adafruit tft lcd display pricelist

Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available!

The 2.2" display has 320x240 color pixels. Unlike the low-cost "Nokia 6110" and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ILI9341 or compatible) can display full 18-bit color (262,144 shades!). And the LCD will always come with the same driver chip so there are no worries that your code will not work from one to the other.

The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as an ultra-low-dropout 3.3V regulator and a 3/5V level shifter so you can use it with 3.3V or 5V power and logic. They also placed a microSD card holder so you can easily load full-color bitmaps from a FAT16/FAT32 formatted microSD card. The microSD card is not included.

Of course, Adafruit wouldn"t just leave you with a datasheet and a "good luck!" - they"ve written a full open-source graphics library that can draw pixels, lines, rectangles, circles, text, and bitmaps as well as example code. The code is written for Arduino but can be easily ported to your favorite microcontroller! Wiring is easy, we strongly encourage using the hardware SPI pins of your Arduino as software SPI is noticeably slower when dealing with this size display. Check the example sketches for wiring help until we get a detailed wiring tutorial written!

This display breakout also features a 18-pin "EYESPI" standard FPC connector with flip-top connector. You can use a 18-pin 0.5mm pitch FPC cable to connect to all the GPIO pins, for when you want to skip the soldering.

As of November 2022 - Adafruit have updated this TFT breakout with a EYESPI connector to make cabling easier with an 18-pin FPC. They also used Adafruit Pinguin to make a lovely silkscreen. The board is otherwise the same size, pinout, and functionality.

Touch screengraphic LCD TFT display with a diagonal of 2.4" and a resolution of 320 x 240 px. It works with a voltage of 3.3 V and 5V, communicates through the SPI bus. In addition, there is a slot formicroSD memory cards on the board.

Screen based on a driver ILI934, has a built-in RAM memory, due to this fact the microcontroller will not have to control the display. The device can communicate in two modes: 8-bit and using the SPI bus. For 8 bit mode you must connect the eight digital data lines and four control lines. SPI requires only five lines, but is slower than 8-bit communication. In addition, to support the touch screen it is required to connect four additional pins.

The outputs are holes for the supplied goldpin connectors - 2.54 mm raster (for self soldering). They allow the connection of the display via wire or plug attached to the contact plate.

This lovely little display is the best way to add a small, colorful display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even with very little memory and few pins available!

The 1.44 ″ display has 128 × 128 color pixels. Unlike the low cost “Nokia 6110” and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display full 16-bit color using our library code.

The breakout has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3 / 5V level shifter so you can use it with 3.3V or 5V power and logic . We also had a little space so we placed a microSD card holder so you can easily load full color bitmaps from a FAT16 / FAT32 formatted microSD card. The microSD card is not included, but you can pick one up here.