raspberry pi small lcd screen brands

Raspberry Pi boards have revolutionized the electronics hobby world with their simple credit card-sized DIY computer kits. Today, almost anyone with a basic electronics assembly and coding knowledge could set up a Raspberry Pi system of their own.

In order to create a small computer of your own, all you need to have is a raspberry pi board, a display unit and a keyboard (optional). If you are able to find the perfect touch screen, you can create a great DIY computer of your own.

Today, we are going to list down all of the best Raspberry Pi compatible LCD screens available online. These screens are ranked and rated based on the following factors.

Rule of thumb, larger the better. The best of the LCD screens for a Raspberry Pi we got here have a 1080P high resolution and is a full touch screen. There are higher variants available as well but we believe that this is a standard benchmark.

The next important thing that you need to look for in a screen is its compatibility with the various systems that you may be using it other than the Raspberry Pi.

This refers to the ports and other connectivity options through which you can set up the screen to the board. It includes the standard HDMI pots to USB ports and even WiFi compatibility as well. Higher the number of I/O ports, the better

First on our list is an LCD touch screen straight from the official house of Raspberry Pi. It is a 7 inches large touch display that is specifically created for the Raspberry Pi board.

Though compatible with all the existing Raspberry Pi models, the hole line up for installation is good enough only for Raspberry A+, Raspberry B+, Raspberry Pi2

Next on our list is a screen by Kuman, one of the top manufacturer’s in the realm of hobby electronics. This one too is a 7 inches large TFT capacitative touch screen.

Yet another Kuman 7 inches HD Display Screen, this one is quite different from the previous Kuman display screen. That difference is not just in the screen resolution but in a wide range of other things as well.

Next on our list is 1 large 10.1 inches LED Display. The Elecrow HDMI supported LED display monitor supports all the old and new Raspberry Pi models like the Pi 4, 3, 2, and B, B+ models as well.

Apart from Raspberry Pi models, it is also compatible with PS3, PS4, WiiU and XBOX360 and can also be used for video, for car headrest and as a small display for medical equipment too

In this entry, SunFounder comes with a 10.1 inches large HDMI supported IPS LCD display monitor. It has a high resolution of 1280 X 800 pixels and also comes with a camera holder stand.

Next on our list is another SunFounder Raspberry Pi Compatible screen. This one is a simple 7 inches large LCD Display screen with built-in speakers too.

Next product on our list is from a brand called ELECROW. Their LCD screen comes with 5-inches size display and high-resolution picture. It is a resistive touchscreen monitor and comes with a touch pen for easy use.

This LCD touch screen is from SunFounder which has similar dimensions and aesthetical aspect as the previous 10.1 inches Screen by SunFounder and are essentially the same. This is just an older model of the same product.

The last but not least product from our list is a 7-inch LDC touch screen for Raspberry Pi. It supports mini PC like Raspberry 1B+ / 2B / 3B / 3A+/ 3B+/ 4B.

But it’s up to you to take the correct decisions as per your requirement. To make it happen, you must acquire some knowledge in technology stuff which becomes very easy for you to pick the right one.

Given below are some of the factors that most of the people ask for while purchasing the Raspberry Pi display kits. Get to know about them in detail to make a good choice.

So when you make a purchase, check whether the device is within your budget or not. If it so, then you can happily add the item to cart and wish for it.

But the problem arises when you are unable to afford the money or willing to use the item to fulfill your basic needs. For them, we provided the raspberry pi display kits that come with amazing features at very low prices. Read the product information to know which product best suits your requirements.

Display resolution or the modes is the number of distinct pixels in each dimension that can be displayed. It is controlled by many of the factors like CRT, flat-panel displays, and LCDs. If the resolution you opt is not compatible then the monitors will stretch and shrink to fit in the specified. It turns result in a great loss of the signal and quality.

Like regular displays, the raspberry pi displays make effective communication between the peripheral devices. For this, it makes use of the connectors. The most common connectors are HDMI, VGA & AV-input. Each of them is illustrated below.

In this section, we are going to show you exactly how you can connect your Raspberry Pi to an external display screen. First, let us look at how to connect it using an HDMI port

Using the HDMI port to connect a Raspberry Pi to the LCD screen is one of the simplest and easiest ways to go. Here, all you need to do is to take an HDMI cable and plug it on both sides of the devices. One end goes into the HDMI port of the LCD screen and the other one will go right into the Raspberry Pi’s HDMI port. This set up does not require any special drivers software nor does it require any format of post plugin set up.

Raspberry Pi comes with a tiny 15 pin ribbon cable connector that can support a Display Serial Interface or a DSI standard. This enables fast communication between an LCD screen and the chip.

You can use the Raspberry Pi 7 inch touchscreen display by connecting it with the Raspberry Pi board. All you need to do is to first attach the raspberry pi to the back of the display screen using standoffs and screws that come with the kit.

Now connect the Pi board to the ribbon cable and the display control board. Note the ribbon cable pin orientation is proper or not. After this, carefully release the tabs on both sides of the socket so that the cable slides all way. Now secure this by pressing down on the tabs till you hear a click of a lock. Make sure you are not forcing the cable to lock.

If not, you can simply connect a power supply to the control board and then connect a small micro USB cable in the control board’s USB port and the micro USB port of the Pi. This should power on the device. You are now done setting up the device and the screen and once the power flows, the device boots up.

If the screen does not automatically turn on when the power source is connected, you may have to connect an existing HDMI display for updating your Raspberry Pi board and then reboot the device.

The Raspberry Pi 7″ Touch Screen Display from the house of Raspberry has a great colour output of 800 x 400 pixels and its capacitive touch is multi-fingered up to 10 fingers. That and the fact that it is specifically built for Raspberry pi Boards by the Raspberry company makes it the best Raspberry Pi LCD screen for your DIY Raspberry pi kit.

While those were our picks, we are intrigued by your choices, thoughts and opinions. Did we miss out on anything? Or do you want us to add anything else to this list? If so or if you have any questions for us or about the products mentioned, feel free to write to us in the comments section below. Our product expert team will write back to you as soon as possible.

raspberry pi small lcd screen brands

If you"re looking for the most compact li"l color display for a Raspberry Pi B+, Pi 2, & Pi 3 (most likely a Pi Zero) project, this might be just the thing you need!

In honour of Raspberry Pi"s 10th birthday, we"ve fused a RP2040 microcontroller with an EPD display to make a stylishly monochrome, maker friendly, e-paper badge(r)...

Pico Inky Pack features the speedy 2.9" e-paper display that you can find on Badger 2040, coupled with three handy buttons for interfacing. Equip it to the back of your...

Waveshare 21435 - 2.8″ Touch Screen Expansion For Raspberry Pi Compute Module 4, Fully Laminated Display, Gigabit Ethernet, USB2.0, Optional Interface Expander

In honour of Raspberry Pi"s 10th birthday, we"ve fused a RP2040 microcontroller with an EPD display to make a stylishly monochrome, maker friendly,...

Crisp, high-res, with great viewing angles (IPS), this 1.3" square, 240x240 pixel, colour LCD will add some pizzazz to your Raspberry Pi or Arduino projects.

