broken lcd screen saver made in china

Established in 1995,Right Group Co, Ltd(Flagship Brand Name Monifilm) is a Taiwan Based leading screen protector manufacturer and developer of  screen protection products and optical film solution for consumer electronic and industrial applications.

Our products and solutions range from high end tempered-glass for smart phones, tablets, laptops and gadgets, to hybrid compound material and specialise optical film screen protection  like Anti-Reflective, Anti-Bacteria, Anti-Bluelight and Microlouver Technology Privacy Screen …etc; with a network of clients and business associates that streched across USA, ME, EU, Japan and Asia.

While buying a new smartphone, we make sure to accessorise our phone well. We doll it up and take care of it like a baby. But one of the most important things is its screen protectors. Choosing between screen protector vs tempered glass is essential while ensuring your phone screens’ well-being. They will help you shield your phone screens from everyday scratches, breakage or any other damage.

All it does is add an extra layer of protection over your regular phone screen. Especially if you are accident-prone or clumsy, you need to cover up your phone screens right away using the screen guards. Investing in a good screen protector vs tempered glass is probably the best way to reduce the chances of getting damaged screens, thus letting your phone have a longer lifetime. However, replacement or repairing a damaged screen could cost you a fortune. One can not afford to risk it. Better safe than sorry, no?

Choosing the right screen protector vs tempered glass for your smartphones could be a tricky one. Having a debauched quality is deadly. It is similar to wearing gloves to escape the dirt and expecting them to protect your wrist bones against fracture. There are many varieties to choose from. We will assist you appropriately so that you make an informed decision. You might be confused about whether to go for a tempered glass protector or the plastic one. Let’s go through various aspects you need to pay attention to by cautiously weighing their cons and pros so that you make an exemplary and smart purchase.

Cracked or broken touchscreens are very commonly seen rather than intact ones. Plastic screen protectors vs tempered glass are universally found in the market. Just like a coin, they have both pros and cons. Let’s analyse them:

Plastic screen guards are very resilient in making them last longer. Experiments have shown that hammering or even dropping it from a height onto rocks has no effect on the plastic screen protector vs tempered glass.

Another pro linked with the plastic screen protectors is this that they are reusable. At any point, you can take them off, store it and use it again later. This feature ensures their long-term usage. In case you need to put on a waterproof case, you can take the plastic ones off and put the other one on.

There are many downsides which come along the plastic screen guards. Due to being made up of plastic material, over time these protectors lose their clarity. That often results in haziness and looks repulsive while one uses them.

It is relatively thinner than the glass tempered screen protectors. The thicker the screen guard, the tough it is and thus affording our screens resistance against damages.

These are not fingerprint resistant and leaves them on your screen after you use your smartphones. It doesn’t look so pleasant. You need to often wipe them off your screen after usage.

Tracking your fingers and navigating over a plasticscreen protector vs tempered glass may not feel as smooth as when you are using the tempered glass screen protector.

In one line, these are everything the plastic ones aren’t. They are the exact opposite of what we mentioned above. They are the more traditional choice for those who wish to cover their phone screens without harming the edges. Tempered glass screen protectors are made by extensively heating the glass and quickly cooling it. As the glass endures both extreme heat and then rapid cooling, they end up being incredibly stronger.

Tempered glass screen protectors contain multiple layers, including an oleophobic nano-coating, anti-shatter film and a penetrable silicone coating on top of the tempered glass. These compressed layers add to the heat and scratch resistivity of the tempered glass as much as five times stronger than normal glass.

They may be a costlier alternative than the plastic ones, but it safeguards your device better. Tempered glass screen guards are much sturdier and robust in nature than the former.

You might not even notice they are on the top of your mobile screen. It doesn’t make your phone look hideous by not compromising with the look of your smartphone. They provide you clarity as much as your smartphone would without any screen protector over its screen.

In case if your tempered glass breaks, it breaks into small, blunt chunks and that doesn’t compromise with the safety it was providing to your phone screen.

Since it is a glass, chances are you might cut yourself after a bad chip. You shouldn’t reuse a cracked tempered glass screen protector, unlike the plastic ones.

Tempered glass screen guards don’t offer as much impact protection as promised by a plastic screen guard. The hammer experiments we mentioned above are not meant to be run on these tempered glass screens.

A plastic screen protector is comparatively a lot cheaper than the tempered one. You can buy multiple plastic protectors at the price of a single tempered screen protector. This is chiefly due to the quality of the plastic or glass.

