 3 B running Stretch and it seems to be working perfectly. I had been previously driving a VGA monitor from HDMI through an adapter. The RPI 7" screen started up just fine without changing or installing anything with the OS.

I connected it to a Raspberry Pi 3 B running Stretch and it seems to be working perfectly. I had been previously driving a VGA monitor from HDMI through an adapter. The RPI 7" screen started up just fine without changing or installing anything with the OS.

Based on other comments here and looking at one of these at a maker space, I bought the smartipi touch case for this; it"s strongly constructed and works great. Only issue was that I"m using this with a model 3 B+, and that takes a different door on the back than comes with the case (this is being fixed by the smartipi folks, but I don"t know the logistics of getting their new cases into Sparkfun)

I have tried other touch screens for the Raspberry Pi. They had complicated assembly and were very difficult to get them to work. This unit was easy to install and get working, is very nice looking. I am very Happy with it.

Right out of the box it worked. Didn"t even have to do anything to the RPi (in fact, both were taken out of the box at the same time, connected, and worked on the first power up). Screen quality is good for price. Also ordered the "SmartPi Touch" case which holds everything together very nicely.

Ordered it, a Raspberry Pi 3 B+, and a power supply. (Had a mouse, keyboard, and uSD on hand.). It came a couple of days ago, and I put together yesterday. Had noticed in the documentation that there"s a micro USB power input, and a standard USB output. In the configuration where the power supply is plugged directly into the Pi and the LCD interface is powered via a USB cable plugged into one of the Pi"s USB ports to the LCD"s micro USB, the LCD won"t light up at all. When the power supply is plugged into the LCD controller board and the USB cable connects power to the Pi, I get "low voltage" warnings (yellow "lightning bold"). When I use the provided F/F jumpers, it works fine, but this will cause problems plugging in other "hats", as well as clearance problems. (In my application, separate power supplies would be a BIG PROBLEM.) BTW, I checked with two different USB cables, and got the same problems as well as when I tried an Adafruit 5.25V power supply. (I was about to try a second RPi3B+ when the original one stopped booting. Fortunately I had another that I"d been using as a "pass-around" sample at talks, and fortunately when I tried it, it still worked, so now the "dead" one will be passed around!) Also, it could prove really useful to know what size those mounting screws are in case they get lost! Ace Hardware recently opened a new store about half a mile from my house!

The screen is portable enough to take with you and the Pi will use it with no configuration change when it"s powered up. Used it to set up several Raspberry Pis in a remote lab. Touch screen is nice but bring along a keyboard if you have to do any setup work. One thing to make it better, replace the jumper wires with a ribbon cable connected to 1x5 and 2x2 pin headers.

I have a Raspberry Pi in each room of my home and they run a Kiosk interface for home automation, cameras and more. I"ve tried some cheaper ones and none have survived. (I"m hard on equipment) I haven"t managed to break one of these yet.

Got a PI3+, 7" touchscreen and SmartPI case for manufacture test. I put these together and booted the latest Raspbian. The LCD and touchscreen connect to the display connector using a short FPC cable. The display booted and the touch screen just worked out of the box. There were some nice but not well documented improvements. They provide a Y USB cable to power both the PI and the LCD. This is a cleaner solution than the jumper wires they provide.I"m not a big fan of using lego blocks in a industrial environment but the case went together easily and does a decent job of protecting the display and the PI. Some reported a inverted display issue but that seems to have been resolved.

A truly plug-and-play display for the Raspberry Pi. Does not steal any additional extension connector pins if you power it with a USB power supply and leaves the I2C1 interface available for other devices.

Big enough for somewhat squinting actual Raspberry PI development and computer work, but really shines for touch screen optimized large button control panels.

You can just install a Pi3 or 4 on the back, but with a 4 you really need some additional airflow. The SmartiPi Touch 2 enclosure works better. https://www.sparkfun.com/products/16302

It works fine, no glitches, no problems, no hair pulling moments. Once electrically connected to my RPi 3B+ it"s good to go. I run it with the "lite" version of the Raspberry Pi OS with only xorg drivers installed, no full desktop or windows manager, as part of an in-the-field project with a HQ camera attached. My only complaint is the ribbon cable could stand to be about 6 inches longer.

It works great, the colors are beautiful, and finger touch works fine. What I like most is that the Raspberry Pi GPIO pins are all still available - except for one +5v pin and one Ground pin. Both are redundant (i.e. others are available). So, this is not an issue at all. I also like that data connects to the Pi via the IPS ribbon cable. Another thing I like is that power connects to the Pi via two jumper wires. The Pi is fussy about its power supply voltage. So, the jumper wires are better because they are heavier gouge than a small PCB trace.

