raspberry pi tft display 3.5 factory

Looking for a small screen that is the same size as your Raspberry Pi? This 3.5" resistive touch screen with 480 x 320 resolution will certainly meet your needs. If further combined with a wireless keyboard, It will act as a fully functional computer that fits right in your pocket. Use it to run the Pi"s terminal, to play games, or to browse the web.

This item is more than just a screen, it is also a development friendly platform. It is seamlessly compatible with DFRobot Gravity series modules making it easy to connect or even to debug your Pi via the serial port! All the pins of Pi are left unoccupied, giving you more room to connect jumper wires.

This Touchscreen is well designed for the Raspberry Pi 3, 2 or Model B (with 40 GPIO Pins). Please note that it is not directly compatible with the old 26 pin GPIO Raspberry Pi.

Note: When using the LCD display driver be sure to power off the system using software rather than switching the power off abruptly to avoid damage to the LCD.

The 3.5 inch RPI lcd display TFT Capacitive Touch Screen is a display module can be applied to Raspberry pi 3 B+ Pi Zero etc. It can be used as raspberry pi x window display terminals.

The RPI LCD Display TFT Capacity Touch Screen Modules used 28 pins out of raspberry pi 40 pin. When installing the module attention to align the first leg of the raspberry pi and LCD module.

Is this not the cutest, little display for the Raspberry Pi? It features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay so it is slightly larger than the Raspberry Pi board, which is perfect to cover it. The plate uses a high-speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video, etc. Best of all it plugs right on top nicely covering the Raspberry Pi board. Single power from Raspberry Pi is sufficient to operate the screen. As it uses the SPI and Power pin from Raspberry Pi"s GPIO, it is nicely stacked on the RPi board. We also carry the perfect case/enclosure for Raspberry Pi 3B/3B+ and also 4B to be used with this LCD.

This 3.5" TFT display has 480x320 pixels with a 16-bit resolution and resistive touch option. It can fit directly on top of the Raspberry Pi board and gets powered from the Vcc pin, the display communicates through SPI protocol with the Pi.

Additionally, you can also use the HDMI port on pi to connect it to another display as well. It is designed for Raspberry Pi zero/Pi 2 /Pi 3 Model B / B+ and can also be used on other hardware platforms which have SPI interface. The highlight of this display module, it supports plug and play without reboot the Pi, and SPI speed runs as fast as 32MHz to support games and videos.

Our 3.5 Inch HD Display for Raspberry Pi LCD Touch Screen have complete testing equipment and fine manufacturing. We will continue to carry forward the enterprising spirit of courage to innovate, unity and hard work, dedicated to ensuring the development of the company, and providing customers with more complete services. We abide by the core values of "honesty, pragmatism, unity and innovation".

So ill start, last week i bought onw of these little screens http://www.labelectronica.com/pantalla- ... 0434466xJM but the thing is that i still cant make it work, i want the screen to work it out with EmulationStation, even better if i could put a RetroPie image there, but the thing is that i cant even make it work on Raspbian, i already have the NOOBS 1.6 installed, on that image already did the apt-get update and upgrade, i have tried these links:

And i cant make the screen to work, i dont want the touch to work because EmulationStation or RetroPie are not compatible with that, but i really want to make my screen work on the raspberry so i can go on with my project.

I have read that i need to have to find a suitable DT overlay for my display, The overlays are stored in /boot/overlays but i dont know wich i can take for my screen. And then i need to search for fb1 change on one config, and im totally lost there. Is there any Raspbian OS Image out there that i can download for that screen?

Unfortunately I can"t fully identify it from that picture. It looks similar to other screens I have seen, but I can"t be sure if it"s similar enough to try to use their drivers.

Thank you so much for your response and time helping me, i appreaciatte it so much, ill try out today, ill tell you how it goes. And again, thank you for your time.

I already did everything, when the pi starts, i can see a bit of the start code on the screen, then in turn blacks and the only thing i see is this. I remember someone told on the forum to run from ssh this code

Not without building your own kernel, unless the TFT is supported by one of the drivers defined in /boot/overlays. Take a look at /boot/overlays/README.

DougieLawson wrote:Not without building your own kernel, unless the TFT is supported by one of the drivers defined in /boot/overlays. Take a look at /boot/overlays/README.

Ok, so far the screen now works, but not works as is intended to be, it has all the colors messed up, but at least im able to see. Im trying to find out how can i fix that, i tried to put the configs on the image they sent me on the retropie image, but it didnt work, the only overlay i was able to put and get image on the screen was the waveshare35a, im using these settings:

i attach an image how the screen is working, any advice? Im using the rpi-fbcp tool, i kind of followed the instructions listed here https://learn.adafruit.com/running-open ... itft-setup but i replaced the part when they put the adafruit pitft helper as im using a waveshare clone.

Another factor is the SPI bus frequency. I don"t know what the setting is in the official Waveshare image, but https://github.com/swkim01/waveshare-dt ... verlay.dts states a max of 16000000

Step 1: Connect your Raspberry Pi to a PC LCD to Pi. Step 2: Turn on the pi and make sure its connected to the Internet via WiFi or LAN. Step 3: Open terminal in Raspbian desktop, and type the followingmands. sudo rm -rf LCD-show git clone https:///goodtft/t chmod -R 755 LCD-show cd LCD-show/ sudo ./LCD35-show Step 4: Congratulation !!touch display description Supports FBCP software driver as well, allows to config software resolution and set up dual-display Size perfectly fits the Pi (Raspberry Pi B+/2B/3B/3B+) High quality immersion gold surface plating Combined with the Raspberry Pi (refresh rate up to 50Hz), allows you to: Watch videos (multi formats like MP4) Play video games (RetroPie, take a bite) Take photos by touching (up to 17 camera modes) Use software keyboard (system interaction without Waveshare is a popular brand that has wide range of displays fo Touch Screen IPS TFT LCD is Designed for Raspberry Pi with HDMI. Features 480×320 hardware resolution, software configurable up to 1920×1080 Resistive touch control IPS technology, high quality and perfect displaying from very wide viewing angleRPI lcd display TFT Capacitive Touch Screen is a display module can be applied to Raspberry pi 3 B+ Pi Zero etc. It can be used as raspberry pi x window display terminals. [Features:] 1. This RPI lcd display TFT capa touch screenpatilble with Raspberry pi 3 modle B / Pi 2B / B+ / Pi Zero / etc.