A handy little cable that connects to the JST connector on the underside of HyperPixel 4.0, allowing you to use I2C devices with your Raspberry Pi at the same time as the display.

raspberry pi small lcd screen brands

The official Raspberry Pi 7” Touchscreen allows you to add touch inputs to your programs, creating a new way to interact with your projects. It also makes for a fantastic desktop screen for day-to-day use of your Raspberry Pi. Wrap it in one of our screen cases and take it anywhere – events, Raspberry Jams or even just your friends house for a coding evening!

For smaller projects, LCD and ePaper displays are a fun way to add a visual element to your projects. With simple code and wiring, they’re great for projects that require text, menus and navigation.

raspberry pi small lcd screen brands

So you"ve already picked up the best Raspberry Pi kit, but you want to be able to actually see things, so you"ll need to find the best Raspberry Pi screen. Then, of course, you"ll need to find a display to use, regardless of whether you grabbed the Raspberry Pi 4 or even the Raspberry Pi 400. So we"ve rounded up the best options to give your mini computer a display worth using.

Flexibility is the name of the game with a Raspberry Pi, so you"ll want the same from a monitor. With the ASUS VP28UQG, that"s exactly what you"re getting thanks to the 4K/UHD monitor, along with Adaptive Sync, dual HDMI ports, and a DisplayPort. It will also work magnificently if you want to hook it up with your PC and use it for your traditional AAA games instead of relying on your Pi.

The SunFounder 13.3-inch Raspberry Pi display is unique, as portable monitors are invaluable pieces of tech. This works with all Raspberry Pi models, but it will also work with your Xbox, PS5, Nintendo Switch, and even your PC if you need it to. The IPS panel provides a 1920 x 1080 resolution, and SunFounder even includes a couple of USB and HDMI cables in the box.

Raspberry Pi has made a 7-inch touch screen display of its own and sports a resolution of 800x480 and multi-touch support. There are just two connections needed to make from the display to the Raspberry Pi board for easy installation. Raspberry Pi also includes an adapter board that will take care of the power, signal conversion, and touch input.

It is specifically designed for the Raspberry Pi, so you only need to plug it in, and you"re up and running. This multi-touch display works with the 4B, 3B+, and 3B, or it can work with your existing computer as an additional monitor. There"s a 3.5mm headphone jack and an included micro-HDMI adapter so you can get everything up and running quickly.

It"s a case with its own 3.5-inch 320x480 TFT monitor built into the top. So carry a computer everywhere in the palm of your hand. Jun-Electron also includes a built-in fan to help keep both the Raspberry Pi and monitor cool when in use.

This 4-inch LCD from Miuzei gives you easy access to all your ports while the display is mounted on top. The monitor itself supports a resolution up to 800x480, which is likely way too high for a display this small, but the refresh rate comes in at 60FPS, which is still pretty nifty.

This 7-inch capacitive display has a 1024x600 resolution and connects via HDMI. It also only requires 500mAh of power for its backlight. There are two additional USB ports for you to take advantage of and expand and extend. Plus, you won"t have to worry about meddling around with any display drivers and can just plug and play this GeeekPi monitor with your Raspberry Pi.

This 10-inch display comes with its own stand and has dual speakers, so everything sounds as good as it looks. Not only is it compatible with the Raspberry Pi suite of products, but this display will also work with your computers and gaming consoles.

After you"ve picked up one of the best Raspberry Pi kits, the next move is to secure a great screen. And the Raspberry Pi is no slouch when it comes to video. With the current model supporting dual 4K monitors, it has the power to drive just about any screen. While you"re home, you can use a larger monitor or television, but for something more portable, we like the GeeekPi 7-inch Raspberry Pi Display. If you need a small display for your Raspberry Pi and don"t feel like working through set up files or carrying a special high-power charger to run it, you"ll love it too.

Those wanting to push the limits of their Raspberry Pi will want to check out the ASUS VP28UQG. This display features up to a 4K/UHD resolution, two HDMI ports, and a single DisplayPort, along with ASUS" Eye Care Technology to keep your eyes from getting too strained when you"re staring at the screen for too long. While this doubles as the best Raspberry Monitor, it will also work perfectly if you want to hook it up to your PC thanks to the AMD FreeSync support built-in.

raspberry pi small lcd screen brands

Raspberry Pi OS provides touchscreen drivers with support for ten-finger touch and an on-screen keyboard, giving you full functionality without the need to connect a keyboard or mouse.

The 800 x 480 display connects to Raspberry Pi via an adapter board that handles power and signal conversion. Only two connections to your Raspberry Pi are required: power from the GPIO port, and a ribbon cable that connects to the DSI port on all Raspberry Pi computers except for the Raspberry Pi Zero line.

raspberry pi small lcd screen brands

There are tons of products on the market for Raspberry Pi Screen and most of them are probably good. But the question is does the product fulfills your needs or not. Every product has its own pro and cons. A good product for someone else might not be your perfect fit because you may have a different requirement.

Apart from pros and cons, there are some basic factors that you must verify before you make a purchase. These factors remain equally important for everyone. That is why we have prepared this Raspberry Pi Screen buying guide for you so that you can make your purchase with confidence.

【Multi Application Portable Monitor】Broadly you can use it with your Raspberry Pi 4/3/2/1/3B+/BB,Banana Pi. Windows 7/8/10 PC, Microsoft, TV. Video game console like NS Switch/XBOX/PS4. Other devices or systems like Retro Pi, NOOBS, Debian, Ubuntu and Kodi are all supported. Note: The HDMI-HDMI Cable is for Raspberry PI 3. If you need to use it for Raspberry PI 4, please buy an Micro-HDMI-HDMI Cable. This screen does not come with a case, but with a bracket.

【Plug-n-play & Portability】Simply connect the screen to device via HDMI interface and power the USB port to achieve function and no need to install any driver.This is great for people who want to use the screen for their own DIY projects. The portable hdmi monitor is light and easy to carry.

【Versatile Digital Connection】Raspberry pi display for HDMI, micro USB make it easy connection with Laptops, PCs, Gaming Devices great ideal for extending your screen or playing games on business trip, travel, or home entertainment.

【Three Application Modes for Laptop】Duplicate mode, extend mode and second screen mode. Each mode has different use effects, bringing convenience and leisure to your work and life. Right click display settings on your laptop desktop, and then select three different usage modes in the multi display settings bar according to your needs. Go and get a laptop monitor now and feel a different experience.

【Raspberry Pi Screen Monitor】HMTECH 7 inch raspberry pi monitor adopts tempered glass and full bonding process. It is equipped with IPS screen and 800 * 480 resolution, 178 ° viewing angle. The IPS panel color is accurate, showing more vivid color and contrast than VA and TN displays.

Miuzei Raspberry Pi 4 Touchscreen with Case Fan, 4 inch IPS Touch Screen LCD Display, 800x480 HDMI Monitor for RPI 4b 8gb/4gb/2gb with Touch Pen (Support Raspbian/Kali/Octopi/Ubuntu)- No Raspberry Pi

Orange Pi Touchscreen - Miuzei raspberry pi 4 monitor support HDMI audio output, data entry (computer, DVD), HDMI audio input, stereo 3.5mm audio output.