I connect a Pi v4 and put the whole thing in the SmartPI Touch 2 case from Sparkfun and now it looks pretty professional. Make sure you use a good power supply.

Where is the documentation? This thing is so poorly documented it"s almost a joke. The whole point of the RPi ecosystem is to enable Makers and learning about electronics, so why isn"t this fully documented?

I used this to build a portable utility/testing device for my company. It works fantastic with the SmartiPi Touch Pro Case on Amazon. The touchscreen functions great, only thing is you can"t register mousedown and mouseup events in Chromium (only click). Other than that it"s great!

I got it working the first try, easy to follow instructions. Trying to learn Kivy with Python for touch screen programming, That"s a lot more difficult.

It"s bright, clear, good color rendition. Touch input is responsive and accurate. Trivial to assemble and get going. Like the multiple power options. Would buy again.

Raspberry Pi touchscreens is used for designing projects that limit the use of external input devices like keyboard or mouse. They can be used to create systems in which the hardware is perfectly embedded within one device.

Today we cover some of the best Raspberry Pi touchscreens that are available in the market. Let us know your favourite raspberry pi touchscreens in the comments section.

This Raspberry Pi touchscreens comes with zero documentation, hence requires technical understanding for operation and as a result, greater headache. The unit also does not come pre-assembled. Good for hobbyists and DIY enthusiasts. Software is easy but the stand is wobbly and unstable.

The capacitive touch screen measures 7 inches and is able to sense 10 fingers simultaneously. The kit comes with an adapter, ribbon cable, screws and jumpers.

The pixels in width were larger than the length hence causing the objects to appear a little smashed. The resolution was small too. The bezel surrounding the screen was wide in width where otherwise it could have been made as thin as possible. Nothing bad in it. It just looks a bit untidy. The backlight timeout blanks the page until you touch it again.

3.5 inches LCD display that comes in a kit and includes a clear transparent cover case. Useable with Raspberry Pi model B (3,2). There is a tutorial page to setup and make the LCD work.

The problem of setting up the work screen prevails with nearly all the Raspberry Pi’s LCD’s. Hence they need to be patiently setup with required support from the customer service office if required. The LCD works ‘OK’ after the setup. Small screen with poor resistive touch with no easy setup. But beats in terms of price. Slow refresh rates with no instructions makes it challenging. After upgrading to “Jessie” OS, it worked faster with out of the box touch screen digitizer.

It has a 3.5 inches resistive touchscreen with Serial Peripheral Interface. Compatible with Raspberry Pi 3 B RPi 2B/B+/A+ /A/B/Zero. Heat sinks come with them.

Touch screen works fine and as long as you get/follow instructions from someone its fine. (Refer to the customer support/user reviews for help). The case comes a little cheap and fragile. Fairly many problems with the case and hardware interface.

Eletrow gives a high definition multimedia interface monitor with a 5 inches high definition display. The LCD is a thin film transistor for Raspberry Pi 2B,B+ and 3B. A good alternative for those seeking a bigger display. It has a faster response and full color display. And can be used as a portable monitor.

The power requirement is low and it is USB powered. The system needs some installation and setup to start working. For those facing problems, must refer to user reviews about installation. The screen is bright and crisp. The viewing angle might produce a little pixelation effect.

Kuman’s comes with a 3.5 inches LCD display and resistive touch screen (Pressure applied to the surface of the display by a finger causes the layers to touch each other which completes the electric circuit and tells the system where the user is touching).

The screen is sharp and clear with vibrant text. The touch screen works well and comes with touch pen for precise input. A few hand problem starting up the LCD display (Must refer to user reviews and customer support if you are facing this problem).

You can also make such purchases that fit the Pi right with the LCD screens. The touch screen also needs to be calibrated once you set up the system. The system also doesn’t comes with cables.

Display size is 3.5 inches.Compatible with Raspberry Pi 2 model B and Raspberry Pi B+. Resolution is480*320, 65K color, 16 bit.Transmits data through SPI.

Customers find this pretty great because of case which “is a nice companion to the screen as the screen also doubles as the top cover. The assembly was easy and the plastic and tape came off with no resistance.”

“Top notch display screen for your Raspberry Pi at a great price. Also it’s not just for you Pis, it could be used on any HDMI system. I plugged it into my Win 10 laptop as soon as I got it to check that it was running. Windows 10 recognized it immediately to include the touch abilities of this screen.” – Amazon

“I bought this to use with a Raspberry Pi. However, I tested it with a few other things, just to play around with it. It works fantastically. So far, I have not been able to find a case that I like for it yet, so you will see in the photos, I temporarily used the box it came in to make an enclosure for both the screen, and my rPi. It’s actually pretty nice, and convenient to use this way (for now).” – Amazon