tft lcd module connector pinout supplier

A 2.4” TFT LCD module consists of a bright backlight (4 white LEDs) and a colourful 240X320 pixels display. It also features individual RGB pixel control giving a much better resolution than the black and white displays. A resistive touch screen comes pre-installed with the module as a bonus and hence you can easily detect your finger presses anywhere on the screen.

The TFT comes with an auto-reset circuit which gets active on every breakout. However, a user can reset the module using this pin also, in case setup is not resetting clean.

The TFT comes with an auto-reset circuit which gets active on every breakout. However, a user can reset the module using this pin also, in case setup is not resetting clean.

Resistive Touch Pins – Y+, X+, Y-, and X- are the 4 resistive touch pins which require analog pins to read and determine touch pins. Their overlay is fixed at the top of the module which makes them electrically separate from the TFT. They can be used is 8-bit as well as SPI mode.

The 2.4” TFT LCD module supports many modes. However, two of them are very popular among users – “SPI mode” and “8-bit mode”. The display contains pins on both sides required for a mode and a user can switch easily between them by simply rewiring the display. It should be noted that only one mode can be used at a time.

A 2.4” TFT module has a very flexible usage. It is compatible with all your DIY projects where you want to add a bright, colourful, and touchscreen enabled display.

The modules of Winstar TFT P Series are similar to Winstar TFT Q series which are also featured with an integrated 36-pinout connector on controller board. The P Series modules are derivative products from the Winstar existing standard TFT modules which uniform the pin assignment into 36 pins on a RA8875 controller board.

Winstar P Series is a TFT module Family which is including 3.5 inch, 4.3 inch, 5.7 inch, 7.0 inch, 8.0 inch and 10.2 inch TFT modules. The modules of Winstar TFT P Series which are all have an integrated 36-pinout connector on the RA8875 controller board. The P Series is featured with 8 bit or 16 bit options and already defined pin no. 33 ~ 36 as backlight supply; therefore, the customers no need to design extra backlight circuit. If the customers require different function controller for applications, you can consider choosing Winstar TFT P Series. It supports many import functions such as Chinese character display, backlight brightness adjustment, Flash Memory and touch panel driver.

Winstar TFT Q Series is a TFT module Family which is including 3.5 inches, 4.3 inch, 5.7 inch, 7.0 inch, 8.0 inch and 10.2 inch TFT modules. The modules of Winstar TFT Q Series which are all have integrated a 36-pinout connector on the SSD1963 controller board. The Q Series modules are derivative products from the Winstar existing standard TFT modules which uniform the pin assignment into 36 pins on board. The Q Series modules combined with SSD1963 controller board plus a 36 pin-out connector on board. The Q Series is available in 8 bit or 16 bit options and pre-defined pin no. 33 ~ 36 as backlight supply; therefore, the customers no need to design extra backlight circuit.

Winstar Q series is support with Solomon SSD1963 Which has the traditional inputs and drive TFT by VESA signal. Therefore, the customers don’t need T-COM circuit on board. Besides, we have integrated all functions including TFT connection, backlight driver, and touch panel into only one connection. Winstar TFT Q Series display provides the following innovative advantages to offer outstanding image quality and easily to use a colorful TFT display.

Built in backlight driver IC, all Q series TFT displays can be drive by 5.0V (3.5” and 4.3” also support 3.3V). The customers do not have to change the backlight driver circuits while change the TFT module sizes.

The 1.8inch LCD uses the PH2.0 8PIN interface, which can be connected to the Raspberry Pi according to the above table: (Please connect according to the pin definition table. The color of the wiring in the picture is for reference only, and the actual color shall prevail.)

ST7735S is a 132*162 pixel LCD, and this product is a 128*160 pixel LCD, so some processing has been done on the display: the display starts from the second pixel in the horizontal direction, and the first pixel in the vertical direction. Start to display, so as to ensure that the position corresponding to the RAM in the LCD is consistent with the actual position when displayed.

The LCD supports 12-bit, 16-bit and 18-bit input color formats per pixel, namely RGB444, RGB565, RGB666 three color formats, this routine uses RGB565 color format, which is also a commonly used RGB format

2. The module_init() function is automatically called in the INIT () initializer on the LCD, but the module_exit() function needs to be called by itself

Python has an image library PIL official library link, it do not need to write code from the logical layer like C, can directly call to the image library for image processing. The following will take 1.54inch LCD as an example, we provide a brief description for the demo.

The demo is developed based on the HAL library. Download the demo, find the STM32 program file directory, and open the LCD_demo.uvprojx in the STM32\STM32F103RBT6\MDK-ARM directory to check the program.

image.cpp(.h): is the image data, which can convert any BMP image into a 16-bit true color image array through Img2Lcd (downloadable in the development data).

This display module features high resolution, low power consumption, wide angle and easy wiring. It employs IPS display with a small size of 1.54 inches, offering 240×240 resolution. The module adopts SPI and GDI interface(work with maincontrollers with GDI port). This LCD display can be powered by 3.3V~5V, and the maximum is power consumption is 24Ma. This product can be used in many display applications: waveform monitor display, electronic gift box, electronic weather decorations, etc.

The product is a Breakout module. It adopts SPI communication and has onboard GDI interface, which reduces the complexity of wiring and can easily display the contents read from SD card.