The plastic screen guards are not as sleek and modish as the tempered glass screen protectors. Instead, the tempered glass gives you a pleasant look at your smartphone.

Installing the plastic screen guards on your phone screens is quite more tedious than the tempered glass ones. There are various kinds of glass protectors for tempered glass screen protectors, such as full or bezel adhesive.

You can feel the difference between both plastic and tempered glass screen protectors. Your fingers glide smoothly over the tempered glass, and it’s amusing to use. They feel more like the original screen.

Screen protectors can safeguard your smartphone up to a limit. However, no matter which one you opt for, you need to be careful with your smartphones. While this is entirely your choice which screen protector to go for, in our opinion, a tempered glass screen protector is a much more valid, resistant and solid alternative. In a nutshell, the plastic one gets dull over time, but the tempered glass one is modish.

Tempered glass screen protectors were first introduced to the market in plastic protectors. However, when it comes to the ever-changing demands of the smartphone world, a plastic screen protector can no longer adapt its qualities or features to meet those needs. There are a lot of distinctions between tempered glass and plastic screen protectors that have been covered in this post.

There may be additional elements that impact your choices for screen protector vs tempered glass, but it is evident from the information provided above that, on average, a glass screen will be the most effective option. This is because they are more convenient to use, are more pleasant to look at, and provide more protection.

Cracked or broken mobile device screens can be costly to fix, but a few inexpensive do-it-yourself strategies can eliminate a repair shop visit and salvage your tablet or phone.

Third-party repair shops typically replace glass on a tablet for about US$100-$200, depending on the model. Replacing the tablet’s touchscreen can cost $50-$75 extra.

Replacing the cracked glass with a functioning touchscreen is much cheaper. You usually can find suppliers online for $6 to $20 for a phone. A tablet replacement digitizer can cost about $50 or more if you perform the work.

It is first things first when it comes to fixing cracks on a smartphone’s screen. Often, the actual screen is not cracked at all. You may have installed a glass screen protector when you purchased the phone.

The film covers can become cloudy or scratched. They usually help absorb shock from items dropping on the tablet to lessen risk of cracking the touchscreen glass under it.

When the culprit really is a damaged screen, choosing one of the next three approaches can help you solve the problem. You might be able to repair the damage rather than replace it.

For instance, is the screen clouded or otherwise damaged from your mistaken use of harsh cleaning fluids or coarse paper towels to clean the screen? If so, there is a fix for that.

Is the screen merely cracked or full-out broken — as in massive spider cracks from being smashed? You can cure a cracked screen on a phone or tablet more easily with Sugru, a commercial product. A fully cracked screen on either type of device is a solid candidate for a screen replacement.

If your phone or tablet screen shows signs of cleaning abuse or wear from heavy handling, return its condition to nearly new with an oleophobic coating kit. This is an oil-repellent coating that protects the screen, along with adding smoothness and reducing fingerprints.

Prepare a wiping finger. The oleophobic coating’s liquid solvent evaporates very quickly when applied, so once you start, work quickly. Wrap one finger with plastic wrap or a sandwich bag. Use this finger to rub the coating liquid onto the screen.

Apply 10-15 drops of the coating to the screen’s surface. If the phone or tablet screen has a large surface, apply 10 drops to a portion of the screen, working on one portion at a time.

Wipe the screen dry with a clean microfiber cloth. Then give the coating time to dry. Do not touch the screen for 8-12 hours to allow the coating to bond to the surface.

If your only complaint involves tiny scratches and cracks on a smartphone screen or a tablet glass, there are remedies that work with varying degrees of reliability. You can use a household eraser pad or an actual pencil eraser.

Sugru is a moldable glue kit for repairing rather than replacing cracked screens. Actually, the product was not created with phone and tablet repairs in mind. Its intended purpose is more in the line of general repairs where bonding surfaces together and filling surfaces are needed.

Depending on how badly the screen is damaged, it can be a good solution for cracks that spread from the phone or tablet screen’s edges. However, for massive cracks that spread over the entire screen — as spider cracks tend to do over time — it will be a short-term fix at best.

If your phone or tablet screen has suffered more serious damage, full scale surgery is the only option other than getting a new device. Repairing the device’s LCD screen is a complicated procedure due to the compact internal design.

The repair process involves completely dismantling the phone or tablet’s outer casing. It is particularly easy if the replacement screen comes with a top frame.

