3.5 inch 320 x 480 tft lcd display touch pricelist

ER-TFTM035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller and breakout board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 8-bit /9-bit/16-bit /18-bit parallel ,3-wire,4-wire serial spi interface.Built-in microSD card slot, optional 3.5" 4-wire resistive touch panel with controller XPT2046 and capacitive touch panel with controller FT6236, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover . It"s optional for font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested. Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.5"TFT Touch Shield with Libraries, EXxamples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

ER-TFT035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller,superior display quality,super wide viewing angle.As a bonus, this display has a optional resistive touch panel and a optional capacitive touch panel with controller FT6236, so you can detect finger presses anywhere on the screen and doesn"t require pressing down on the screen with a stylus and has nice glossy glass cover and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO ARM and Raspberry PI.It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.It supports 8080 8-bit,9-bit,16-bit, parallel,3-wire,4-wire serial spi interface. FPC with zif connector is easily to assemble or remove.Lanscape mode is also available.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 3.5"TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560 and Uno . For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.

NMLCD-35320480-CTP-CLBis a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with a Touch Panel (TP)，with a Cover Lens Bezel(CLB). The module display area contains 320 x 480 pixels. This product accords with RoHS environmental criterion.

Shenzhen SLS Industrial Co.,ltd established in 2003, is a professional LCD module manufacturer and solution provider. We have 1 full-auto COG assembly line, 2 semi-auto assembly line, backlight assembly line, no dust TP bonding line and manufacturing tech support, we can provide unique, innovative and cost effective LCD module development and manufacturing. Our product range includes: middle-small size TFT LCD, industrial capacitive touch panel... Our LCD products have been widely used in communications, GPS, Equipment, electronic audio-visual, instrumentation, household appliances, PDA and other industries.

To provide superior, commercially-ready LCM and TP solutions that fulfill our vision of exceeding customers’ expectations through design, manufacturing and worldclass customer support of our core technology.

NMLCD-35320480-RTPis a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with a Resistive Touch Panel (RTP). The module display area contains 320 x 480 pixels. This product accords with RoHS environmental criterion.

Shenzhen SLS Industrial Co.,ltd established in 2003, is a professional LCD module manufacturer and solution provider. We have 1 full-auto COG assembly line, 2 semi-auto assembly line, backlight assembly line, no dust TP bonding line and manufacturing tech support, we can provide unique, innovative and cost effective LCD module development and manufacturing. Our product range includes: middle-small size TFT LCD, industrial capacitive touch panel... Our LCD products have been widely used in communications, GPS, Equipment, electronic audio-visual, instrumentation, household appliances, PDA and other industries.

To provide superior, commercially-ready LCM and TP solutions that fulfill our vision of exceeding customers’ expectations through design, manufacturing and worldclass customer support of our core technology.

This is the price (excluding shipping and handling fees) a seller has provided at which the same item, or one that is nearly identical to it, is being offered for sale or has been offered for sale in the recent past. The price may be the seller"s own price elsewhere or another seller"s price. The "off" amount and percentage simply signifies the calculated difference between the seller-provided price for the item elsewhere and the seller"s price on eBay. If you have any questions related to the pricing and/or discount offered in a particular listing, please contact the seller for that listing.

By continuing to use AliExpress you accept our use of cookies (view more on our Privacy Policy). You can adjust your Cookie Preferences at the bottom of this page.

By continuing to use AliExpress you accept our use of cookies (view more on our Privacy Policy). You can adjust your Cookie Preferences at the bottom of this page.

This small 3.5-inch touch screen module is designed especially for Raspberry Pi, using the latest Linux Core system. This is ideal for DIY anywhere, anytime and does not require any separate power source or case to hold it. The module sits right on top of Pi. The screen also comes with a stylus to interact with the small screen.

Global Alliance specialized with products quality produced of Uno, Mega, Nano series, very electronic experienced very process and workmanship more than 100 workers, a collection of scientific research, desigin, production, maintenance

1st generation: with flat display area and flat touch area, the border can be curved. Orient Display uses glass touch sensor and IML (In-Mold Lamination) technology to produce the products.

2nd generation: with flat display area and flat touch area, the border area can be flat or cuver in the middle. Orient Display still uses glass touch sensor and cold bending lens to produce this kind of products.

3rd generation: with flat display area and curve touch area, the border area can be flat or cuver in the middle. Orient Display uses glass or film touch sensor and hot bending lens to produce this kind of products.

4th generation: with curve display area and curve touch area, the border area can be flat. Orient Display uses flexible touch sensor to produce this kind of products.

Orient can provide the traditional GG (Glass Glass) touch screen, OGS (One Glass Solution) touch screen, PG (Plastic Glass) touch screen. GF (Glass Film) touch screen, GFF (Glass Film Film) touch screen.

