nokia 5110 lcd module supplier

The name NOKIA5110 itself is enough to explain its origin. Yes of course !!! this LCD module was used in old Nokia 5110 and 3310 cell phones. Now its been widely used by hobbyists for graphics, text etc.

Though it’s an industrial module, this LCD display is extremely easy to use. The Nokia 5110 is a basic graphic LCD screen for lots of applications. It was originally intended for as a cell phone screen.

This Nokia 5110 LCD Display Module is mounted on an easy to solder PCB. The Nokia 5110 LCD Module uses a Philips PCD8544 LCD driver, which is designed for mobile phones.

Nokia 5110 LCD Display Module is a low-cost monochrome LCD module comprised of 84 X 48 pixels that can be used to display rich graphics and text content. This module is a revision that accepts 3-5V input. So no extra level shifter is needed.

It uses the PCD8544 controller, which is the same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller or driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.

Many devices that can be used with an Arduino, require a power supply of 3.3V. This is also the case with the Nokia 5110. The best way to deal with 3.3V devices is to take an Arduino Pro, which can run on 3.3V.

Thanks to the internal clamp of the PCD8544 we can use a very simple level shifter. Four current limiting resistors of 10kΩ can do the job. When an LCD control line is high, the current through the 10kΩ resistor is just 40uA, so this is harmless. Note that we can’t read back from the LCD with this circuit.

Because VDD max = 7V, the PCD8544 controller can handle 5V, but the Nokia 5110 LCD works best at 3.3V. The four resistors of 10kΩ avoid streaks on the LCD display. (at 5V the screen becomes somewhat black when tested)

To have full control, you just need 5 pins. And as a classic display module among open source communities, Robu.in is giving you the handful related tutorials available over the Internet. So there is no need to panic even if you just got your foot in the door.

Can use the conductive glue to connect the module to the printed board, without cables. The metal hooks on the module can fix the module on the printed board, which is very easy to install and replace.

Can use the conductive glue to connect the module with the printed board,without connecting cable.The metal hooks on the module can fix the module on the printed board,which is very easy to install and replace.

You might notice that there are two header files included in the sketch. Adafruit_PCD8544.h is a device specific library, which contains code to run only philips PCD8544 LCD driver based displays, that is nokia 5110 and 3310. Other such libraries exist for other LCD modules. The most important method in these header files is the drawPixel(int x, int y, int color) method, which tells the LCD where to draw a pixel and of what color.

The name of this product itself is enough to explain its origin. Yes of course !!! this LCD module was used in old Nokia 5110/3310 cell phones. Now its been widely used by hobbyists for graphics, text etc.

Though it’s an industrial module, this LCD display is extremely easy to use. The Nokia 5110 is a basic graphic LCD screen for lots of applications. It was originally intended for as a cell phone screen.

This Nokia 5110 LCD Display Module is mounted on an easy to solder PCB. The Nokia 5110 LCD Module uses a Philips PCD8544 LCD driver, which is designed for mobile phones.

Nokia 5110 LCD Display Module is a low-cost monochrome LCD module comprised of 84 X 48 pixels that can be used to display rich graphics and text content. This module is a revision that accepts 3-5V input. So no extra level shifter is needed.

It uses the PCD8544 controller, which is the same used in the Nokia 3310 LCD. The PCD8544 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 48 rows and 84 columns. All necessary functions for the display are provided in a single chip, including on-chip generation of LCD supply and bias voltages, resulting in a minimum of external components and low power consumption. The PCD8544 interfaces to microcontrollers through a serial bus interface.

Can use the conductive glue to connect the module to the printed board, without cables. The metal hooks on the module can fix the module on the printed board, which is very easy to install and replace.

Easy useage Nokia 5110 screen which you can use with Arduino and different microcontrollers is a great graphic LCD for your projects. Its control pins are drawn out by placing it on a PCB. Therefore it can be used in breadboards or different circuits easily.

This LCD module uses Philps" PCD8544 driver (Nokia 3310 driver). It is a common driver in 84x48 pixel graphic screens. Therefore there are many example application and library.

These displays were used in old Nokia 5110 cell phones. It"s an 84x48 pixel monochrome LCD display. These displays are small, only about 1.5" diagonal, but very readable and come with a white backlight. This display is made of 84x48 individual pixels, so you can use it for graphics, text, or bitmaps. These displays are inexpensive, easy to use, require only a few digital I/O pins, and are fairly low power as well.

The listing says that these are new (at the bottom of this listing), these screens are actually recycled/pulled screens from actual Nokia Phones and devices in China. Because of this, there may be small blemishes or imperfections or even nicks. This is unavoidable at this point. This screen has not been manufactured for many years now. We have to take what we can get. Its still a great screen and Vetco Guarantees functionality.

This is LCD Graphics Display is straight forward to hook up and quick to get running with your Arduino or other microcontroller. At only 1.72" x 1.72", this display is easy to integrate into just about any project. The bright blue LED backlight illuminates the display from either edge.

This module requires both 3.3VDC Power and uses 3.3V Logic - To inteface this module with the 5 Volt Logic of an Arduino, we suggest our NTE4050B Non-Inverting Buffer Chip.

QTY: 1 x Nokia 5110 LCD Display for Arduino - Includes solder-on 8-Pin Single-Row header. (Header MAY be pre-soldered depending on which supplier we get these from)