Packaging Content & After Sales - you will receive raspberry pi screen, raspberry pi heatsink, 30mm cooling fan, screwdrive, awesome looking, it can make your lcd display case looks cooler than others. if you encounter any problems, you can contact us at any time, and we will answer you.

Raspberry Pi 4 Screen Case - Pi 4 inch touch screen compatible with raspberry pi 4 b/4b/4 model b. Display ONLY Support System - Raspbian, Kali-linux, Ubuntu, Octopi.

Touchfunction Support System - only support Kali, Raspbian, Ubuntu, Octopie. The 4 inch display monitor with touch control function (need to install touch drive), we offer pre-install driver system image file. could be used as standard HDMI output device for computer display (no touch function).

Raspberry Pi 4 Touchscreen - Raspberry Pi 4 Inch IPS full-angle display monitor, 800 x 480 physical resolution support HDMI input, refresh rate up to 60fps.

Only two connections from the Pi TO the Display are necessary; power from GPIO (or USB) connection to the DSI port. The adapter board handles power, Signal conversion, and touch input conversion.

This 7" Touchscreen display for the Raspberry Pi is perfect for creating portable and embedded projects where a keyboard and Mouse would be in the way.

The display is equipped with 2 damping shaft brackets, the display angle can be adjusted arbitrarily, and the brackets can also be removed to install the case. The STL file for the 3D printed case is available under eleclab-rpi/7INCH_DSI_DISPLAY, and the fan case STL file is under eleclab-rpi/rpi_fan_case.

DSI interface 7-inch LCD 800x480 resolution and 5-point capacitive touch screen, display brightness can be adjusted by potentiometer and software PWM, integrated audio amplifier and 2W dual channel stereo speakers and volume potentiometer.

This display only supports the Raspberry Pi DSI interface, and the Raspberry Pi can be easily installed on the back of the monitor through 4 positioning holes. The display provides power to the Raspberry Pi through the power adapter board, and the two XH2.54 sockets can supply power to fans or other peripherals.

PLUG & PLAY AND GREAT COMPATIBILITY - With this USB monitor you can start your projects without having to download and install any drivers. You can use it with your Raspberry Pi 4/3/2/1 / 3B + / BB, Banana Pi. And the monitor is suitable for Windows 7/8/10 PC, Mac, Microsoft, Media Players, FireTV stick and AppleTV, video game consoles such as Nintendo Switch / XBOX / PS4. Other devices or systems like Retro Pi, NOOBS, Debian, Ubuntu, and Kodi are also supported.

DUAL BUILT-IN SPEAKERS - Designed with dual integrated speakers, this monitor combines incredible screen performance with stereo sound for an immersive multimedia experience. Thanks to the two built-in speakers, you don"t need an external speaker when working on a Pi project.

COMPLETE ACCESSORIES, PERFECT FOR ALL VERSIONS OF THE RASPBERRY PI - The supplied Micro HDMI cable makes the connection between the monitor and Raspberry PI4 easy. If you have other Raspberry PIs, the standard HDMI cable can help you too. We also supply a monitor stand with screws. It can be installed without any problems.

5 POINTS CAPACITIVE TOUCH + EXCELLENT IMAGE PERFORMANCE - Thanks to the excellent sensitive capacitive technology and the multi-touch function, you can swipe, scroll, select, zoom, and zoom across the screen in just 3 to 5 ms. Equip with IPS screen with HD 1024*600 high resolution, supports up to 1920*1080 and 640*480, the display with 178°viewing angle and adjustable brightness (max 300 cd/m²) and contrast (max 700:1) offer you the ultimate project experience.

UNIQUE DESIGN AND PORTABLE - The screen without case and frame, you can mount your Raspberry Pi on the back of the display and remodel this mini monitor directly. This is great for people who want to use the screen for their own DIY projects. With the original stand, the display can stand directly on the table. The portable monitor is light (ONLY 165g) and easy to carry.

Upgraded Raspberry Pi Screen Monitor, HAMTYSAN 7 Inch Portable Monitor External Display 800x480 IPS Screen Small HDMI Monitor for Raspberry Pi 400/4/3/2/Zero/B/B+ Jetson Nano Win10/8/7 (Non-Touch)

【Widely Compatible】Specially designed for Raspberry Pi, HAMTYSAN small monitor is perfectly suited for all versions of Raspberry Pi including Raspberry Pi 4/3/2/1/3B+/BB/400.Other devices like Octo Pi, Banana Pi,Retro Pi, game consoles( NS / XBOX / PS4),CCTV, laptop, TV boxes etc.The HDMI portable monitor also great compatibility with various OS such as Windows, Noobs, Debian, Ubuntu, Kodi.

【HDR Mode & 3-in-1 Display Modes】HDR mode supports excellent mainstream transmission so that you can enjoy unprecedented performance. The LCD Pi monitor can effectively reduce blue light radiation damage, no flickering, and make it easier to watch for a long time.Use the laptop to set three modes: duplicate mode, extend mode and second screen mode. Each mode has different use effects, bringing convenience and leisure to your work.

【Plug-n-play Portable Monitor】Simply connect the screen to device via HDMI interface and power the USB port to achieve function and no need to install any driver program or software.The screen without case and frame, convenient for you to better use and transform it.The portable laptop monitor is light and easy to carry,used as a mini second monitor for your pi or laptop.

【Unique Design】With a multi-angle adjustable bracket, the bracket groove is made of rubber, which protects the edge of the display well and supports the LCD screen display stably. This Raspberry pi display can be placed on a desktop, inside a computer case, on a wall, etc. It has four mounting holes on the back, which is great for anyone who wants to use the screen for their own DIY projects.

【Raspberry Pi IPS Screen】7 inch mini monitor, support 800*480 resolution, 3-5 ms response time,IPS screen help keep colors consistent at a 178°wide viewing angle. Our raspberry pi monitor adopts tempered glass and full lamination technology,compared with traditional technology, its function is to make the image more clear and transparent, and play a role in preventing dust.It will bring better screen display effect.

ELECROW Raspberry Pi Touchscreen Monitor 5 inch HDMI Screen Display 800x480 Compatible with Raspberry Pi 4 3B+ 3B 2B BB Black Banana Pi Jetson Nano Windows 10 8 7

4. Can be used as a general-purpose small HDMI screen, connecting computers, TV boxes and game consoles, or mounted inside your PC case as computer temp monitor, etc.

1. 5 inch small HDMI monitor with 800x480 mini LCD screen. The touchscreen is USB capacitive touch control, free-driver, plug and play, micro USB interface for touch and power supply, HDMI interface for displaying.

3. Can be worked as a Raspberry Pi screen, compatible with the latest Raspberry Pi 4, 3 B+, BB Black, Banana Pi, Jetson Nano and other mainstream mini PC.

ElecLab Raspberry Pi Touchscreen Monitor 7.4 Inch HDMI Capacitive LCD Display 1280x400 Speaker Case for Raspberry Pi 4B 3B+ 3B 3A+ 2B B+ (7.4inch 1280x400)

This display is suitable for Raspberry PI 1 model A+ B+/ PI 2 model B/PI 3 model A+ B B+/PI 4 model B. The Raspberry Pi board can be installed through the 4 positioning holes on the back of the display.