Based on the above five types of touch panel technology, Orient Display can also add different kinds of features like different material glove or stylus or pencil touch, water environment touch, salt water environment touch, hover touch, force (3 dimensional) touch, haptic touch etc. Orient Display can also provide from very low-cost fixed area button touch, single (one) finger touch, double finger (finger+ gesture) touch, 5 finger touch, 10 points touch or even 16 points touch.

Considering the different shapes of the touch surface requirements, Orient Display can produce different shapes of 2D touch panel (rectangle, round, octagon etc.), or 2.5D touch screen (round edge and flat surface to create edge-less impression) or 3D (totally curved surface) touch panel.

Considering different strength requirements, Orient Display can provide low-cost chemical tampered soda-lime glass, Asahi (AGC) Dragontrail glass and Corning highest generation Gorilla glass. With different thickness requirement, Orient Display can provide the thinnest 0.5mm OGS touch panel, to thickness more than 10mm tempered glass to prevent vandalizing, or different kinds of plastic touch panel to provide glass piece free (fear) or flexible substrates need.

Orient Display can also provide full customized or part customized solutions for our customers to enhance the viewing experience. Orient Display can provide all the different kinds of surface treatments, such as AR (Anti-reflection); AG (Anti-glare), AF (Anti-finger print or Anti-smudge); AS (Anti-smashing); AM (Anti-microbial), IMITO (Index Matching Indium Tin Oxide), Anti Sparkling etc.

Orient Display can also provide both dry bonding (OCA, Optical Clear Adhesive), or wet bonding (OCR, Optical Clear Resin and OCG, Optical Clear Glue) to get rid of light reflective in air bonding products to produce high end touch screen monitor much more readable under sunlight and much more robust as well.

Touch panels have been a much better human machine interface which become widely popular. Orient Display has been investing heavy for capacitive touch screen sensor manufacturing capacity and LCD module production ability. With Orient huge production capacity, top notch quality, and competitive pricing, Orient has been working with top LCD panel manufacturers ,AUO, BOE, LG, Innolux and top touch controller manufacturers , Atmel (Microchip, Cypress, Synaptics, Elan, NXP, Goodix, Sharp, Hydis etc. to provide the best touch display technology in the market, such as IPS, MVA, in-cell, on-cell, automotive grade etc.

It is a new technology replace ink printing cover plate with visual area and black border area are integrated with seamless black design using AG/AR surface treatment. Non ink printing AR/AR seamless black optical cover plate can be customized to match touch display module to achieve the best integrated seamless black solution.

With high transmittance rate of over 90% low optical delay, no interference and Moore fringe phenomenon, low square resistance ITO of lower than 20 ohms , white and clear with yellow index Yi around 1, bending resistance which can last 200,000 times with bending radius R6.5.

With high transmittance rate of over 90% low optical delay, no interference and Moore fringe phenomenon, low square resistance ITO of lower than 20 ohms, white and clear with yellow index Yi around 1, bending resistance which can last 200,000 times with bending radius R6.5.

Orient Display developed a special smoke film which is very low cost but gives the customer a optical bonding performance. Smoke film uses optical interference to reduce the glass-air interface reflection for air (perimeter) bonding between LCD and touch screen.

3.5inch RPi LCD (A) and 3.5inch RPi LCD (B) are hardware compatible with each other (uses different driver), and can be mutually substituted in most cases. (A) for low cost ver. while (B) for IPS ver. with better displaying.

Why the LCD doesn"t work with my Raspbian?To use the LCD with the Raspberry Pi official image, driver (SPI touch interface only) should be installed first. Please refer to the user manual.

However, for the first testing, you may want to use our image directly (if provided).Why the LCD still doesn"t work with the Waveshare provided image?Make sure the hardware connection is correct and connects fine.

Since the first-generation Raspberry Pi released, Waveshare has been working on designing, developing, and producing various fantastic touch LCDs for the Pi. Unfortunately, there are quite a few pirated/knock-off products in the market. They"re usually some poor copies of our early hardware revisions, and comes with none support service.

This color touchscreen LCD TFT display is 3.5" diagonal, bright 6 white-LED backlight and colorful! 480x320 pixels with individual RGB pixel control.

This display has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. The display can be used in two modes: 8-bit or SPI. For 8-bit mode, you"ll need 8 digital data lines and 4 or 5 digital control lines to read and write to the display (12 lines total). SPI mode requires only 5 pins total (SPI data in, data out, clock, select, and d/c) but is slower than 8-bit mode. In addition, 4 pins are required for the touch screen (2 digital, 2 analog).

8 bit digital interface, plus 4 or 5 control lines (12 pins minimum) or SPI mode with 4 or 5 SPI data/control lines (4 pins minimum) - not including the touch screen.