Otherwise, you may have to seal the layers to avoid loss of structural strength and moisture/dust protection. You can use either sealing pads for the size of the particular device at hand or double-sided sticky tape. A simpler solution for phone screen replacement is to use B-7000/T-7000 glue.

The first step is to tear down the device so you can assess the extent of the damage and determine what screen parts to order. Locate the model number for the LCD screen. Use this number in an Internet search to find a replacement screen.

The part or model number usually is printed on a label adhered to the sensor cable attached to the screen. You can access this cable after you separate the screen from the rest of the unit. Carefully disconnect the cable connector from the backside of the screen along the edge.

Step 3: Unscrew the Phillips or Torx screws that hold the motherboard-containing back frame to the LCD-containing chassis and place the screws in a bowl for safe-keeping. Then separate the back frame from the chassis by gently and carefully pulling the two apart.

Step 5: Remove the LCD-containing chassis from the front frame or bezel and glass assembly by unscrewing a second batch of screws. Store the second set of screws in a second bowl. Remove any further parts such as the camera.

Step 6: Don’t touch the LCD face. Separate the existing, damaged glass from the bezel or front frame by waving the heat gun over the adhesive join and pulling apart. Wear gloves here because the process involves further breaking the glass.

Step 3: Thread the digitizer cable and remount the new digitizer glass to the bezel by firmly pressing it into place. Then remove any dust from the LCD and glass with canned air.

Replacing damaged touchscreens and digitizer panels is not rocket science, but the process does require careful attention to details. Following visual guides and screenshots can make the difference between initial success and having to make second or third efforts.

OK, I have been reading these comments and while there are some that are correct, there are few or more that are way out there. Guys, as a electronics tech, I have fixed many phones such as this in my time. Yes the cheap screens will fix it most of the time, but there are times when this is not the case. There is no easy fix for this.

1) Check if the screen responds to any touch at all. If it does work but you get “ghost touch”, problem is likely going to be fixed without replacing the screen. Usually one of the connectors are dirty or not plugged in correctly. Easier fix is to open the iphone, lift the screen from the rest of the case/motherboard and unplug the lcd and other connectors that run from the screen to the board. You could use 99% alcohol and a tooth brush. Scrub the connectors gently and wait a few seconds for the alcohol to evaporate before plugging the connectors in. Usually this will fix the trouble and you will have a perfectly working phone without replacing any parts. IMPORTANT: Do not use 50% or 75% alcohol or acetone. Low grade alcohol is 50% water (and we know what water does to the phones)and the acetone can short out the motherboard or melt the certain parts that are important.

2) If only lower or upper or left or right side of the screen work, chances are very high that you need to replace the screen. You can try the solution above, but it will rarely work.

3) If you had a cracked screen and replaced it with the new one and now touch is not working, chances are that you either did not assemble it correctly or the screen is bad. If your old screen was responding to the touch and the new one doesnt, simply try to install the old one again and see if it still responds to the touch. If it does then the new screen is defective and you should return it. If it doesnt then try the first solution again to see if this will help.

The iphone uses BGA type of chips for all of their phones. These are “ball grid array” chips and they have these tiny little ball of solder that connect to the board. Some may have 10 and some chips have 50-60 or more of them. You can not see them like you would on a SM chip(surface mount). While you are using the phone they have electricity running through them . This makes them heat up and cool down constantly. Problem that occurs is called “Cold solder”. Over the time because of it heating and cooling the solder become brittle and it cracks. Once it cracks it will start to cause problems. This is why sometimes if you press the phone in certain spot it actually starts to work. Well, you are forcing the chip to connect to the board by pressing it in, but once you let go it stops. This sometimes can be fixed by reheating the chip, or to use technical term, “re-flowing”. sometimes it needs so little that the heat may just connect the broken link and it will be fine. Temperature you use to reheat it very important. If you take it to the shop and you see them using one of those industrial heat guns used to strip the paint from home depot, you will probably need a new phone. Temperature is important, but the force of the air flow just as important.

I know most people wont read this whole thing, but there is some useful information I wrote here and everything I wrote applies to almost any phone on market today. All of the phones are basically the same. They all have the same parts, only difference if what those parts are going to look like and their location o the phone, but they all need to have the CPU’s, memory chips, power management chips, lcd or touch controller chips and so on.

OK, I have been reading these comments and while there are some that are correct, there are few or more that are way out there. Guys, as a electronics tech, I have fixed many phones such as this in my time. Yes the cheap screens will fix it most of the time, but there are times when this is not the case. There is no easy fix for this.

