3.5 tft lcd touch screen module quotation

ER-TFT035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller,superior display quality,super wide viewing angle.As a bonus, this display has a optional resistive touch panel and a optional capacitive touch panel with controller FT6236, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit, parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.5"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

ER-TFTM035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller and breakout board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in microSD card slot, optional 3.5" 4-wire resistive touch panel with controller XPT2046 and capacitive touch panel with controller FT6236, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover . It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.5"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

Display brilliant colors on the Displaytech 3.5 inch TFT LCD module! This LCD display has 320 x 240 RGB resolution and uses the NewVision NV3035C single chip digital driver. The TFT driver IC supports 16M colors allowing for a range of hues to be displayed and can also support up to 22 different types of input video formats within RGB, CCIR656, and CCIR601 video formats. The 3.5” TFT is available with a touch screen panel in either resistive (single-finger or stylus pressure) or capacitive (five-finger, multi-gesture) touchscreen technology.

When a tft display is considered, it is better to choose the right type of Tft display. Both Tft lcd and Tft display will provide the user with a built-in subwoofer and interfaces for multiple-facing options. On the other end of the spectrum, Tft lcd provide the required level of performance and is not the option.

Similarly, Tft lcdds offer, your customers have different options to choose from. 5-inch tft lcdds wholesale, for example, are a great choice for buyers who are looking for a 14-inch Tft LED display and a Tft display of the very basic type. Tft lcdds offer, customers have different options and choose.

This 3.5" module is a 320x240 resolution IPS TFT LCD display that includes a configurable LED driver with PWM, and an on-board FTDI FT812 Embedded Video Engine (EVE2). The LCD screen includes IPS technology which delivers enhanced color reproduction, better image consistency, sunlight readable capabilities with high brightness backlight, and boasts superior optical characteristics at any angle. This Liquid Crystal Display supports Display + Touch + Audio and has four 3.5mm mounting holes. The 24-bit true color display also includes EMI shielding on the cable, a 4-wire resistive touchscreen, and is RoHS compliant.

Newhaven Display’s 3.5” EVE2 TFT is powered by an FTDI/Bridgetek graphic engine to bring you built-in graphics operations, embedded widgets, 1MB graphics memory and more. This Human Machine Interface (HMI) display comes fully equipped with resistive touch integration. We designed the EVE2 TFTs to work with Serial SPI communication allowing for the use of low-cost MCUs as the system host, making this display both powerful and affordable.

The EVE2 TFT module is built with a feature-rich controller that offers an all in one solution for managing graphics, audio and touch. Portrait and landscape modes are supported, as well as multiple image formats and video playback. The built-in widgets include everything from buttons and sliders to gauges and clocks, making for a complete interactive interface right out of the box. No extra casing is required to mount this TFT either – just use the built-in mounting brackets with any standard M3 screws. Connect this module with the NHD-FT81X-SHIELD Arduino Shield (sold separately) for quick and easy setup with Arduino development boards. The EVE2 TFT module is the leading-edge solution for HMI displays in any application.

Enhance your user experience with capacitive or resistive touch screen technology. We’ll adjust the glass thickness or shape of the touch panel so it’s a perfect fit for your design.

TouchGFX is a unique software framework that unlocks the graphical user interface (GUI) performance of your low-resource hardware. The revolutionizing technology breaks existing restraints, as it lets you create sophisticated GUIs that fully live up to today’s smartphone standards at a fraction of the cost.

emWin is designed to provide an efficient, processor- and LCD controller-independent graphical user interface (GUI) for any application that operates with a graphical LCD. It is compatible with single-task and multitask environments, with a proprietary operating system or with any commercial RTOS. emWin is shipped as “C” source code. It may be adapted to any size physical and virtual display with any LCD controller and CPU.

1. Hello, we are looking for a TFT LCD, 3.5", 1000 nits or more, parallel interface, best view from top (hour 12). If you have it, please send me the datasheet and the quotation for 2 samples and for 200 pcs per order. Best regstrds

Kingtech IPS/ free/all/ wide viewing angle 3.5 inch 320x480 TFT LCD display is our leading TFT LCD module product. Kingtech is the only distributor of the IPS LCD panel, so we have the TFT LCD module price and resource advantage. The 3.5 inch TFT LCD display has a resistive touch and capacitive touch. The PINOUT is 40PINs, most customers like to use it.

Kingtech Diaplay, as one of LCD display panel manufacturers, has achieved great progresses in the field of LCD production. We promoise that we will provide the customers with qualified standard 3.5 TFT LCD module displays and satisfying one-stop services. Any requests will be welcomed.

The Capacitive touch panel is activated with anything containing an inductive load such as a finger or stylus. It allows for multi-touch options. When using the capacitive touch screen, the display needs a separate controller to interface with the touch panel. The display for capacitive touch is brighter since the touch panel is transparent.

