8 inch tft lcd module in stock

ER-TFT080-1 is 800x480 pixels 8" color tft lcd display with OTA7001A driver IC,optional capacitive touch panel with controller and connector,optional 4-wire resistive touch panel with connector,superior display quality,super wide view angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO, ARM and Raspberry PI.Equivalent with AT080TN64,AT080TN52.

ER-TFTM080-2 is 800x480 dots 8" color tft lcd module display with RA8875 controller board,superior display quality and easily controlled by MCU such as 8051(C51), PIC, AVR, ARDUINO, and ARM .It can be used in any embedded systems,industrial device,security and hand-held equipment which requires display in high quality and colorful image.

It supports 8080 6800 8-bit,16-bit parallel,3-wire,4-wire,I2C serial spi interface.Built-in MicroSD card slot.It"s optional for 4-wire resistive touch panel with controller and capacitive touch panel with controller,font chip, flash chip and microsd card. We offer two types connection,one is pin header and the another is ZIF connector with flat cable mounting on board by default and suggested.

Of course, we wouldn"t just leave you with a datasheet and a "good luck!".Here is the link for 8" TFT Touch Shield with Libraries, Examples.Schematic Diagram for Arduino Due,Mega 2560,Uno. For 8051 microcontroller user,we prepared the detailed tutorial such as interfacing, demo code and development kit at the bottom of this page.e.

Alibaba.com offers 1771 ips panel 8 inch tft lcd display products. About 73% % of these are lcd modules, 4%% are lcd monitors, and 1%% are gaming monitors.

A wide variety of ips panel 8 inch tft lcd display options are available to you, such as original manufacturer, odm and retailer.You can also choose from tft, ips and standard ips panel 8 inch tft lcd display,

VIS080TN02S is 8 inch TFT LCD display panel module model that adopts 4:3 TN type LCD with 800*600 resolution. CTP (Capacity Touch Panel) and RTP(Resistive Touch Panel) can be added according to user requirements.

This 8 inch LCD module is specially developed for industrial and automotive products, so it has a long life cycle. We can guarantee a stable supply of this 8″ LCD display panel module throughout the life cycle of customer’s products.

Based on the panel’s 4:3 display ratio, high stability and excellent storage and operating temperature range, this 8 inch LCD display module can be widely used in industrial instruments (meters), car display and other products.

We also provide 8 ” LCD module with 800*480,1024*600 and 1024*768 resolution products for your choice. If interested, please contact us for more information.

Other 8 inch TFT LCD Display Screen Module(LCM) models（800*600） that can be replaced by VIS080TN02S are EJ080NA-05B, TM080SDH01, AT080TN42, A080SN03 V0, etc.

The Transmissive polarizer is best used for displays that run with the backlight on all the time. This polarizer provides the brightest backlight possible. If you have a need for a bright backlight with lower power drain, transmissive is a good choice for this TFT LCD display.

Focus LCDs can provide many accessories to go with your display. If you would like to source a connector, cable, test jig or other accessory preassembled to your LCD (or just included in the package), our team will make sure you get the items you need.Get in touch with a team member today to accessorize your display!

Focus Display Solutions (aka: Focus LCDs) offers the original purchaser who has purchased a product from the FocusLCDs.com a limited warranty that the product (including accessories in the product"s package) will be free from defects in material or workmanship.

Our uart TFT LCD provide a easy solution for make a display between human and machine, with serial interface tft, you could communicate to the MCU only via 2 data lines, save the I/O pins of CPU. And prevent users to avoid the hassle of wiring.

It is smart tft lcd and could be applied to Internet of thing (IoT) or industrial electronics field. It is the best solution to replace the traditional tft LCD module.

The 1.8inch LCD uses the PH2.0 8PIN interface, which can be connected to the Raspberry Pi according to the above table: (Please connect according to the pin definition table. The color of the wiring in the picture is for reference only, and the actual color shall prevail.)

ST7735S is a 132*162 pixel LCD, and this product is a 128*160 pixel LCD, so some processing has been done on the display: the display starts from the second pixel in the horizontal direction, and the first pixel in the vertical direction. Start to display, so as to ensure that the position corresponding to the RAM in the LCD is consistent with the actual position when displayed.

The LCD supports 12-bit, 16-bit and 18-bit input color formats per pixel, namely RGB444, RGB565, RGB666 three color formats, this routine uses RGB565 color format, which is also a commonly used RGB format

2.We use Dev libraries by default. If you need to change to BCM2835 or WiringPi libraries ,please open RaspberryPi\c\Makefile and modify lines 13-15 as follows:

2. The module_init() function is automatically called in the INIT () initializer on the LCD, but the module_exit() function needs to be called by itself

Python has an image library PIL official library link, it do not need to write code from the logical layer like C, can directly call to the image library for image processing. The following will take 1.54inch LCD as an example, we provide a brief description for the demo.

The first parameter is a tuple of 2 elements, with (40, 50) as the left vertex, the font is Font2, and the fill is the font color. You can directly make fill = "WHITE", because the regular color value is already defined Well, of course, you can also use fill = (128,255,128), the parentheses correspond to the values of the three RGB colors so that you can precisely control the color you want. The second sentence shows Micro Snow Electronics, using Font3, the font color is white.

The demo is developed based on the HAL library. Download the demo, find the STM32 program file directory, and open the LCD_demo.uvprojx in the STM32\STM32F103RBT6\MDK-ARM directory to check the program.

image.cpp(.h): is the image data, which can convert any BMP image into a 16-bit true color image array through Img2Lcd (downloadable in the development data).