1) Check if the screen responds to any touch at all. If it does work but you get “ghost touch”, problem is likely going to be fixed without replacing the screen. Usually one of the connectors are dirty or not plugged in correctly. Easier fix is to open the iphone, lift the screen from the rest of the case/motherboard and unplug the lcd and other connectors that run from the screen to the board. You could use 99% alcohol and a tooth brush. Scrub the connectors gently and wait a few seconds for the alcohol to evaporate before plugging the connectors in. Usually this will fix the trouble and you will have a perfectly working phone without replacing any parts. IMPORTANT: Do not use 50% or 75% alcohol or acetone. Low grade alcohol is 50% water (and we know what water does to the phones)and the acetone can short out the motherboard or melt the certain parts that are important.

2) If only lower or upper or left or right side of the screen work, chances are very high that you need to replace the screen. You can try the solution above, but it will rarely work.

3) If you had a cracked screen and replaced it with the new one and now touch is not working, chances are that you either did not assemble it correctly or the screen is bad. If your old screen was responding to the touch and the new one doesnt, simply try to install the old one again and see if it still responds to the touch. If it does then the new screen is defective and you should return it. If it doesnt then try the first solution again to see if this will help.

The iphone uses BGA type of chips for all of their phones. These are “ball grid array” chips and they have these tiny little ball of solder that connect to the board. Some may have 10 and some chips have 50-60 or more of them. You can not see them like you would on a SM chip(surface mount). While you are using the phone they have electricity running through them . This makes them heat up and cool down constantly. Problem that occurs is called “Cold solder”. Over the time because of it heating and cooling the solder become brittle and it cracks. Once it cracks it will start to cause problems. This is why sometimes if you press the phone in certain spot it actually starts to work. Well, you are forcing the chip to connect to the board by pressing it in, but once you let go it stops. This sometimes can be fixed by reheating the chip, or to use technical term, “re-flowing”. sometimes it needs so little that the heat may just connect the broken link and it will be fine. Temperature you use to reheat it very important. If you take it to the shop and you see them using one of those industrial heat guns used to strip the paint from home depot, you will probably need a new phone. Temperature is important, but the force of the air flow just as important.

I know most people wont read this whole thing, but there is some useful information I wrote here and everything I wrote applies to almost any phone on market today. All of the phones are basically the same. They all have the same parts, only difference if what those parts are going to look like and their location o the phone, but they all need to have the CPU’s, memory chips, power management chips, lcd or touch controller chips and so on.

So, you’ve accidentally dropped your phone with its face down onto a brick floor… and on picking it, all you can see now is a new flower or cobweb artwork on your screen. You’re half frustrated and somewhat indecisive about what to do next until you remember you"ve applied a tempered glass protector earlier. Even so, you’re not sure which of the glasses got cracked? And now, you’re probably thinking of removing the tempered glass straightaway. But wait! How do you know whether you cracked the main phone screen, or it"s just the tempered glass protector? Find out below!

Moving forward, you can flash a bright light on the screen to check if your phone screen is broken or it"s just the tempered glass. Most times, flashing a bright light on the screen won"t cause much refraction of light if only the tempered glass was broken. However, you get much light refraction if the main phone screen is broken.

More so, seeing some deep lines and cracks under the tempered glass probably means the phone screen is cracked. If the damages are not so deep, however, then only the tempered glass is cracked.

Next, you should examine the edges and corners of the phone screen. If there are cracks or lines there, that means your phone screen is cracked. Most screen protectors don"t cover the entire part of the screen, so looking at the edges shouldn"t be a problem. Meanwhile, you may need to remove your phone’s back cover first.

Lastly, if you"re still not convinced whether you cracked your phone screen or the tempered glass, you should take a bold step and remove the tempered glass. Doing that will give you a clean look at what the damaged part looks like.

Note:Be gentle and calm while removing the tempered glass to avoid damaging the screen and your fingers. And if the adhesive on the tempered glass is too hard, you may need someone else’s assistance.

If you’re lucky enough, you may find out that the crack is not extended to the main screen. In that case, you can purchase a new tempered glass at a low cost in the nearest store. Otherwise, visit the official service provider to replace your phone"s broken screen as soon as possible to avoid damaging your fingers and other components of the device.

If your phone is cracked, you can take it to a phone repair technician or mobile phone repair shop near you to check whether only the tempered glass is broken or the main screen is broken.