ROADOM Raspberry Pi Touchscreen Monitor,Upgraded 7"" IPS 1024X600 Dual-Speaker,USB HDMI Portable Monitor Capacitive Pi Display,Compatible with Raspberry Pi 3b+/Raspberry Pi 4b, Windows,Drive-Free

【We stand behind our products】ROADOM 7inch touch screen monitor comes with great customer service. For any doubt about this 7inch Touchscreen Raspberry Pi display, feel free to contact us. All customer online messages and emails are replied within 24 hours.

【Unique Portable monitor for Raspberry Pi】Raspberry Pi hobbyist couldnot miss this unique designed Raspberry monitor! Easily mount your Pi to the back of this 7in touch screen monitor. Four corner holes let you mount the small monitor onto your DIY IoT projects that you’re working on. This Raspberry Pi display also comes with 2 stands, easy to install and remove, great for on-the-go use.

【Plug n Play, Widely Compatible】ROADOM 7 inch USB monitor is 100% plug & play. Signal via HDMI port, power&touch via mivroUSB port, drive free. Compatible with Raspberry Pi 4/3/2/1, Windows 7/8/10 PC, Mac, TV, video game console like NS/XBOX/PS4. Other devices or systems like Retro Pi, NOOBS, Banana Pi, Debian, Ubuntu and Kodi are all supported. *Need an extra HDMI adapter for Pi4.

【Responsive Touching】ROADOM 7 inch touchscreen monitor is equipped with 5-point capacitive touchscreen. This Raspberry Pi display supports multi-touch gestures. The seamless bezel makes it easier to swipe in from the side of the small monitor. Check if your Raspberry Pi or other devices support touch interaction before using.

【Excellent Color with IPS HD Panel】With IPS HD panel, ROADOM 7 inch monitor presents horizontal & vertical 178° full viewing angle and accurate color, displaying more vivid colors and contrast than VA and TN monitors. Touch screen resolution is 1024*600 and it supports up to 1920*1080. Note: Please remove the screen protector before use to present more vivid image.

HMTECH Raspberry Pi Screen 10.1 Inch Touchscreen Monitor 1024x600 Portable HDMI Monitor 16:9 IPS Screen Display for Raspberry Pi 4/3/2/Zero/B/B+ Win10/8/7, Free-Driver

Three Display Modes for Laptop -- Duplicate mode, extend mode and second screen mode. Each mode has different use effects, bringing convenience and leisure to your work and life. Right click display settings on your laptop desktop, and then select three different usage modes in the multi display settings bar according to your needs. Go and get a portable laptop monitor now and feel a different experience.

More Application HDMI Monitor -- Broadly you can use it with your Raspberry Pi 4/3/2/1/3B+/BB,Banana Pi. Windows 7/8/10 PC, Microsoft, TV. Video game console like NS Switch/XBOX. Other devices or systems like Retro Pi, NOOBS, Debian, Ubuntu and Kodi are all supported. Note:The attached HDMI cable is only applicable to devices with standard HDMI interface. If you need to use it for Raspberry Pi 4, please buy an Micro-HDMI-HDMI Cable. This screen does not come with a case, but with a bracket.

Plug-n-play Raspberry Pi Display -- Simply connect the screen to device via HDMI interface and power the USB touch port to achieve touch function and no need to install any driver. The monitor is fairly standard in size and shape without manual calibration. The screen resolution can also be adjusted setting according to the user"s requirements.

Raspberry Pi Touchscreen Monitor -- 10.1 inch Raspberry Pi monitor equip with IPS screen and HD 1024*600 high resolution, ensure the touch monitor more precise color restoration exquisite picture quality and more rich color. 178° viewing angles is more ideal for work and for reviewing on-screen with multiple people in the room.The monitor adopts tempered glass and full bonding process.

Easy-use for Touch Screen -- Excellent sensitivity capacitive technology and multi-touch capability allows you to swipe, scroll, select, zoom in, zoom out, and move a cursor about in just 3-5 ms. Touchscreen drivers with support for 5-finger touch and an on-screen keyboard are integrated into the Raspberry Pi OS for full functionality without a physical keyboard or mouse.

Match PC Protective Case for your screen and Pi, use split design make it easy to install, also match tweezers to make install more easy. White nylon column can help screen maintain balance.

The screen Display support 125MHz SPI signal input, it can display stable without flicker, the refresh rate is about 50fps, it’s enough to play the video and game.

Physical resolution 320x480 with resistive touch control, can be directly connect Raspberry Pi 3 B+ , No additional Power. (Raspberry Pi is not included)

The screen need install driver, otherwise screen ONLY show white. If you don’t how to install driver, Please try the Pre-install Driver System to test screen working statues

New Design Screen built-in fan which can drop temperature quickly, and keep your Pi Cool when working. The case is compatible with raspberry pi 4 perfectly.

UCTRONICS 7 Inch IPS Touch Screen for Raspberry Pi 4, 1024×600 Capacitive HDMI LCD Touchscreen Monitor Portable Display for Raspberry Pi 4 B, 3 B+, Windows 10 8 7 (Free Driver)

Wide Compatibility: compatible with Raspberry Pi 4B/3B+/3B and all other Model A&B series, can also work as a general-purpose compact touchscreen monitor. Please search ASIN B085MY9HNX to get the screen with stand.

Video-audio Joy: 1024 x 600 pixels high resolution (support up to 1920 x 1080 input and auto-scaling). 178° wide viewing angle and adjustable backlight make sure high visual quality; 3.5mm audio/headphone jack makes the display no longer silent.

UCTRONICS Mini LCD Screen with Case for Raspberry Pi 4, 3 B/B+, 3.5 inch Small HDMI Display Touchscreen with Stylus, Compatible with All Raspberry Pi B Models

Wide Compatibility: The case is designed to perfectly house Raspberry Pi 4 B, 3 B/B+ with the small touch screen. NOTE: Raspberry Pi motherboards are not included.

Effective Cooling Design: It comes with a copper heatsink for the CPU, the display board is mounted a 25mm×25mm brushless quiet fan, and cuts for air outlets, all of them cool your pi 4 effectively.

Plug & Play: Don"t need to reboot the Pi when connected, it doesn"t require any external power supply, and it displays with no need of driver. Please note the touch function needs to install the driver.

Lightweight and Portable: the overall dimension of this tiny screen with enclosure is 3.66" ×2.48" ×1.18", and the delicate design and mini stylus make this kit completed and convenient to use.

kuman 5 inch Resistive Touch Screen 800x480 HDMI TFT LCD Display Module with Touch Panel USB Port and Touch Pen for Raspberry Pi 3 2 Model B RPi 1 B B+ A A+ SC5A

When the 5 inch monitor work with RPI, it don"t need external power supply. This screen power supplied and can be touched by GPIO, display by HDMI. If it is powered by external power, there will be no touch function, and please use 5V2A power supply to power it.

This HDMI raspberry pi display is with 800 x 480 resolution, we design a protective case for it, and it need you to assemble it, You could look for the below QA to download the tutorial or contact us by email to get.

