tft lcd mega shield v1 2 brands

TFT01 LCD is working at 3.3V voltage, it cannot be used directly on top of a standard Arduino board, so in order to make TFT01 LCD compatible for using on standard Arduino board, designed section TFT Shield, can be directly plugged into the Arduino board^^TFT01 LCD 16 can support the current mode, since there is sufficient Mega2560 IO, while using only a touch screen interface or SD card interface, like in the case of face 328S will not exist^^TFT01LCD supports 8-bit mode, can use SD card interface and touch screen interface at the same time, adopts IC voltage division, makes the TFT display more stable^^This LCD TFT01 Arduino Mega shield V 2.2 is fit for 3.2 inch TFT LCD Module; The TFT01 MEGA shield supports 16-bit mode; Because of Mega board have enough pins for using SD card and touch function at the same time^^ 3.2 inch TFT LCD Shield, Can be directly to the 3.2 "TFT on the shields, can be compatible with the Arduino

3. Your data will be processed on the basis of point (a) of Article 6(1) of Regulation of the European Parliament and of the Council (EU) 2016/679 of 27 April 2016 on the protection of individuals with regard to the processing of personal data and on the free movement of such data and the repeal of Directive 95/46/EC (hereinafter referred to as: GDPR) , in order to send to the provided e-mail address, an electronic news bulletin of TME.

The SainSmart TFT LCD module works in 3.3V voltage level and you need to use cables to connect with Arduino Mega. And this shield can help you out of the bothers to use other cables. You just need to plug the module to Mega through this shield.

We try our best to reach each and every corner of India using a few of the best courier services running in the Country such as FedEx, Delhivery, DTDC, BlueDart, XpressBees, Ecom Express, etc. as per the feedback for the courier partner at the customer"s location. Few of the interior parts of India which are not covered by these courier services are covered by India-Post by us. We apply our best effort on daily basis to dispatch the order the same day it is ordered or within the next 24 hours of the order placed. Most of the orders that are placed before 1 PM are dispatched and shipped the same day. The orders placed post that is scheduled for next day shipment. The same effort is applied throughout the week including weekdays and sometimes weekends and public holidays as well. We facilitate local pickup (self-pickup for the local customers) on the weekdays and partially on weekends also.

This shield for arduino MEGA and ADK card will allow you to connect very simply all modules of the Grove range. Each Grove connector has two pins of power (VCC and GND) and two pine trees in signals.

You can find 10 connectors dedicated to the digital inputs/outputs including 4 for the serial link, 8 connectors dedicated to analog and 3 entries connectorsdedicated to the I2C connection.

Put the screen(3.2 inch screen schematic) into shield (TFT01-3.2 shield schematic) first, then connect the shield to Arduino, it is quite straight forward.

3)Download and install UTFT ,URTouch ,SdFat,UTFT_Buttons and UTFT_SdRaw library file from following link and copy them into Arduino library folder. ( i.e. D:\arduino ide\Arduino 1.6.9\libraries )

Download the test program (http://www.kookye.com/download/3.2inchscreen/3.2inchtouchscreentest.zip), upzip and open it,then choose the correct board and port.

You will see the code in each sketch: UTFT myGLCD(CTE32_R2, 38, 39, 40, 41).The first value of code refer to the mode of LCD screen. Please write CTE32_R2 or ILI9341_16 if you LCD screen is ILI9341; Please write CTE32 if you LCD screen is SSD1289;

When you use the others LCD screen from the others seller, you could check the PDF instruction in documentation file or open the UTFT.h file to find the correct code.The controller mode could be identifitied by the back mark as the following pictures.

Note: In the project of testing the SD card，please insert the SD card into the slot in back of the 3.2’’ LCD screen. The format of files in SD card must be the FAT32, you need to put the test files(i.e. ICONS.RAW,WAIT4GPS.RAW,SK45) into the SD card root directory.

We try our best to reach each and every corner of India using a few of the best courier services running in the Country such as FedEx, Delhivery, DTDC, BlueDart, XpressBees, Ecom Express, etc. as per the feedback for the courier partner at the customer"s location. Few of the interior parts of India which are not covered by these courier services are covered by India-Post by us. We apply our best effort on daily basis to dispatch the order the same day it is ordered or within the next 24 hours of the order placed. Most of the orders that are placed before 1 PM are dispatched and shipped the same day. The orders placed post that is scheduled for next day shipment. The same effort is applied throughout the week including weekdays and sometimes weekends and public holidays as well. We facilitate local pickup (self-pickup for the local customers) on the weekdays and partially on weekends also.

Seeedstudio 2.8’’ TFT Touch Shield V2.0is a multifunctionalArduino/Seeeduino/Arduino Megacompatible resistive touch screen. It can be used as display device or sketch pad. Compared with the previous version,2.8’’TFT Touch Shield V1.0, the screen driver is replaced with a more professional chip,ILI9341driver, providing different pin-saving SPI communication without sacrificing the data transmitting speed. Due to the communication method change, programs developed for the previous version need modifications before being transplanted to the new version. With an SD card module integrated also onSeeedstudio 2.8’’ TFT Touch Shield V2.0, this shield reserves great room for other expansions to your project.

This shield for arduino MEGA and ADK card will allow you to connect very simply all modules of the Grove range. Each Grove connector has two pins of power (VCC and GND) and two pine trees in signals.

You can find 10 connectors dedicated to the digital inputs/outputs including 4 for the serial link, 8 connectors dedicated to analog and 3 entries connectorsdedicated to the I2C connection.

The ITDB02 LCD module is work in 3.3V voltage level and it"s not compatible with Arduino MEGA pins, so we make a shield for Arduino MEGA. Now user can directly plug the ITDB02 in the shield and stand on the Arduino MEGA board.

The ITDB02 MEGA shield V1.1 supports both 16 bit mode and 8 bit mode ITDB02, you can use 2.4" or 3.2" with it. Different form the ITDB02 Arduino shield v1.2, now MEGA have enough pins for using SD card and Touch function at the same time. Not just the SD card and Touch function, there is a DS1307 on the board so you can also use the RTC function.

Now the latest ITDB02 library example is compatible with the ITDB02 shield but not the MEGA shield, you can modify the setting to make it compatible with MEGA shield.

How to use the SD card socket? The ITDB02 library has not include the functions for SD card, but we can offer you a existent filelogger library for Arduino, the pins of ITDB02 shield is compatible with this library. You can download it here: http://code.google.com/p/arduino-filelogger