10.1 inch 1200x1920 hdmi ips lcd display in stock

Take your experiments and projects to the next level with the Seeed HDMI IPS LCD display. Measuring 10.1 inches from corner to corner, it has a 1,200-by-1,920p resolution and connects via the HDMI interface. A backlight function button allows you to adjust the brightness to suit your environment. The display can also be powered using the built-in micro-USB port. In addition to working with Raspberry Pi, the screen can be used with Windows-based devices.

Here we offer you this high-resolution, ultra-wide viewing angle ISP HDMI display. Specifically, this display has a resolution of 1200*1920 and a viewing angle up to double 178 degrees. It is small and light, easy to carry, and compatible with most platforms with HDMI interface. No need for drivers, true plug and play.

This 10.1 inch high-resolution 1200*1920 IPS display is especially designed as a monitor for LattePanda V1 a windows 10 development board (not compatible with LattePanda Alpha & Delta). It gives users the ability to create all-in-one, integrated projects such as tablets, infotainment systems and embedded projects，even adding a face for your robot, you can expand your imagination, make more fun.

Up to 224 PPI, this 1200x1920 display will creating an impression of sharp print-like text. And only one connection to the LattePanda is required, it connects via an FPC cable which handles power and signal conversion. So, there is no need for the adapter board and it releases HDMI port to build dual-screen.

10.1inch Capacitive Touch Screen LCD (B), with Case and Toughened Glass Cover, 1280×800, HDMI, IPS Screen, Supports Raspberry Pi and PC, Low Power Consumption

This model is a color active matrix TFT LCD that uses Low-temperature poly-silicon TFT as a switching device. It is composed of a TFT LCD cell, IC and FPC. And it has a 7.0 inch diagonally measured active display area with WUXGA (800 horizontal by 480 vertical pixels) resolution.ItemSpecificationRemark

This 10.1 inch high-resolution 1280x800 IPS display is especially designed as a monitor for Lattepanda(which could be used as windows 10 development board), Raspberry Pi and other mini PC. The HDMI/VGA/AV interfaces ensure its wide compatibility. Making a digital photo frame, playing a video, adding a face for your robot, you can expand your imagination, make more fun.

The mentioned product is a IPS (In-Plane Switching) display with a screen resolution of 1280×800 pixels [1].It has a contrast ratio of 800:1 and a brightness of 350 cd/m^2 [1].

In terms of dimensions, the whole display has 230×149 mm, with an actual screen area of 217×135 mm [1], which means most of the display area is occupied by the actual screen.

In terms of input signal interfaces, the device supports AV, VGA and HDMI (version 1.2) [1], which means we can directly connect the Raspberry Pi to it without the need to any additional converter.

Note however that the LCD needs to be connected to a controller board, which is already included in the whole product package. We will check more on the controller board below.

If you already have some transformer that can output a voltage in this range, you can use it as long as you confirm that its polarity is the same as the one the LCD uses. Additionally, you need to make sure that it can support enough current draw to power the LCD, which can only be determined by testing since the documentation of the device doesn’t state its current draw. Taking into account these factors, my recommendation is to use the power supply wall adapter recommended by the seller, to avoid damaging the LCD.

The display was tested on a Raspberry Pi 3 model B+. Nonetheless, since it has standard video input interfaces, it should be usable with other versions of the Raspberry Pi and even with other boards. One such example are the powerful LattePanda boards, which are also mentioned as supported on the product page of the display.

Additionally, the controller board is connected to another small PCB which contains some keys that are used to control the LCD (the left connection). This PCB is shown below at figure 3.

The power supply is also connected to the LCD controller board, which is responsible to supply the display. We also connect the Raspberry (or the other device used) to this board using one of the 3 available interfaces (HDMI, AV or VGA).

It’s important to mention that the display and the keys PCB board already have cables with interfaces ready to connect to the controller board, which means that no soldering is required and the connections are simple.

What needs special attention are the display connections since they have less connectors than the pins of the controller board. So we need to put them in the correct positions, as indicated in figure 4.

As already mentioned, the controller board is connected to a smaller PCB which contains some keys to control the LCD. These keys basically correspond to the typical interface many monitors have, with a couple of buttons to turn it on, off or control parameters such as brightness.

So basically, for this LCD, we have a button to turn on and off the display. The LED present on that board changes between red and green, depending if the display is off or on, respectively.

Then, we have a menu button that, when clicked, opens an interface like the one shown on figure 6, which allows to adjust some parameters of the display.

Finally, we have a button that allows to change between the supported input interfaces. If, after connecting your device to the display you get a “No signal” message, then most likely you need to click that button to change the input interface to the correct one.

The analyzed display is a nice addition to be used with a Raspberry Pi. It is a compact solution that can even be used with other mini computers similar to the Raspberry Pi. Even though it requires some additional connections other than the HDMI one, it should be easy enough to get started.

This 10.1 inch high-resolution 1200*1920 IPS display is especially designed as a monitor for LattePanda (which could be used as windows 10 development board)

Seeed studio 10.1" display with a resolution of 1200 x 1920 pixels with wide viewing angle IPS matrix. Works with Raspberry Pi in versions 3B+ 3B+ 2B, 1B+, 1B, 1A and Zero and Zero W via the HDMI and USB cable.

The screen is small, lightweight and easy to carry. Compatible with most platforms with HDMI. In addition, the display has an adjustable backlight, which is controlled using the buttons located at the back.

In order to run the screen, you must connect the device to a Raspberry Pi via the supplied wire: HDMI and microUSB. The screen works with the latest operating system Raspbian without the need to install drivers. However, in order for the screen to display the picture properly, you should change the resolution in the configuration file. To do this, open the file config.txt and then at the end add the following statements.

5" and 7" screens can be supplied with the usual USB interface, while a 10.1" requires the current larger than the maximum supply current USB 2.0 (500 mA).