[Plug and Play Feature] The USB C portable monitor has impressive feature of plug and play that doesn’t require any driver installation. Compatible with thunderbolt 3. Support mirror and split screen mode, increase your productivity and your gaming pleasurable, great choice for dual monitor or third screen

[Ultra Portable Monitor] 15.6” Matte Monitor delivers stunning 1920 x 1080 resolution, IPS screen with ultra HDR option, design for portable with only net weight 1.42lb and 0.39 inches slim, make it easy to carry, handy, best for travelling

GeeekPi Raspberry Pi 4 TFT 3.5 inch Touch Screen with Case, Raspberry Pi Fan and Heatsinks, 320x480 Resolution LCD Display for Raspberry Pi 4 Model B (Raspberry Pi Board NOT Included)

Package includes: 1x ABS Case for Raspberry Pi 4B, 1x 3.5 inch TFT resistive touch screen, 1x Aluminum heatsinks, 1x Touch Pen, 1x 30x30x7mm cooling fan (NOTE: this fan can not be installed with 3.5 inch screen at the same time)

This kit contains an ABS case and a 3.5 inch resistive touch screen. It’s fully compatible with Raspberry Pi 4 Model B. NOTE: Raspberry Pi Board NOT Included! The fan and screen can not be installed at the same time.

The 3.5 inch resistive touch screen can be directly inserted into any version of the Raspberry Pi boards, but the ABS case is only compatible with Raspberry Pi 4B; The resolution of 3.5 inch touch screen can be adjusted by software; The screen support 125MHz SPI signal input, the refresh rate is about 50fps which is enough to play the videos or games and display stable without flicker; It supports Raspbian, Ubuntu, and Kali system, the drivers and image are provided freely.

The cost of Raspberry Pi Screen depends on a few things, like the quality of the product, finishing, brand, popularity, etc. You don’t want to buy an overpriced product for no reason. Likewise, you don’t want to buy a cheap product which has very poor quality.

The ideal cost of a product should be within an average buyer’s reach without compromising the quality. Materials used to make the product should be standard; finishing should be premium while keeping in mind the cost.

Don’t just trust a brand/product just because it has a good reputation. Always make sure to look into the materials used to make the Raspberry Pi Screen. You certainly don’t want materials that are low quality or harmful to you or to nature.

To end things off, you are ready to purchase your Raspberry Pi Screen without a second thought. We hope that we were able to clear out the confusing parts of these products. Additionally, help you with the factors that you need to keep in mind while getting one in the first place with the buying guide.

raspberry pi small lcd screen brands

When you want to have an easier time of connecting to different media and selecting it, a single-board computer is an efficient option. The Raspberry Pi single-board computers work with a variety of peripheral devices, including LCD display modules with touchscreens. On eBay, you can find a variety of sizes and features of affordable Raspberry Pi touch screen units to pair with the single-board computer for enjoying your favorite media.What are some features of Raspberry Pi Touch Screen modules?

Automatic power off: If the touchscreen is not used within 10 minutes, it automatically powers off. This time can be adjusted to turn off in less or more time.

Signal support: It accepts EGA, SVGA, WXGA, VGA, SXGA, and UXGA video signals from the computer.What are the sizes of Raspberry Pi touch screen modules?

The Raspberry Pi touch screen modules are available in sizes of three to seven inches when measured on the diagonal. Their frames can be set up in a vertical or horizontal orientation for viewing in a portrait or landscape setup. The stands for the touchscreens can also be angled for easier use and viewing. See the manufacturer site for details.What is the compatibility of a Raspberry Pi display module?

The following are compatibility options for a Raspberry Pi touch screen display module:USB: They can display the information that is stored on a removable USB drive plugged into the Raspberry Pi computer.

Consider the following features when you are shopping on eBay for a new or used Raspberry Pi touch screen:With computer case: Some have a case for holding both the computer and the display in one unit.

raspberry pi small lcd screen brands

All fans of Raspberry Pi perfectly understand the phenomenon of Raspberry, which has enthusiasts in many areas. It is used in everyday life, but also in robotics, programming and industry. Raspberry Pi is perfect for modern intelligent building systems. It can be expanded with various types of peripheral devices, acquiring specific features. Among them there are displays, which are available in our offer in different versions. They come in 0.9", 1.3", 1.44", 1.54", 2", 2", 2.13", 2.2", 2.4", 2.6", 2.7", 2.8", 3.2", 3.5", 4", 4.,2", 4.3", 5", 5.83", 7", 7.50", 10", 10.1", 11.1" and 14" screens. They also differ in the technology used, which ensures a specific image quality. We offer LED and OLED matrix displays, monochrome and segmented, consisting of LEDs, e-paper, alphanumeric displays as well as LCD IPS, LCD TFT. The displays work with boards using GPIO+DPI, HDMI, HDMI+GPIO, HDMI+USB, DSI, GPIO, I2C, SPI, SPI + I2C, as well as USB. The interface through which the screen connects to the Raspberry Pi module must be operable, otherwise there is a risk of interference and the connection quality will be poor.

We offer screens dedicated for special housings as well as modular laptops based on Raspberry Pi. If you use the display and your Raspberry frequently, an e-paper display is a good choice for you, which is more convenient for human eyesight. It has other advantages, it is very energy-efficient, consumes little energy, so it will be a good choice for those who are still looking for savings, while increasing the comfort of their daily life.

The displays can be used on a daily basis as well as for large robotics and electrical projects. They can be used for information purposes, displaying current data with the parameters of the specific equipment or system with which they work. This function is very often performed by monochrome and segment displays. Or maybe you would like to create your own e-book reader. You will need an energy-saving and eye-safe e-paper display. Touchscreens are very well suited for game controllers and drawing devices. The use of Raspberry Pi displays is therefore very wide.

Adjust the type of display to your design and purpose. Decide on the option that best matches your expectations and needs. Build your Raspberry Pi, make an ambitious project or simply use the Raspberry Pi as an alternative to your laptop or iconic PC.

raspberry pi small lcd screen brands

Touch screen monitors and touchscreen displays are everywhere. Just look around and you"ll notice a raspberry pi display or an LCD display within close proximity to you, (most likely, in the form of a smartphone).

An raspberry pi display, or liquid crystal display touch screen, is a display that can recognize a user"s touch through either resistive or capacitive sensing. This technology is probably one of the greatest technological innovations to hit the consumer market and is now an essential element of popular devices and brands across the globe. Thin film transistor (TFT) touch screens and displays have also improved consumer electronics and made this tech more accessible to everyday users.

A TFT touch screen combines the fundamental elements of a raspberry pi display with the advanced imagery TFT technology. These are the variants of raspberry pi display displays that most consumers see and use on a daily basis. While TFT displays use more energy than standard monochrome LCD displays, many models provide brighter and more detailed visuals than conventional screens.

As a popular technology that is now embedded in numerous devices, demand for touch screen LCD displays and related accessories like touch screen controllers is likely to grow. If you"re looking to sell to consumers, retailers, or other businesses, then Alibaba.com is a great choice to source wholesale monitors in bulk.

raspberry pi small lcd screen brands

Thanks for bringing this to my attention. It appears that the upgrade package overwrites the FBTFT drivers, in particular, the Raspberry Pi bootloader. This seems to solve the problem:

I just tested this, and it looks like the difference is how SPI is enabled. In the RPi 2 it’s enabled in raspi-config, not commented out in the blacklist file. I just updated the post so it should work now!

