adafruit 2.8 tft lcd with touch screen quotation

With four bright white LED backlight and 240 x 320 pixels with individual RGB pixel control, this colour 2.8in. TFT display features a resistive touchscreen for fingertip detection across the entire screen surface. The workload is lifted from the microcontroller by a built-in controller equipped with RAM buffering, and the display board has two modes: 8-bit and SPI.

Add some jazz & pizazz to your project with a color touchscreen LCD. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful! 240x320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128x64 display. As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

This display has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. The display can be used in two modes: 8-bit and SPI. For 8-bit mode, you"ll need 8 digital data lines and 4 or 5 digital control lines to read and write to the display (12 lines total). SPI mode requires only 5 pins total (SPI data in, data out, clock, select, and d/c) but is slower than 8-bit mode. In addition, 4 pins are required for the touch screen (2 digital, 2 analog)

Adafruit wrapped up this display into an easy-to-use breakout board, with SPI connections on one end and 8-bit on the other. Both are 3-5V compliant with high-speed level shifters so you can use with any microcontroller. If you"re going with SPI mode, you can also take advantage of the onboard MicroSD card socket to display images. (microSD card not included, but any will work)

8 bit digital interface, plus 4 or 5 control lines (12 pins minimum) or SPI mode with 4 or 5 SPI data/control lines (4 pins minimum) - not including the touch screen.

X2 Robotics is a supplier of electronic parts and components in Canada. We carry a large selection of open source electronics such as Adafruit, Arduino, Pololu, Raspberry Pi, SparkFun and more. We ship orders to anywhere in Canada or the United States. We also have a showroom located on North York, ON where you can pick up online orders as well as browse and purchase products in person.

Spice up your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, these displays has a resistive or capacitive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

We"ve updated our original v1 shield to an SPI display - its a tiny bit slower but uses a lot less pins and is now much easier to use with Mega & Leonardo. We also include an SPI touchscreen controller so you only need one additional pin to add a high quality touchscreen controller. Even with all the extras, the price is lower thanks to our parts sourcing & engineering skillz!

Adafruit invests time and resources providing this open source design, please support Adafruit and open-source hardware by purchasing products from Adafruit!

The Adafruit 2.8in. TFT LCD Touchscreen Display brings QVGA graphics to your next project using only 5 x SPI pins or 12 x GPIO pins if you can spare them. The screen is bright with a 4-LED backlight and can display 18-bits of colour (262,000 colours). There"s a display controller built in so your microcontroller doesn"t need to get involved in refreshing the screen, it just has to write the pixels once then it can move on to other tasks. SPI mode uses less pins but is slower while 8-bit mode uses more pins and is faster, the choice is up to you. Adafruit have software and tutorials to support you whichever mode you decide to use, see the links below. The board also has a micro-SD card socket that you can use to store files and images.

Imagine what you could do with this if only it had a touch screen. Of course you don"t need to imagine, because the display has a built-in resistive touch screen. Because it uses resistance to detect touch, this screen will work with a finger, a stylus, the non-writing end of a pen or even a gloved finger. Anything that can put pressure on the screen will register a touch. The touch screen uses a further 2 x digital pins and 2 x analogue inputs regardless of whether you use SPI or 8-bit mode to drive the display.

Visit https://learn.adafruit.com where Adafruit provide a free tutorial for the Raspberry Pi, and another tutorial for the Arduino. They also have an open source library to drive the display in 8-bit mode, and another to use SPI mode. Please note that while the screen is capable of 18-bit colour, the Adafruit code uses 16-bits for efficiency. It"s highly unlikely that you"ll ever notice any difference.