The Transmissive polarizer is best used for displays that run with the backlight on all the time. This polarizer provides the brightest backlight possible. If you have a need for a bright backlight with lower power drain, transmissive is a good choice for this TFT LCD display.

Focus LCDs can provide many accessories to go with your display. If you would like to source a connector, cable, test jig or other accessory preassembled to your LCD (or just included in the package), our team will make sure you get the items you need.Get in touch with a team member today to accessorize your display!

Focus Display Solutions (aka: Focus LCDs) offers the original purchaser who has purchased a product from the FocusLCDs.com a limited warranty that the product (including accessories in the product"s package) will be free from defects in material or workmanship.

In this Arduino touch screen tutorial we will learn how to use TFT LCD Touch Screen with Arduino. You can watch the following video or read the written tutorial below.

For this tutorial I composed three examples. The first example is distance measurement using ultrasonic sensor. The output from the sensor, or the distance is printed on the screen and using the touch screen we can select the units, either centimeters or inches.

The third example is a game. Actually it’s a replica of the popular Flappy Bird game for smartphones. We can play the game using the push button or even using the touch screen itself.

As an example I am using a 3.2” TFT Touch Screen in a combination with a TFT LCD Arduino Mega Shield. We need a shield because the TFT Touch screen works at 3.3V and the Arduino Mega outputs are 5 V. For the first example I have the HC-SR04 ultrasonic sensor, then for the second example an RGB LED with three resistors and a push button for the game example. Also I had to make a custom made pin header like this, by soldering pin headers and bend on of them so I could insert them in between the Arduino Board and the TFT Shield.

Here’s the circuit schematic. We will use the GND pin, the digital pins from 8 to 13, as well as the pin number 14. As the 5V pins are already used by the TFT Screen I will use the pin number 13 as VCC, by setting it right away high in the setup section of code.

I will use the UTFT and URTouch libraries made by Henning Karlsen. Here I would like to say thanks to him for the incredible work he has done. The libraries enable really easy use of the TFT Screens, and they work with many different TFT screens sizes, shields and controllers. You can download these libraries from his website, RinkyDinkElectronics.com and also find a lot of demo examples and detailed documentation of how to use them.

After we include the libraries we need to create UTFT and URTouch objects. The parameters of these objects depends on the model of the TFT Screen and Shield and these details can be also found in the documentation of the libraries.

Next we need to define the fonts that are coming with the libraries and also define some variables needed for the program. In the setup section we need to initiate the screen and the touch, define the pin modes for the connected sensor, the led and the button, and initially call the drawHomeSreen() custom function, which will draw the home screen of the program.

So now I will explain how we can make the home screen of the program. With the setBackColor() function we need to set the background color of the text, black one in our case. Then we need to set the color to white, set the big font and using the print() function, we will print the string “Arduino TFT Tutorial” at the center of the screen and 10 pixels  down the Y – Axis of the screen. Next we will set the color to red and draw the red line below the text. After that we need to set the color back to white, and print the two other strings, “by HowToMechatronics.com” using the small font and “Select Example” using the big font.

Now we need to make the buttons functional so that when we press them they would send us to the appropriate example. In the setup section we set the character ‘0’ to the currentPage variable, which will indicate that we are at the home screen. So if that’s true, and if we press on the screen this if statement would become true and using these lines here we will get the X and Y coordinates where the screen has been pressed. If that’s the area that covers the first button we will call the drawDistanceSensor() custom function which will activate the distance sensor example. Also we will set the character ‘1’ to the variable currentPage which will indicate that we are at the first example. The drawFrame() custom function is used for highlighting the button when it’s pressed. The same procedure goes for the two other buttons.

So the drawDistanceSensor() custom function needs to be called only once when the button is pressed in order to draw all the graphics of this example in similar way as we described for the home screen. However, the getDistance() custom function needs to be called repeatedly in order to print the latest results of the distance measured by the sensor.

Ok next is the RGB LED Control example. If we press the second button, the drawLedControl() custom function will be called only once for drawing the graphic of that example and the setLedColor() custom function will be repeatedly called. In this function we use the touch screen to set the values of the 3 sliders from 0 to 255. With the if statements we confine the area of each slider and get the X value of the slider. So the values of the X coordinate of each slider are from 38 to 310 pixels and we need to map these values into values from 0 to 255 which will be used as a PWM signal for lighting up the LED. If you need more details how the RGB LED works you can check my particular tutorialfor that. The rest of the code in this custom function is for drawing the sliders. Back in the loop section we only have the back button which also turns off the LED when pressed.

STONE provides customers with an Intelligent HMI solution. The intelligent TFT LCD module with a Cortex-M4 32-bit CPU can be controlled by any MCU via simple Hex Instruction through the UART port. STONE TFT LCD module consists of a CPU, TFT drives, flash memory, UART port, power supply, etc. STONE also provides a basic control program and powerful design software (STONE TOOL Box). https://www.stoneitech.com/product/by-size/7-tft-lcd-display