Looks like the only difference is in how SPI is enabled. In the new release of Raspbian, SPI is enabled in the raspi-config menu under advanced settings. In older versions of Raspbian, it is enabled by commenting out the line in the blacklist file

dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p6 rootfstype=ext4 elevator=deadline rootwait fbtft_device.custom fbtft_device.name=waveshare32b fbtft_device.gpios=dc:22,reset:27 fbtft_device.bgr=1 fbtft_device.speed=48000000 fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo dma.dmachans=0x7f35 console=tty1 consoleblank=0 fbtft_device.fps=50 fbtft_device.rotate=0

Unfortunately, their “driver” is an SD card image containing a complete installation of Raspbian which has been preconfigured to use their display. Which is fine if you’re setting up a brand new system that doesn’t need to be a specific distro, but if you’re trying to add the display to an existing Raspberry Pi, already configured the way you want it, with software installed and data present, or if you want to use a specific distro such as Octopi, then it’s not terribly helpful.

Hello..I tired to interface this lcd “https://www.crazypi.com/raspberry-pi-products/Raspberry-Pi-Accessories/32-TOUCH-DISPLAY-RASPBERRY-PI” to my Raspberry pi model B+.I got a DVD containing image for LCD in the package.I burned it to the SD card and plugged in the display.But my lcd is completly blank.But green inidcation led (ACT LED) in board is blinking.Why my LCD is Blank ?

If you have tried using the manufacturers image and the screen doesn’t work, it could be that the screen has a hardware malfunction. If the process above doesn’t work either, I would contact the manufacturer

Is your RED (POWER) LED on? I had the same problem. Green Led was blinking and screen was white. Then I noticed RED Led is off, indicating there’s something wrong with the power. I plugged into different port and it started

Yes, it may be that the screen isn’t supported. Newer screens might not have drivers yet. I do know it is possible to make your own driver but that’s above my level of knowledge :)

My Touchscreen is now working fine.The problem was for the ribbon cable on the back side of LCD.It was not connected properly.I just tighted the cable and it worked fine.Hope it will be useful tip.

Thank you for this great tutorial. I looked everywhere for this information. I have an eleduino 3.5 version A. I was able to get it working on my Pi 2 by following your tutorial and using flexfb as the screen type. I got the other settings from the image that came with the product. I did find that the ts_calibrate didn’t recognize the screen so I installed xinput-calibrator and it worked fine.

Just got my Pi2 running Wheezy, working with the Eleduino 3.5 LCD without running the OEMs image… kinda. I didn’t want to rebuild the application environment again, so was avoiding flashing the SD.

I tried the steps in this tutorial. It’s very clear and easy to follow, thank you. But it didn’t work for me, I tried setting my device to flexfb. Only got white screen.

Unzipped it and looked around. From a shell script inside i kinda figured out what it was doing. I didn’t like what I saw, so I manually made changes omitting the parts I didn’t like (it rm -r my /lib/modules directory… omitted that part) and copied 2 files and 1 directory from the OEMs archive to the file system of my Pi2.

[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa21041 bcm2709.serial=0x631a4eae smsc95xx.macaddr=B8:27:EB:1A:4E:AE bcm2708_fb.fbswap=1 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait fbtft_device.custom fbtft_device.name=flexfb fbtft_device.gpios=dc:22,reset:27 fbtft_device.bgr=1 fbtft_device.speed=48000000 fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo dma.dmachans=0x7f35 console=tty1 consoleblank=0 fbtft_device.fps=50 fbtft_device.rotate=0

thank you for your great tutorial, it got me on the right way. unfortunataly i only see some boot messages on the lcd and then it turns black. maybe you could give me a hint on how to get it working entirely.

i have a watterott display (https://github.com/watterott/RPi-Display) and changed the device-name to “rpi-display”. i use a rsapberrypi 2 and hae the latest raspian image installed.

Did you check to see if your device is supported yet? The device name should be specific for your screen, as listed in the fbtft file linked to in the beginning of the post

I too have a raspberry pi 2, and a waveshare spotpear 3.2 RPi lcd (v3) and I just can’t get it to work! I suspect I have a faulty LCD, but thought I’ll try this forum for help before I sent it back.

Soon as the pi is powered, the LCD lights up all white, with a few vertical pixels coloured at one of the edges, and nothing else. I don’t think that should happen – not at least before the BOIS has started up.

Anyway, point 1, says to change to dev/fb1 – I don’t have fb1. Only fb0 appears to be there. is that a clue what could be wrong? I have enabled SPI (is there a command to tell if its enabled?) I have also ran spidev to troubleshot (though I haven’t a clue what I means)

Any ideas what going wrong? I am using the latest “2015-02-16-raspbian-wheezy_zip”. Enabled SPI. done all the steps. Even changed mmcblk0p2 to mmcblk0p6 as suggested by Dabomber60 (but that freezes for me)

[ 0.000000] Linux version 3.18.5-v7+ (pi@raspi2) (gcc version 4.8.3 20140106 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2014.01 – Linaro GCC 2013.11) ) #1 SMP PREEMPT Fri Feb 6 23:06:57 CET 2015

It seems all appears to be working – just the LCD is still all white with a single line of coloured pixels on edge) and nothing else. Is there a way to output, like jeff G script, of touch points?

I had the same one, I finally found a driver for it here: http://www.waveshare.net/wiki/3.2inch_RPi_LCD_(B) you will need to translate the page, but unpack the driver then run sudo ./LCD-show/LCD32-show. It should reboot and all will be good with the screen :)

Can anyone let me know if the default OS image sent with the screen works with pi2 or just Pi B/B+ as i think my screen maybe broken but can’t confirm it yet as i have not had it working at all

My system: Raspberry Pi 2 Model B with Raspian Wheezy from Febuary 2015. LCD display of Sainsmart 3.2 http://www.conrad.de/ce/de/product/1283498/Raspberry-Pi-Display-Modul-Touch-Display-81-cm-32/?ref=home&rt=home&rb=1

dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 cgroup_enable=memory elevator=deadline rootwait fbtft_device.custom fbtft_device.name=sainsmart32_spi fbtft_device.gpios=dc:24,reset:25 fbtft_device.bgr=1 fbtft_device.speed=48000000 fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo dma.dmachans=0x7f35 console=tty1 consoleblank=0 fbtft_device.fps=50 fbtft_device.rotate=90

sainsmart32_spi width=320 height=240 buswidth=8 init=-1,0xCB,0x39,0x2C,0x00,0x34,0x02,-1,0xCF,0x00,0XC1,0X30,-1,0xE8,0x85,0x00,0x78,-1,0xEA,0x00,0x00,-1,0xED,0x64,0x03,0X12,0X81,-1,0xF7,0x20,-1,0xC0,0x23,-1,0xC1,0x10,-1,0xC5,0x3e,0x28,-1,0xC7,0x86,-1,0×36,0x28,-1,0x3A,0x55,-1,0xB1,0x00,0x18,-1,0xB6,0x08,0x82,0x27,-1,0xF2,0x00,-1,0×26,0x01,-1,0xE0,0x0F,0x31,0x2B,0x0C,0x0E,0x08,0x4E,0xF1,0x37,0x07,0x10,0x03,0x0E,0x09,0x00,-1,0XE1,0x00,0x0E,0x14,0x03,0x11,0x07,0x31,0xC1,0x48,0x08,0x0F,0x0C,0x31,0x36,0x0F,-1,0×11,-2,120,-1,0×29,-1,0x2c,-3

ads7846_device model=7846 cs=1 gpio_pendown=23 speed=2000000 keep_vref_on=1 swap_xy=1 pressure_max=255 x_plate_ohms=60 x_min=300 x_max=3800 y_min=700 y_max=3400

The LCD display shows the raspberry correctly. However, the touch screen input does not work. The mouse pointer can I move correctly with your finger, but I can not select things (function of the left mouse button).