Today, a large number of people use tempered glass protectors with various levels of protection to give their phone"s screen extra protection. Nonetheless, tempered glass screen protectors aren"t 100% safe. You may end up breaking your phone"s screen if you smash it so hard than what the protector can handle. Before you rush to remove the tempered glass protector after accidentally dropping your phone, it’s worth checking if the main screen or only the tempered glass protector was broken by trying all the tricks mentioned above.

However, if your phone screen is cracked, there"s nothing else you can do than to visit the official phone repair service provider for your brand for screen replacement service.

Carlcare Service is the official repair service provider for these brands. Our certified technicians use only original TECNO, Infinix, or itel replacement parts, assuring you get a successful screen replacement for your device.

Replacing your broken screen at Carlcare is super easy. All you need to do is check the screen replacement price for your phone, make an online reservation with us, and visit the selected centre to replace your phone screen.

More so, you get an additional warranty after replacing your phone screen at Carlcare, giving you rest of mind on the replacement service. If your phone gets faulty naturally during the warranty period, we"ll fix it with no recurring charges.

This brand new touch screen lcd, allowing you to repair damages like broken lcd screen discoloration, dead pixels, scratched touch screen, and much more!

There is nothing more heartbreaking than to see your phone’s screen getting cracked from a simple drop. I know I"ve been there plenty of times with cheap to expensive smartphones. Though getting a phone screen cracked is a quite common problem, you need to know some ways to cope with the cracked screen. Have you noticed that once the screen gets a minor crack, it starts spreading? If so, you may be wondering how to stop a crack from spreading on phone instead of replacing or taking it straight to a service store. You need to take preventive actions to stop the spreading of the cracked phone. Here are some of the best ways, that I"ve learned as well as what industry professionals recommend doing:

First, you need to assess the damage and know if your phone’s screen has shattered. There is a chance that there are some small glass particles here and there. So, be very careful and do not cut your fingers. Assess whether the screen of your phone has cracked, or fully shattered. Depending on it, there are some temporary solutions that you can try. Also, you need to determine whether the screen is actually damaged or just the protective layer on it.

Why is it important to take immediate steps when the screen is broken? Of course, the smartphones are designed in such a way that the dust, moisture and debris are kept away from entering into the machine. Once the screen cracks, that protection is compromised and your phone is vulnerable to moisture and dust.

If it is just a crack on your phone’s screen, then you can apply a temporary seal to prevent the crack from spreading or growing further. For this temporary seal, you need to apply a compound called cyanoacrylate. Tilt the phone back and forth for covering the entire crack properly. You have to apply it evenly and wipe away any excess left over. Now, let the glue dry first before using. Be advised that this is not a preferred method, and is only a temporary fix. You can also apply a screen protector to cover the crack until you get it professionally repaired.

If your phone screen is cracked to a great extent or shattered, then it is best for you to visit a professional. Take your phone to a service center or a  mobile repair professional to get the screen fixed. It is important to take a permanent step in repairing the screen in order to avoid the dust and debris from getting into the phone. Also, this will help you to stop the screen from cracking further causing more problems.

An alternative to replacing a cracked smartphone screen, using the above steps will help stop a crack from spreading on the phone. As always, DIY projects can cause more havoc if user error occurs, so consulting or having the phone serviced at a repair shop is always the best solution. Plus, it usually comes with a warranty.

Smartphones have become one of the most important things in our daily lives. Moreover, the screen size of mobile phones is getting bigger and bigger, so for such a big screen, it is easy to cause damage to the screen. Therefore, the screen protector has become the best choice for the protection. Ceramic screen protector and tempered glass screen protector are both common types of screen protectors. So what is the difference between ceramic screen protector and tempered glass screen protector.

The ceramic screen protector also called as inorganic ceramic film is one of the solid screen protector. It is made from alumina, zirconia, Titania. After high temperature treatment the ceramic screen protector is featured with high temperature resistance, corrosion resistance, high mechanical strength, strong antimicrobial ability. So it is very suitable for mobile phone screen protection, and can be used for a long time. But it is high in cost.

Tempered glass screen protector was launched in China at the year of 2012, It has quickly become popular since its release, and in fact, it is still the most widely used type of screen protector. There are two types of tempered glass screen protectors, one is full coverage, and the other has plastic or glass fiber edging on the edge.

A common glass screen protector is 5 times higher than the standard of PET film, and has a thickness of 0.3 mm, which can completely cover the original screen, prevent damage and scratches from external forces.