Thank you so much for this great tutorial. I have my WaveShare SpotPear 3.2″ V4 working fine on my Raspberry Pi 2. If you are having problems with this specific hardware, skip step 5.

Can someone upload SD card image that works with RBP2 ? My idea is to use Eleduino TFT as additional screen and play movies via HDMI.. is it possible?

Do not follow this article when you don’t know what kind of LCD module. In my case, I follow all of this and my raspberry pi cannot boot anymore. I will try to recover, but I think I should format my SD card and reinstall OS.

Expecting this would builtin driver module within kernel and help with avoiding mistakenly overwriting anything. But with this is cause LCD screen to go blank white and no boot activity. Also noticed on HDMI it get stuck on Initial rainbow screen and stuck on that.

Also can you someone explain what exactly happen when do rpi-update? Want to understand what this step actualy doing and help me to debug any such situation and able to help others.

Does anyone tried splash boot screen with waveshare v4 LCD and Rpi2? I tried to follow some example from https://github.com/notro/fbtft/wiki/Bootsplash but no success.

Great tutorial thanks; got an X session working great 1st time. Has anybody managed to get Kodi/XMBC working on the LCD either Kodi standalone, Raspbmc or Xbian?

in the video you say to change the existing line to “snd-bcm2836” for the rasppi2 which isn’t listed in the written part of the instructions (part 4).. this should be added (I believe it caused me to have to re-image the OS again, the Pi wouldn’t boot to anything just using the written steps)

fbtft_device name=waveshare32b gpios=dc:22,reset:27 speed=48000000 width=320 height=240 buswidth=8 init=-1,0xCB,0x39,0x2C,0x00,0x34,0x02,-1,0xCF,0x00,0XC1,0X30,-1,0xE8,0x85,0x00,0x78,-1,0xEA,0x00,0x00,-1,0xED,0x64,0x03,0X12,0X81,-1,0xF7,0x20,-1,0xC0,0x23,-1,0xC1,0x10,-1,0xC5,0x3e,0x28,-1,0xC7,0x86,-1,0×36,0x28,-1,0x3A,0x55,-1,0xB1,0x00,0x18,-1,0xB6,0x08,0x82,0x27,-1,0xF2,0x00,-1,0×26,0x01,-1,0xE0,0x0F,0x31,0x2B,0x0C,0x0E,0x08,0x4E,0xF1,0x37,0x07,0x10,0x03,0x0E,0x09,0x00,-1,0XE1,0x00,0x0E,0x14,0x03,0x11,0x07,0x31,0xC1,0x48,0x08,0x0F,0x0C,0x31,0x36,0x0F,-1,0×11,-2,120,-1,0×29,-1,0x2c,-3

ads7846_device model=7846 cs=1 gpio_pendown=17 speed=1000000 keep_vref_on=1 swap_xy=0 pressure_max=255 x_plate_ohms=60 x_min=200 x_max=3900 y_min=200 y_max=3900

After following this tut to the letter on a brand new image of Raspian, I find that the touch driver does not function. Anyone experience the same? Basically all I did was image a current copy of rasping, did a apt-get upgrade, and then did this tutorial. Then the touch driver does not work, meaning the pointer does not respond.

The reason I did this was because on a production version of my system I added the 3.2 screen and it worked great except for the x-axis. So I wanted to see if there was something in my system that was interfering or if this is another error. Now with a raw rasping the driver does not work at all. I wonder if the touch pin has changed since the kernel is using BCM pins instead of GPIO pin numbers?

I have exactly the same problem. I also installed a new version of Raspbian, and the LCD part works fine (except all the windows are way too large), but the touch part doesn’t work at all… I’m using Waveshare Spotpear 3.2″ V4.

I remember that I plugged in the screen wrongly one time, before configuring any of the GPIO pins. Can this have damaged the screen? Still it’s weird that the display part works well and the touch part not at all.

I do not think that has anything to do with it. Other than power pins, the rest are communication. If it still works then you are good. No, there is something else. I do suspect it us related to the BCM pin numbering. The real question is… Why isnt the eeveloper responding? I have since abandoned this TFT because of his lack of response.

Touch actually goes through one of the SPI pins I think. Either the driver is toast with the required kernel update or the driver is using the wrong pin. It is very likely the this works well with previous raspian versions, but not with the new B+ and with the new kernel.

I am trying to use the sainsmart 2.8″ lcd sold through microcenter, using the sainsmart32_spi … seems to have the same pinouts, should I be able to get this to work? I am stuck at the white out screen on the lcd, doesn’t seem to recognize the module either.

Unfortunately I’ve tried that ( a few times actually) but the file still doesn’t exist. Thanks very much for the assistance anyway. I must be doing something wrong. My Raspian came from a Noobs installation, I’m wondering if I should try installing the OS from somewhere else. My LCD screen didn’t come with a CD or any docs so I’m completely in the dark here.

I have just found a way to get this file on my system! Apparently its part of the fbturbo installation. I found it here http://www.raspberrypi.org/forums/viewtopic.php?f=63&t=45746&start=75 (under experimental enhanced x driver (rpifb).. Sorry if this is obvious to everyone but I am SUCH a noob at this!!

I have the waveshare 3.5 and what to use it only as a secondary screen by putting measurement data with a c program on the screen. Is there any solution?

Ok, what am I doing wrong. I am using a fresh install of the newest raspbian, on a Pi 2. After doing the first two steps and rebooting I get the rainbow screen, then the boot up process, and then my screen just goes black with a flashing cursor in the top left. I am not able to enter any commands or anything…like the pi is halting just after boot up. Any thoughts/suggestions would be greatly appreciated. Thanks.

Well figured out that step 1 was causing my problems. I’m guessing it is shutting off my hdmi feed and trying to switch it over to the SPI, am I guessing right? If so, not sure how I’m suppose to complete the rest of the steps if my hdmi output gets turned off before the LCD is actually set up to work…that sounds kind of smartass-like, which is not my intention, just looking for some clarification on what is going on in that first step as I am fairly new to this stuff. Thanks.

Anyway, I was able to do the rest of the steps with no problem. LCD didn’t work, but I am using a Waveshare 3.5, which doesn’t look to be supported yet. Mostly I am trying to play around and see if I can get it working somehow. Anyone found a way to do this yet?

I am having an issue with getting the GUI back. Every time I use startx my pi just sits there for about two minutes saying “No protocol specified”, and then it just gives up. I went through this tutorial about four times now and am not certain why it is doing this. I have the exact same LCD as is in the tutotial (WaveShare 3.2b). any help would be great.