The biggest advantage of tempered glass screen protector is that it feels natural, high hardness and has good protection. Moreover, the glass itself has better light transmittance than plastic, the high transparency of the glass allows him to maintain the original picture quality of the cellphone.

However, poor quality tempered glass screen protector is not close to the screen at the edge, and you can notice rainbow patterns appear at certain angles, which will greatly affect the look.

The ceramic screen protector mainly prevents signal isolation and will not interfere with the signal communication. Due to material problems, the tempered glass is easier to isolate the antenna transmission.

When it comes to service life, the ceramic screen protector is a kind of soft film, with higher bending performance, and the edge will not be broken, it can be used for the whole service life of your phone. However, the glass screen protector is easily broken, so you may need to change the screen protector frequently.

The Spigen Glas.tR EZ Fit (Sensor Protection) Tempered Glass Screen Protector is the best screen protector we’ve found. It’s as clear and strong as any glass protector we’ve ever tested, and the nearly foolproof installation system is better than any other. Also, the Spigen protector covers the front-facing cameras, providing as much protection as possible (unlike some models that leave the iPhone 13’s notch exposed). Plus, you get two protectors in each inexpensive package.

It’s much more difficult to install a screen protector on the iPhone 12 or iPhone 13 than it is on previous iPhone models: The edge-to-edge display has fewer features (like a Home button) that you can use to align the protector, so an alignment tool is essential for good installation. The Spigen model is the absolute best we’ve found, and the included visual instructions make the process clear. Each box includes two plastic installation trays, with the glass already in place. Once you’ve cleaned your phone’s glass with the included alcohol wipe, dry wipe, and dust-removal sticker (if necessary), you peel off the backing from the screen protector and snap the frame onto your phone. This design ensures you can’t misalign the glass. The instructions guide you to press and slide along a sticker on the front of the protector, and then remove the frame.

I’ve installed hundreds of glass screen protectors over the past 10-plus years, and the recent innovation of this frame has completely changed how I think about screen protectors. Now anyone—not just those with experience and a steady hand—can line up a protector perfectly every time. As long as you clean the screen well before installation, there won’t be any air bubbles underneath.

The Glas.tR EZ Fit (Sensor Protection) covers the iPhone’s display yet leaves enough room that it won’t interfere with most cases. We appreciate that the glass’s edges aren’t sharp—something we’ve seen with several glass screen protectors—since that can make a phone uncomfortable to use. This protector matches the size and shape of the iPhone’s display, and on the iPhone 13 models, it leaves only the earpiece exposed. The rest of the “notch,” the black area where the Face ID system is located, is covered and protected. We tested extensively to ensure the cameras and sensors wouldn’t be impacted by being covered with glass, and we found no issues. Even a selfie taken with the sun glaring over my shoulder looked the same as one taken with an uncovered phone.

Spigen’s glass is as clear as it gets. We saw no issues with clarity or brightness, and we quickly got used to the Glas.tR EZ Fit being on the phone. Although any glass surface will accumulate fingerprints and oil from skin, we found that this one didn’t show them too readily, and they wiped off easily. The touchscreen’s responsiveness was unaffected, since it still recognized even the slightest brush of a finger (and still worked with touchscreen gloves).

In our Mohs hardness tests, the Glas.tR EZ Fit measured between 7 and 8. That’s as high a rating as we found with any other glass screen protector we’ve tested, and it’s significantly higher than with some of the competition. We also didn’t see any damage when we tested the Glas.tR EZ Fit using house keys, a good sign of real-world protection. And after carrying the phone in a pocket for a few weeks, we didn’t see any significant buildup of dust around the glass’s edges, which is a problem with some adhesive protectors.

I’ve installed hundreds of glass screen protectors over the past 10-plus years, and the recent innovation of this frame has completely changed how I think about screen protectors.

Not only is the Glas.tR EZ Fit much less expensive than the big brands, but the low-priced package also includes two screen protectors. And since it’s unlikely that you’ll mess up the installation, you’ll have a backup or an extra protector to share with a friend.

Spigen also sells versions of the Glas.tR EZ Fit for the 12.9-inch iPad, for the 11-inch iPad Pro/10.9-inch iPad Air, and for the 4th- and 5th-generation iPad mini; there’s a similar installation system but only one piece of glass per pack. This is by far the easiest screen protector we’ve ever installed on an iPad, but because of the larger screen size, you’re more likely to end up with a speck or two of dust underneath the glass.