Hi I am making a project for school,using the raspberry pi b+ and waveshare spotpare 3.2b. Everything works except the touch input doesn’t work. Any help would be appreciated very much.

Thanks for the tutorial. It works, but I get the boot/command line stuff on the HDMI monitor and the LCD only comes on when I do startx. Is there a way to get everything to appear on the LCD screen?

I am trying to get this same screen to work with the image of RetroPie 2.6 and it won’t work. I have followed all the steps and nothing, please help I an kinda a noob.

I have a Tontec 7 inch touchscreen with a Raspberry Pi 2 B. After following the instructions the touch screen is functioning but not properly… The only are that works is the upper left (and only a small area of that). I tried changing the width and height in the modules but it didnt change anything. Also the xy seems to be reversed, I changed the swap_xy to 1 but again no change on the screen.

Now the OS freezes at the emulation station loading screen, and if I connect my lcd it gives me a lot of error messages which I can only see on the 3.2 inch screen.

hi i have the same screen with a raspberry pi 2 im trying to run retro pie but it wont show ..however it shows all the commands …but i cant get it to show the gui …if u guys can make an image or something please i have been in this pain for two weeks already thank you

well ,,i follow all instructions and still kernel panic ,,,,may i request from mr. Circuitbasics@Gmail.Com that have a contact with manufacture and just ask for 2-3 links for image files for different versions of pi till all this f discussions are finished,,i cant understand 10 guys said we run it and 40 guys said kernel panic ,,as an expert i did 50 times imaging and follow all changes fro this forum and other forums and still cant run it ,,,so sth is wrong …..just asking the manufacture for simple f image ,,that`s it ,,,,simpleeeeeeeeeeeeeeeee

well i did it at last on pi 2,,after reading 100 pages and reimaging 50 times ,,i finally find the solution ,,,,there is a simple line forgotten to be attached in setup instruction,,,well i give u clue for prodigies ,,there is a step left between step 3 and 4,,,,and a simple change in step 5 according to your pi version ,,,that`s it ,,nothing else,,,,

Damn.. I thought I was kickin ass haha. I am using the SainSmart 3.2″.. the backlight is lit up and the pi was booting and everything just fine but on the final reboot it gets hung and says “nonblocking pool is initialized” ?? No idea what that means. But it’s def just frozen at this point.. on my main screen, and just the backlight is on the SainSmart.

This was an excellent tutorial. I have gotten an output to the screen, but no touchscreen usage . I have the Waveshare SpotPear 3.2 Inch LCD V4 screen, but using Raspberry PI 2 with wheezy. Any ideas?

Thanks a lot for this article. Very clear and easy . I am new in pi’s world and my 3.2″ screen is working fine. I rotate 90 º and works. I can use mouse and so on.Not problems.

I filed the steps to calibrate the screen but it did not work.I think because it did not find the TFT pin, because I think the touch problem is the assigned pin to control it changed.

I actually used the driver from here http://www.waveshare.com/wiki/3.2inch_RPi_LCD_(B) , from a new wheezy build, did nothing except enable SPI in config, install driver, and change mmcblk0p2 to mmcblk0p6 in cmdline.txt and it all worked, no drama.

Hi I managed to set up my touch screen ok but I now have the issue that everything desktop fits fine but the windows I open are all huge and I can’t remember how to change the size and cannot see the option in desktop preferences any idea what I have to do and is it at all possible to install kodi to run through the raspbian is as this would be a lot my useful than having to keep swapping os on every boot up many thanks in advanced hope you can help me

Advice to all who have the drivers from the (touch)screen manufacturer and cannot obtain those otherwise: you can skip everything and go to the update steps skipping the kernel and kernel modules update (as mentioned by the author) so that you don’t override the preinstalled drivers. I have a Waveshare 3.5″ RPi v3 (not the 3.2″ supported by notro’s drivers) and actually managed without any problems to get notro’s drivers make it work. However I am still reading about the xinput and xinput-calibrator to figure out how to include it as a kernel module so that I can compile my own kernel and add it there.

i have raspberry pi 2 with 3.2 inch rpi lcd v4 waveshare spotpear.i have done as per your instructions.the display is working but touch screen not working.error shows waveshare32b module not found as well as touch screen module not found messages.

Hey! i did this and rotated it… It loads console perfectly, but when it goes into startx, i get a black background with only the wastebin/trashcan… how do i get the taskbar(or whatever that bar is called)? and the raspberry background?

Unfortunately I have lost the Touch facility on my Waveshare 3.5″ LCD Touchscreen? Can you offer any reasons as to why? I copied the Raspbian image to my Raspberry Pi from the Waveshare website first of all. The Touchscreen displays but is not reactive with any touch

I have purchased a raspberry pi B+ total kit and waveshare 3.2 TFT display online. In the package i have been given a pre-loaded NOOBS installed SD card. I did not even start anything yet. What should i do what r the things needed and how to connect the display i really want to know. I need help as i don’t know anything. Does the above solution help or will u suggest something………………..

Hi great article thanks. I am trying to get a waveshare 7 inch LCD with capacitive touch running it works with the suppled image but if you upgrade it breaks the capacitive touch. I have a sense-hat and GPS which require the latest kernel and RASPIAN image and the install program for the screen replaces the /lib/modules directory and the kernel with older ones. I need to be able to install the touch drivers into a new clean OS can anyone give me some pointers? Thanks

I should add that the screen is plugged into the HDMI port and always works. The capacitive touch is driven from the USB port which also supplies power.

I have the WaveShare 3.5 (A) and cannot get it to work with the Kali Linux with TFT for Raspberry Pi. Have anybody gotten the A to work? (Not the B, theres instructions for the B already and dont work with A)

So I have the original image that came with my screen and it works fine with the LCD but my problem is that I want to use my LCD screen with other distros (at this time I am trying to use it with Kali Linux with TFT support by default https://www.offensive-security.com/kali-linux-vmware-arm-image-download/) What do I have to do to transfer the needed files from the original image that WORKS with the screen and use them with another image?

I originally bought this bundle http://www.amazon.com/gp/product/B013E0IJUK?psc=1&redirect=true&ref_=oh_aui_detailpage_o02_s00 with an RPi LCD V3 and no extra documentation on the specifics on the chipset. I tried with the bftft drivers but since I have no idea what to call this screen I just suppose it isn’t supported.

After 4 lost days I just decided to get another screen, a Waveshare 3.2 (just like the one on this tutorial), I’ll follow these steps and see if it work for me.

I’ve followed your instructions and am only getting a white screen stil. I am using the Osoyoo 3.5 inch touchscreen from Amazon. http://www.amazon.com/gp/product/B013E0IJVE?psc=1&redirect=true&ref_=oh_aui_detailpage_o01_s00

I’m not sure if the Jessie kernel is compatible – can anyone please confirm or not ?? Adafruit states that their setup for TFT screens are Wheezy only ; is this a different setup ??

I am using the same LCD and followed your tutorial. Have your tested the guide lately? Are you certain that it works? I see the boot messages on console but I get white screen as GUI starts.

Oct 16 17:38:48 spare kernel: [ 12.544859] graphic